summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-10-06cfi_flash: don't hide write/erase errorsBaruch Siach
Partially revert commit 0d01f66d235118 (CFI: cfi_flash write fix for AMD legacy). flash_full_status_check() used to skip status register parsing when flash_status_check() returns OK. This is wrong since flash_status_check() must return OK for other status bits to be valid. Cc: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2014-10-05git-mailrc: add me as a maintainer of UniPhier platformMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05MAINTAINERS: add me as a maintainer of UniPhier platformMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Michal Simek <monstr@monstr.eu>
2014-10-05ARM: UniPhier: add Kconfig and defconfigMasahiro Yamada
This commit allows to build Panasonic UniPhier family: PH1-LD4, PH1-Pro4, PH1-sLD8 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05ARM: UniPhier: add UniPhier SoC support codeMasahiro Yamada
These are used by Panasonic UniPhier SoC family. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05serial: add UniPhier serial driverMasahiro Yamada
The driver for on-chip UART used on Panasonic UniPhier platform. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05mtd: denali: add Denali NAND driver for SPLMasahiro Yamada
The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP. This driver requires two CONFIG macros: - CONFIG_SPL_NAND_DENALI Define to enable this driver. - CONFIG_SYS_NAND_BAD_BLOCK_POS Specify bad block mark position in the oob space. Typically 0. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com>
2014-10-05mtd: denali: add Denali controller configs to KconfigMasahiro Yamada
Commit 3eb3e72a3f66 (nand/denali: Adding Denali NAND driver support) introduced some new options, and some of them were documented by commit f9860cf081ef (nand/denali: Document CONFIG symbols). This commit allows users to enable/disable them via Kconfig with more detailed help docs. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com>
2014-10-03dw_mmc: cleanupsPavel Machek
dw_mmc driver was responding to errors with debug(). Change that to prinf so that any errors are immediately obvious. Also adjust english in comments. Signed-off-by: Pavel Machek <pavel@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03cmd_mmc: fix bootpart-resize maxarg to 4Wally Yeh
sub-command 'bootpart-resize' check for argc == 4, it will retrun CMD_RET_FAILURE when argc value not matched. but bootpart-resize's maxarg is 3, which means you never execute this sub-command successfully. fix it by change bootpart-resize maxarg to 4. Signed-off-by: wally.yeh <wally.yeh@atrustcorp.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Pierre Aubert <p.aubert@staubli.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03mmc: Fix mmc bus widthMario Schuknecht
After setting the bus width, the extended CSD register is read. Some selected fields are compared with previously read extended CSD register fields. In this comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is previously written under certain circumstances. And then the comparison fails. Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE instead of field EXT_CSD_ERASE_GROUP_DEF. Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03mvebu_mmc: Driver additionMario Schuknecht
In function mvebu_mmc_write notice command timeout. It is possible that a command is done, but a timeout occurred. Enable timeout in set bus function. Set window registers. Without that I could not use the driver on a Kirkwood 88F6282 SoC. Set high capacity and 52MHz driver feature. Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03env_mmc: correct fini partition to match init partitionPeter Bigot
The code to set the MMC partition uses an weak function to obtain the correct partition number. Use that instead of the compile-time default when deciding whether it needs to switch back. Fixes: 6e7b7df4df43574 ("env_mmc: support env partition setup in runtime") Signed-off-by: Peter A. Bigot <pab@pabigot.com> Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03mmc: restore capacity when switching to partition 0Peter Bigot
The capacity and lba for an MMC device with part_num 0 reflects the whole device. When mmc_switch_part() successfully switches to a partition, the capacity is changed to that partition. As partition 0 does not physically exist, attempts to switch back to the whole device will indicate an error, but the capacity setting for the whole device must still be restored to match the partition. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Tom Rini <trini@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-03mmc: fix ERASE_GRP_DEF handlingHannes Petermaier
if we set manually this bit on the eMMC card using mmc_switch(...), we also have to set it within our (before read) internal structure 'ext_csd'. Otherwise following checks on this will fail. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-10-03mmc: set correct block size value in bfin sdh driverSonic Zhang
Wait data transfer till the data end bit other than the data block end bit is set. Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-10-01ARM: sheevaplug: add HUSH parserDrEagle
This patch add HUSH command parser Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add HUSH command parser Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-01ARM: sheevaplug: redefine MTDPARTSDrEagle
This patch redefine MTDPARTS Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - redefine MTDPARTS Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-01ARM: sheevaplug: add MTD defaultsDrEagle
This patch add MTDIDS and MTDPARTS defaults settings to sheevaplug Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add MTDIDS and MTDPARTS default to sheevaplug Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-01ARM: sheevaplug: add MVSATA driverDrEagle
This patch add MVSATA driver to sheevaplug Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v1: - add MVSATA driver to sheevaplug - enable ext4 FS support Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-01ARM: sheevaplug: change env locationDrEagle
This patch move the environment offset in sheevaplug. The size of the u-boot binary is become too big. Fix saving environments was result of corrupting the u-boot. Signed-off-by: Gerald Kerma <drEagle@doukki.net> Changes in v2: - patch description Changes in v1: - fix sheevaplug environment offset Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-01wandboard: Select CONFIG_CMD_FUSEFabio Estevam
Select CONFIG_CMD_FUSE so that the fuse API commands can be used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-01ARM: mx6: gw_ventana: Remove superfluous memset of GD in board_init_fStefan Roese
Zeroing GD in board_init_f() is not needed any more. As its now done in crt0.S. The patch that clears the GD in crt0.S is this one: aae2aef9 [arm: Set up global data before board_init_f()] from Simon. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
2014-10-01imx6sx: Fix i.MX6SX HAB api function table offsetNitin Garg
i.MX6SX ROM implements unified table sections. The HAB function table is at offset 0x100. Update the HAB function pointers accordingly. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-09-30imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boardsYe.Li
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2 arm2 board. Since the LPDDR2 arm2 board has different DDR size, use CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-30imx: mx6dlarm2: Add support for i.MX6DL arm2 DDR3 boardYe.Li
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2 shared the same board with i.MX6Q ARM2 board since the i.MX6DL is pin-pin compatible with i.MX6Q. The patch also support the DDR 32-BIT mode option. Please define CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT mode.But due to the board design, it's 64bit DDR buswidth physically, so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29arm: m53evk: Enable FS_GENERICMarek Vasut
Enable the CONFIG_CMD_FS_GENERIC on m53evk to avoid per-fs specific commands and tweak the environment to cater for this new option. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: m28evk: Enable FS_GENERICMarek Vasut
Enable the CONFIG_CMD_FS_GENERIC on m28evk to avoid per-fs specific commands and tweak the environment to cater for this new option. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: m53evk: Test if bootscript exists before loading itMarek Vasut
Make sure the boot.scr exists on the card before loading it from the card to avoid annoying message on the console. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: m28evk: Test if bootscript exists before loading itMarek Vasut
Make sure the boot.scr exists on the card before loading it from the card to avoid annoying message on the console. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29usb: ehci-mx6: Rename the USB register base addressYe.Li
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name "USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes the USB base address name to "USBOH3", which causes the driver failed to build for mx6sl/mx6sx. This patch uniform the address name to "USB_BASE_ADDR" for all mx6 series. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29imx: mx6: Checking PLL2 PFD0 and PFD2 for periph_clk before PFD resetYe.Li
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source, do not reset this PFD to avoid system hang. Customers may set this in DDR script or use BT_FREQ to select low freq boot. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29imx: mx6qarm2: Change the mmcroot and mmcpart env valueYe.Li
1. Set the image load partition to the first FAT partition. 2. Set the kernel rootfs partition to the second partition. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29imx: mx6qarm2: Add the kernel FDT Loading supportYe.Li
To support loading FDT file for kernel, add the fdt address, file and loading script to arm2 board default environment. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29arm: mxs: olinuxino: Fine-tune DRAM configurationMarek Vasut
Add fine-tuning for the DRAM configuration according to the DRAM chip datasheet. THis configuration applies to both Hynix HY5DU12622DTP and Samsung K5H511538J-D43 . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: mxs: olinuxino: Enable USB only when neededMarek Vasut
Enable the power to the USB port only when the USB port is really needed. Do not enable the power unconditionally. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: mxs: Wait for DRAM to startMarek Vasut
Instead of waiting for a fixed period of time and hoping for the best that the DRAM will start, read back an EMI status register which tells us exactly when the DRAM started. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29arm: mxs: Wait when disabling VDDMEM current limiterMarek Vasut
According to i.MX23 datasheet Table 32-17, we must wait for the supply to settle before disabling the current limiter. Indeed, not waiting a little here causes the system to crash at times. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-29usb: ehci: mxs: Add board-specific callbacksMarek Vasut
Add board-specific callbacks for enabling/disabling port power into the MXS EHCI controller driver. This is in-line with the names of callbacks on other systems. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-09-26Merge branch 'for-tom' of git://git.denx.de/u-boot-dmTom Rini
2014-09-26spi: Add brackets and tidy defines in spi.hSimon Glass
Some of the #defines in spi.h are not bracketed. To avoid future mistakes add brackets. Also add an explanatory comment for SPI_CONN_DUAL_... Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-26dm: spi: Move cmd device code into its own functionSimon Glass
In preparation for changing the error handling in this code for driver model, move it into its own function. Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-26sandbox: config: Enable all SPI flash chipsSimon Glass
Sandbox may as well support everything. This increases the amount of code that is built/tested by sandbox, and also provides access to all the supported SPI flash devices. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-26sandbox: Convert SPI flash emulation to use sf_paramsSimon Glass
At present sandbox has its own table of supported SPI flash chips. Now that the SPI flash system is fully consolidated and has its own list, sandbox should use that. This enables us to expand the number of chips that sandbox supports. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-26Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2014-09-26Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2014-09-25nand/denali: Document CONFIG symbolsScott Wood
The patch "nand/denali: Adding Denali NAND driver support" introduced two config symbols without documenting them. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Chin Liang See <clsee@altera.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25nand/denali: Adding Denali NAND driver supportChin Liang See
To add the Denali NAND driver support into U-Boot. This driver is leveraged from Linux with commit ID fdbad98dff8007f2b8bee6698b5d25ebba0471c9. For Denali controller 64 variance, you need to declare macro CONFIG_SYS_NAND_DENALI_64BIT. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25mtd: nand: Fix length bug in ioread16_rep() and iowrite16_rep()Stefan Roese
The ioread16_rep() and iowrite16_rep() implementations are U-Boot specific and have been introduced with the Linux MTD v3.14 sync. While introducing these functions, the length for the loop has been miscalculated. The ">> 1" is already present in the caller. So lets remove it in the function. Tested on omap3_ha. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2014-09-25mtd: nand: am335x: Fix 'bit-flip' errors in SPLRostislav Lisovy
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip corrected' error messages. Possible cause was discussed in the mailinglist thread: http://lists.denx.de/pipermail/u-boot/2014-April/177508.html The issue was partially fixed with the cc81a5291910d7a.git however this has to be done to fix the SPL. The original author of the code is Belisko Marek <marek.belisko@gmail.com> Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
generated by cgit (git 2.34.1) at 2025-02-23 16:19:49 +0000