| Age | Commit message (Collapse) | Author |
|---|
|
Remove unused DDRC register macros.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.
The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC: PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE: Configureing TZASC380
NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE: BL31: Built : 09:28:54, Nov 8 2018
lpddr4 swffc start
NOTICE: sip svc init
U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM: 3 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Introduce DDR driver for i.MX8M. The driver will be used by SPL to
initialze DDR PHY and DDR Controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce lpddr4 header file
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No need to build bootaux in SPL stage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
imximage.cfg will be used to generate the flash.bin
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce script to generate fit image for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add MMC BOOT Device for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Rename mx8m,MX8M to imx8m,IMX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
|
|
Introduce is_imx8mq header macro
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce CHIP_REV_2_1 macro.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
If we don't define CONFIG_SPL_FIT_IMAGE_TINY, when loading images from FIT,
the SPL will record all loadables' info to u-boot's FDT. This causes
problem when HAB is enabled, because FDT's content is modified before
we authenticate it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce CONFIG_FIT_EXTERNAL_OFFSET to give user a choice to choose
where to put the external data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8M bootable image type is like i.MX6/7, but there is signed HDMI
firmware image in front of A53 bootable image, which is also has an IVT
header.
Here we also include fit image to generate a bootable image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
|
|
Enable driver model for USB, MMC and REGULATOR drivers.
Set run-time configuration via Device Tree.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
|
|
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This implementation comply with other iMX devices pinctrl drivers already
available in U-boot.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Introduce function prototypes for board_spl_fit_size_align and
board_spl_fit_post_load
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Using ulong is wrong as its size depends on the Host CPU architecture
(32-bit vs. 64-bit) although the Cortex-M4 is always 32-bit.
Without this patch, the stack and PC are obviously wrong and it
generates an abort when used on 64-bit processors such as the i.MX8MQ.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Otherwise can't boot the M4 core as it is impossible to load its
firmware into the TCM memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
Replace non-portable operator == with =
The operator == in sh(1) / test(1) is non-POSIX and only implemented by
some shells (like bash). It is equivalent to the standard defined operator =.
|
|
In order to boot faster with falcon mode, we need to add SPL
support to riotboard.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
|
|
config.h is not needed, remove it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
This fixes two small typos in mxsimage.txt.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
|
|
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
|
|
CONFIG_CMD_BOOTEFI is enabled by Kconfig default, but rarely
used on this board/platform.
So let's disable it for the boards default config.
This also saves around 16 KiB in the final u-boot.sb.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
|
|
While migrating individual status led usages to Kconfig stuff,
a (random) value was introduced for this board which does not
work but produces the following error message during boot:
__led_init: failed requesting GPIO59!
Since Kconfig does not seem to accept a define as this point,
but the mxs gpio driver requires not only a simple integer value,
we need to use the plain value of MX23_PAD_SSP1_DETECT__GPIO_2_1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Fixes: 2d8d190c8394 ("status_led: Kconfig migration")
|
|
Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.MX50, i.MX53
Only tested on i.MX53 hardware but in both modes
(by modifying the device tree).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
|
|
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
|
|
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
|
|
Merge functionality duplicated in bx50v3 and mx53ppd: the logic
is the same except that process_vpd is called at different phases.
Also read_vpd could end up in error, so there is no VPD data in this
case - it shouldn't be processed.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
|
|
Register the 'bootm' function for booting VxWorks kernel for
RISC-V architecture.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
For future extension to other architectures, make do_bootm_vxworks()
a non-static function.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Change the scope of do_bootvx_fdt() to static since it is only
used in common/bootm_os.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This includes x86 edison defconfig file clean up, and coreboot file
system (cbfs) fixes.
|
|
Current CBFS component type list is incomplete. Add missing ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present there are 2 macros that are named as CBFS_COMPONENT_xxx.
Change them to CBFS_TYPE_xxx for consistency.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The call to file_cbfs_fill_cache() is given with the parameter
'start' pointing to the offset by the CBFS base address, but
with the parameter 'size' that equals to the whole CBFS size.
During CBFS walking through, it checks files one by one and
after it pass over the end of the CBFS which is 4GiB boundary
it tries to check files from address 0 and so on, until the
overall size the codes checked hits to the given 'size'.
Fix this by passing 'start' pointing to the CBFS base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
cbfs_fileheader.len indicates the content size of the file in the
cbfs, and it has nothing to do with cbfs_fileheader.offset which
is the starting address of the file in the cbfs.
Remove such check in file_cbfs_next_file(). Before this change
'cbfsinit' failed with 'Bad CBFS file'. After this change all cbfs
commands are working as expected.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
[bmeng: keep the necessary header sanity check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Since some options had been moved to defconfig from header,
the leftover comments are not needed anymore. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use defconfig instead of header file for CONFIG_BOOTCOMMAND.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use defconfig instead of header file for CONFIG_CMD_PCI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.
Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.
This reverts commit a8011eb84dfac5187cebf00ed8bc981bdb5c1fa1.
Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
With enabled default Nimbus font dm_test_video_truetype* tests fail.
Update expected expressions to fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
