| Age | Commit message (Collapse) | Author |
|---|
|
In the first version, the result of malloc is checked
with ut_assertnonnull. But on a fail, this macro exit
the function, so previously malloc are not freed.
So to avoid a memleak, we don't use ut_assertnonnull,
but simply check the return of malloc. If one has failed,
we freed all the allocated memory and quit the function.
Reported-by: Coverity (CID: 284403)
Reported-by: Coverity (CID: 284404)
Reported-by: Coverity (CID: 284405)
Reported-by: Coverity (CID: 284406)
Reported-by: Coverity (CID: 284407)
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Currently the size of pci_addr_t and pci_size_t depends on
CONFIG_SYS_PCI_64BIT. For qemu_arm64_defconfig with 4 GiB RAM this leads
to an error
pci_hose_phys_to_bus: invalid physical address
which is due to the truncation of the bus address in _dm_pci_phys_to_bus.
Defining CONFIG_SYS_PCI_64BIT is not a solution as this results in an error
PCI: Failed autoconfig bar 10
So let's use unsigned long for pci_addr_t and pci_size_t if
CONFIG_SYS_PCI_64BIT is not defined.
Considering that 32bit U-Boot is used to launch some 64bit x86 systems we
cannot do without CONFIG_SYS_PCI_64BIT requiring u64 as type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-arc
As usual a bit late a couple of tiny fixes and improvements for ARC.
1. Switch from ARC UART to a convenient DW UART on ARC
simulation platforms. This became avaialble when nSIM got support
of that much more standard UART (starting from nSIM v2019.06).
FWIW also available now in Free nSIM [1].
This among other things allows us finally to use the same one binary
on all our simulators & FPGA-based emulators.
2. Disable networking support on simulated platforms as there's no
network interface in them.
3. Add Virtio net & block devices for the configuration supported
by QEMU so that we may leverage those virtual peripherals and
in fact it's possible to load uImage from TFTP server and bootm it.
4. Minor fixes for HSDK clocks.
5. Rework of how we chose and use compiler options for ARC-based boards.
In real world ARC-based designs are customized more or less but very
rarely match any of our "templates" thus it makes not much sense to
pretend we have some fixed configs, instead we now will fully reply
on a SoC or even board on getting precise set of compiler options
preferably even extracted from real HW via "tcfgen" utility.
6. Well and finally yet another simplification - switch to generic
written in C accessors which are much more universal and just work
for any target supported by the complier as compared to GAS
implementation which is much more target-dependent.
This one was heavily "inspired" by similar implementation for RISCV
and ARM.
[1] https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
|
|
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
First of all U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not super
fast as we only being executed once. That in return allows us to be more
universal and support wider variety of devices.
And looking forward that will significantly reduce maintenance and simplify
support of newer architectures.
And while at it we add quad-word accessors like readq(), writeq() etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
HDMI PLL has its own xtal with 27 MHz output but we treat it the same
way as other PLLs with 33.33 MHz input.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Pll bypass has priority over enable/disable.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.
Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is not needed now that we have SDL2 in the docker image. It causes
test failures for tests which need video to work.
This reverts commit af800722eb718bec51c5943cfb69231acf15178f.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
- Regulator fix
- Documentation fix
- Correct LOGLEVEL range
|
|
As LOGLEVEL ranges form 0 to 9 set the limit to 10.
Signed-off-by: Marek Bykowski <marek.bykowski@gmail.com>
|
|
The patch fixes some errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
ofdata_to_platdata
The commit e8e9715df2d4 ("regulator: fixed: Modify enable-active-high behavior")
fixed the regulator driver behavior when 'enable-active-high' is defined.
Unfortunately, this patch used dm_regulator_platdata()'s "boot_on" member
to set GPIOD_IS_OUT_ACTIVE flag and enable the regulator.
The issue here is that regulator_common_ofdata_to_platdata() is called
_before_ regulator_pre_probe() function in which the 'regulator-boot-on'
property is asserted.
As a result the GPIOD_IS_OUT_ACTIVE flag is not set and gpio_request_by_name()
called in the former function is not enabling the regulator.
This is problematic for e.g. i.MX ethernet driver, which then tries to
perform initialization without power (and fails).
The solution here is to explicitly enable regulator in regulator_pre_probe()
callback only when 'regulator-boot-on' property is present in device tree.
The GPIOD_IS_OUT_ACTIVE flag is not set at all, but relevant gpio is
requested.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
|
|
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix Coverity CID 280902 issue in vid_console_color()
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Convert to DM:
- bx50v3, mx53ppd, novena, mx6sabresd
- Fixes for Xea Board
- Toradex im8m Verdin
- Cleanup (warp7, mx6sxsabresd)
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/648131788
|
|
- Fix ax25-ae350.rst document.
- Refine RISC-V linker script and start.S.
- Add option to print more information on exception.
|
|
The add instruction on risc-v can have any three sources and targets, so there
is no need for an intermediate mov.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
OpenSBI build steps are marked as normal text in
AX25-AE350 documentation.
Move them into code-block so-that it can show it
as build steps.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Since commit 04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
`make htmldocs` produces a log of warnings like
doc/board/AndesTech/ax25-ae350.rst:373:
WARNING: Block quote ends without a blank line; unexpected unindent.
doc/board/AndesTech/ax25-ae350.rst:0:
WARNING: Undefined substitution referenced: "_ __ ___ _ __ | (___ | |_) |".
Reformat the problematic passages.
Fixes: 04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When debugging, it can be helpful to see more information about an
unhandled exception. This patch adds an option to view the registers at
the time of the trap, similar to the linux output on a kernel panic.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Due to the two-instruction sequence needed to access arbitrary memory
locations, the RISC-V linker aggressively optimises memory accesses and
jumps at link-time. This is called "linker relaxation," and is discussed
in this SiFive article
<https://www.sifive.com/blog/all-aboard-part-3-linker-relaxation-in-riscv-toolchain>.
One of the optimizations in place is to assume that the __global_pointer
symbol is placed in the gp register. To quote the article:
"...The magic __global_pointer$ symbol is defined to point 0x800 bytes
past the start of the .sdata section. The 0x800 magic number allows
signed 12-bit offsets from __global_pointer$ to address symbols at the
start of the .sdata section. The linker assumes that if this symbol is
defined, then the gp register contains that value, which it can then use
to relax accesses to global symbols within that 12-bit range. The
compiler treats the gp register as a constant so it doesn't need to be
saved or restored, which means it is generally only written by _start,
the ELF entry point."
However, U-Boot instead keeps the global data pointer in gp. This causes
memory accesses and jumps optimized to use the gp pointer to fail. To
fix this problem, we undefine the __global_pointer symbol.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
Configure `CONFIG_SYS_BOOTMAPSZ' per guidance on u-boot@lists.denx.de.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use `test' command to test for file existence instead of relying on the
old functionality of the `ext2load' command (which now reports an error
when attempting to load a zero length file).
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy uart pad and iomux code
Enable DM serial and mxc uart
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Override the panel compatible string for LCD in U-Boot.
Include U-Boot device tree overrides in device-specific device trees so
that the panel compatible string is used.
Fixes: 8c26739859c6 ("board: ge: bx50v3: sync devicetrees from Linux")
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Add eeprom partitions to device tree.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Set the correct offset length and chip address offset mask for each
device to allow correct access to total capacity of the devices.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
In preparation for converting to DM_ETH and moving the FEC symbols
to Kconfig we need to move the FEC definitions to mx6sabreauto.h
and mx6sabresd.h to avoid build breakage during the conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
commit 88718be30010 ("mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND")
moved CONFIG_NAND -> CONFIG_MTD_RAW_NAND. Adapt board code to this
change, as last merge did not respect the above commit.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable DM thermal driver and iMX thermal driver to get accurate
CPU frequency reporting in the boot log.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
|
|
Convert to DM ethernet to prevent board removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
|
|
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
|
|
Before:
=> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00
usb dr_mode not found
CTRL+C - Operation aborted
=> dfu 0 mmc 0
usb dr_mode not found
After :
=> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00
=> dfu 0 mmc 0
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
These nodes are not in upstream kernel, so move these in u-boot.dtsi
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
With commit 6b503f9e6549("warp7: Switch to DM USB").
These configs are not necessary
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
