summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-03-19TQM5200B: update MTD partition layoutMartin Krause
- insert partition for dtb blob to TQM5200B MTD layout - set env variables dependent on the configured board (TQM5200 or TQM5200B) Signed-off-by: Martin Krause <martin.krause@tqs.de>
2008-03-18lwmon5: Fix register test logic to match the specific GDC h/w.Yuri Tikhonov
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18Fix backlight in the lwmon5 POST.Yuri Tikhonov
Backlight was switched on even when temperature was too low. Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18The patch introduces the alternative configuration of the log buffer for the ↵Yuri Tikhonov
lwmon5 board: the storage for the log-buffer itself is OCM(on-chip memory), the log-buffer header is moved to six GPT registers (PPC440EPX_GPT0_COMP1, ..., PPC440EPX_GPT0_COMP5). To enable this, alternative, configuration the U-Boot board configuration file for lwmon5 includes the definitions of alternative addresses for header (CONFIG_ALT_LH_ADDR) and buffer (CONFIG_ALT_LB_ADDR). The Linux shall be configured with the CONFIG_ALT_LB_LOCATION option set, and has the BOARD_ALT_LH_ADDR and BOARD_ALT_LB_ADDR constants defined in the lwmon5 board-specific header (arch/ppc/platforms/4xx/lwmon5.h). Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18Add support for the lwmon5 board reset via GPIO58.Yuri Tikhonov
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18Some fixes to dspic, fpga, and gdc post tests for lwmon5. Disable external ↵Yuri Tikhonov
watch-dog for now. Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18The patch introduces the CRITICAL feature of POST tests. If the test marked ↵Yuri Tikhonov
as POST_CRITICAL fails then the alternative, post_critical, boot-command is used. If this command is not defined then U-Boot enters into interactive mode. Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18The patch adds new POST tests for the Lwmon5 board. These are:Yuri Tikhonov
* External Watchdog test; * dsPIC tests; * FPGA test; * GDC test; * Sysmon tests. Signed-off-by: Dmitry Rakhchev <rda@emcraft.com> Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
2008-03-18Enable CODEC POST with CFG_POST_CODEC rather than with CFG_POST_DSP.Yuri Tikhonov
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
2008-03-18Merge branch 'master' of git://www.denx.de/git/u-boot-blackfinWolfgang Denk
2008-03-18HMI1001: fix compile problem.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-15Blackfin: BF537-stamp: drop board-specific flash driver for CFIMike Frysinger
The parallel flash on the BF537-STAMP is CFI compliant, so there is no need for the board specific driver at all. Just use the common CFI driver. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15Blackfin: add proper ELF markings to some assembly functionsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15Blackfin: new cplbinfo command for viewing cplb tablesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15Blackfin: update MAINTAINERS listMike Frysinger
Add maintainer information for the Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15Blackfin: convert BFIN_CPU to CONFIG_BFIN_CPUMike Frysinger
Stop tying things to the processor that should be tied to other defines and change BFIN_CPU to CONFIG_BFIN_CPU so that it can be used in the build system to select the -mcpu option. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15Blackfin: move bootldr command to common codeMike Frysinger
This moves the Blackfin-common bootldr command out of the BF537-STAMP specific board directory and into the common directory so that all Blackfin boards may utilize it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-16Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/masterWolfgang Denk
Conflicts: drivers/rtc/Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-16mgcoge: update configurationHeiko Schocher
Fix configuration for mgcoge board Signed-off-by: Heiko Schocher <hs@denx.de>
2008-03-16drivers/rtc/Makefile: keep list sortedWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-16Add support for Intersil isl1208 RTCTor Krill
Signed-off-by: Tor Krill <tor@excito.com>
2008-03-16cramfs: Fix ifdefJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-03-16Conding style cleanupWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-15ppc4xx: Add USB OHCI support to AMCC Canyonlands 460EX eval boardStefan Roese
This patch adds USB OHCI support to the Canyonlands board port. It also enables EXT2 support. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15usb: Add CFG_OHCI_USE_NPS to common USB-OHCI driverStefan Roese
This patch adds CFG_OHCI_USE_NPS to the common USB-OHCI driver. This way a board just needs to define this new option to enable the "force NoPowerSwitching mode" instead of adding new CPU/architecture defines to the USB source itself. This new option will be used first with the new AMCC 460EX Canyonlands board port, which will be posted in a few days. This patch also fixes a small compilation problem when DEBUG is enabled. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add Canyonlands NAND booting supportStefan Roese
460EX doesn't support a fixed bootstrap option to boot from 512 byte page NAND devices. The only bootstrap option for NAND booting is option F for 2k page devices. So to boot from a 512 bype page device, the I2C bootstrap EEPROM needs to be programmed accordingly. This patch adds basic NAND booting support for the AMCC Canyonlands aval board and also adds support to the "bootstrap" command, to enable NAND booting I2C setting. Tested with 512 byte page NAND device (32MByte) on Canyonlands. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add AMCC Canyonlands support (460EX) (3/3)Stefan Roese
This patch adds support for the AMCC Canyonlands 460EX evaluation board. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add AMCC Canyonlands support (460EX) (2/3)Stefan Roese
This patch adds support for the AMCC Canyonlands 460EX evaluation board. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add AMCC Canyonlands support (460EX) (1/3)Stefan Roese
This patch adds support for the AMCC Canyonlands 460EX evaluation board. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add basic support for AMCC 460EX/460GT (5/5)Stefan Roese
This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add basic support for AMCC 460EX/460GT (4/5)Stefan Roese
This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add basic support for AMCC 460EX/460GT (3/5)Stefan Roese
This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add basic support for AMCC 460EX/460GT (2/5)Stefan Roese
This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add basic support for AMCC 460EX/460GT (1/5)Stefan Roese
This patch adds basic support for the AMCC 460EX/460GT PPC's. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: interrupt.c reworkedStefan Roese
This patch is a rework of the 4xx interrupt handling done while adding the 460EX/GT support. Interrupts are needed on 4xx for the EMAC driver. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: program_tlb now uses 64bit physical addessStefan Roese
This patch changes the physical addess parameter from 32bit to 64bit. This is needed for 36bit 4xx platforms to access areas located beyond the 4GB border, like SoC peripherals (EBC etc.). Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: miiphy.c reworkedStefan Roese
While adding the 460EX/GT support I reworked the 4xx miiphy code. It badly neede some cleanup. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15rtc: Add M41T62 supportStefan Roese
This patch add support for the STM M41T62 RTC. It is used and tested on the AMCC Canyonlands 406EX platform. Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15ppc4xx: Add 405GPr based MCU25 board specific filesNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15ppc4xx: Add 405GPr based MCU25 board config fileNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15ppc4xx: Add 405GPr based MCU25 board. Global filesNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15ppc4xx: HCU4/5. remove obsolete hcu_flash.cNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15ppc4xx: HCU4/5. Use FLASH_CFI_LEGACYNiklaus Giger
Cleanup: Remove custom flash driver for 8 bit boot-eprom and replace it with the FLASH_CFI_LEGACY et al. config options. Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-03-15ppc4xx: Fix comment in 405EX DDR2 init codeStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-14tools/setlocalversion: use a git-describe-ish formatWolfgang Denk
Change the automatic local version to have the form -nnnnn-gSHA1SUMID, where 'nnnnn' is the number of commits since the last tag (i.e., 1.3.2-rc3). This makes it much easier to recognize "newer" versions and to see how much has been changed since the referenced tag. Stolen from Linux kernel's scripts/setlocalversio, see commit d882421f. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-13HMI1001: add support for MPC5200 Rev. B processors.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-13TQM5200: remove dead codeWolfgang Denk
This board never used a MGT5100 processor. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-09Release v1.3.2Wolfgang Denk
Update CHANGELOG for release. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-09SCM: fix 'packed' attribute ignored for field of type 'can_msg_t' warningsJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-09scb9328: Fix flash warning: type qualifiers ignored on function return typeJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit (git 2.34.1) at 2024-12-26 05:59:32 +0000