summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-09-11Merge tag 'u-boot-rockchip-20190912' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - add idbloader.img target for rockchip tpl+spl; - usb ehci/ohci: go on process if clock driver don't have clk_enable(); - remove clk_enable() for rockchip clock drivers; - add boot order for rockpro64
2019-09-11efi_loader: parameter checks EFI_FILE_PROTOCOL.SetInfo()Heinrich Schuchardt
We do not support volume label changes. No parameter checks are needed here. When the info for as file is changed the buffer must always contain a file name. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-11doc: lion_rk3368: use idbloader.img for rk3368Matwey V. Kornilov
Makefile now produces ready-to-deploy idbloader.img file. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-11doc: rockchip: use idbloader.img for rk3288, rk3328, rk3399Matwey V. Kornilov
Makefile now produces ready-to-deploy idbloader.img file. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-11rockchip, Makefile: add idbloader.img targetMatwey V. Kornilov
Many Rockchip platforms require the same u-boot deploy procedure when TPL and SPL both enabled. The following examples are taken from doc/README.rockchip and board/theobroma-systems/lion_rk3368/README: RK3288: ./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out cat ./spl/u-boot-spl-dtb.bin >> out sudo dd if=out of=/dev/mmcblk0 seek=64 RK3328: ./tools/mkimage -n rk3328 -T rksd -d ./tpl/u-boot-tpl.bin idbloader.img cat ./spl/u-boot-spl.bin >> idbloader.img sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64 RK3368: ./tools/mkimage -n rk3368 -T rksd -d tpl/u-boot-tpl.bin spl-3368.img cat spl/u-boot-spl-dtb.bin >> spl-3368.img dd if=spl-3368.img of=/dev/sdb seek=64 RK3399: ./tools/mkimage -n rk3399 -T rksd -d ./tpl/u-boot-tpl-dtb.bin out cat ./spl/u-boot-spl-dtb.bin >> out sudo dd if=out of=/dev/sdc seek=64 Here, we introduce generic idbloader.img target which is the TPL image followed by the SPL binary. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clean makefile for misc.cKever Yang
Use obj-$(config) instead of #ifdef $config to make the code looks clean, and move the misc_init for U-Boot proper only. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: not depends on TPL_BUILD for rk3188 makefile includingKever Yang
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add this again in parent Makefile, remove it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clk: rk3399: remove clk_enable()Kever Yang
There is no real driver for clk enable/disable now, and we actually don't need it now, remove it so that not waste CPU cycles and code size. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clk: rk3368: remove clk_enable()Kever Yang
There is no real driver for clk enable/disable now, and we actually don't need it now, remove it so that not waste CPU cycles and code size. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clk: rk3328: remove clk_enable()Kever Yang
There is no real driver for clk enable/disable now, and we actually don't need it now, remove it so that not waste CPU cycles and code size. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11rockchip: clk: rk3288: remove clk_enable()Kever Yang
There is no real driver for clk enable/disable now, and we actually don't need it now, remove it so that not waste CPU cycles and code size. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11usb: ohci-generic: don't probe fail if there is no clk_enable() opsKever Yang
Some clock driver do not have a clk_enable() call back, and we should not treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk() do not return fail if ret value is '-ENOSYS' Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-09-11usb: ehci-generic: don't probe fail if there is no clk_enable() opsKever Yang
Some clock driver do not have a clk_enable() call back, and we should not treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk() do not return fail if ret value is '-ENOSYS' Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-09-11rockchip: rk3399: dts: add boot order for rockpro64Kever Yang
The rk3399 rockpro64 board can boot from emmc and sdcard. TODO: add spiflash as boot device. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-09-11usb: musb_hcd: fix compilation errorJean-Jacques Hiblot
commit 65c1f9820c8f79f "usb: Add nonblock argument to submit_int_msg" breaks the musb_hcd driver. Fixing it by adding the missing argument Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-09-11dwc2: use the nonblock argument in submit_int_msgMichal Suchanek
An USB 1.1 keyboard connected to dwc2 through a high-speed hub does not report status until it changes. With this patch you can enable keyboard by pressing a key while USB devices are probed. Without a keypress no state is reported and the probe times out. We don't want to wait for a keypress or timeout while polling for keypresses so implement an int_msg nonblock variant that exits early on error. Signed-off-by: Michal Suchanek <msuchanek@suse.de>
2019-09-11usb: Add nonblock argument to submit_int_msgMichal Suchanek
This will be used to implement non-blocking keyboard polling in case of errors. Signed-off-by: Michal Suchanek <msuchanek@suse.de>
2019-09-11usb: storage: submit_int_msg -> usb_int_msgMichal Suchanek
Use the wrapper as other callers do. Signed-off-by: Michal Suchanek <msuchanek@suse.de>
2019-09-11usb: usb_submit_int_msg -> usb_int_msgMichal Suchanek
This aligns naming with usb_bulk_msg and usb_control_msg. Signed-off-by: Michal Suchanek <msuchanek@suse.de>
2019-09-11usb_kdb: only process events successfully receivedMichal Suchanek
Causes unbound key repeat on error otherwise. Signed-off-by: Michal Suchanek <msuchanek@suse.de>
2019-09-10Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Tangier ACPI table fixes - Support getting high memory size on QEMU x86 - Show UEFI images involved in crash for x86 - EFI loader conventional memory map fix
2019-09-10Merge tag 'u-boot-amlogic-20190910' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Add support for dis_u2_susphy_quirk in the xhci-dwc3 driver to fix boot when a device is plugged only in the OTG capable port for libretech-ac and libretech-cc
2019-09-10x86: tangier: Use spaces over TABs in ASL codeAndy Shevchenko
For sake of consistency use spaces over TABs in ASL code. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: tangier: Fix off-by-one error when preparing CSRTAndy Shevchenko
Intel iDMA 32-bit controller has 17 bits for the maximum block size value. Due to nature of the binary number representation the maximum value is 2^17 - 1. The original code misses the latter part in equation. Fixes: 5e99fde34a77 ("x86: tangier: Populate CSRT for shared DMA controller") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: tangier: Reserve PCI ECAM in motherboard resourcesAndy Shevchenko
Per PCI firmware specification the ACPI has to reserve the memory which is defined as PCI ECAM. Fixes: 39665beed6f7 ("x86: tangier: Enable ACPI support for Intel Tangier") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: acpi: Annotate struct acpi_table_header with __packedAndy Shevchenko
GCC 9.2 starts complaining about possible pointer misalignment of pointers to the unpacked (alignment=4) structures in the packed (alignment=1) ones: CC arch/x86/cpu/tangier/acpi.o arch/x86/cpu/tangier/acpi.c: In function ‘acpi_create_fadt’: arch/x86/cpu/tangier/acpi.c:22:37: warning: taking address of packed member of ‘struct acpi_fadt’ may result in an unaligned pointer value [-Waddress-of-packed-member] 22 | struct acpi_table_header *header = &(fadt->header); CC arch/x86/lib/acpi_table.o arch/x86/lib/acpi_table.c: In function ‘acpi_create_spcr’: arch/x86/lib/acpi_table.c:366:37: warning: taking address of packed member of ‘struct acpi_spcr’ may result in an unaligned pointer value [-Waddress-of-packed-member] 366 | struct acpi_table_header *header = &(spcr->header); Fix the potential issues by annotating embedded structures with __packed even though they are packed naturally. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: add GCC version number in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10usb: xhci-dwc3: Add support for dis_u2_susphy_quirkNeil Armstrong
This quirk is necessary for the Amlogic GXL SoCs otherwise the Port 2 PHY doesn't get out of suspend and U-Boot resets the board after: XHCI timeout on event type 33... cannot recover. BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()! BUG! This quirk is also handled in the dwc3 core code, but until the xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here to fix USB support on the Amlogic libretech-cc and libretech-ac board when a device is only plugged in the OTG port. Cc: Yuri Frolov <crashing.kernel@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: efi_loader: Use efi_add_conventional_memory_map()Park, Aiden
Use efi_add_conventional_memory_map() to configure EFI conventional memory properly with ram_top value. This will give 32-bit mode U-Boot proper conventional memory regions even if e820 has an entry which is greater than 32-bit address space. Signed-off-by: Aiden Park <aiden.park@intel.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> [bmeng: fixed some typos in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: show UEFI images involved in crashHeinrich Schuchardt
If a crash occurs, show the loaded UEFI images to facilitate analysis. This is an example output: => bootefi 0x1000000 Found 0 disks Hello world of bugs! Invalid Opcode (Undefined Opcode) EIP: 0010:[<06ceb06e>] EFLAGS: 00010206 Original EIP :[<fec9906e>] EAX: 00000000 EBX: 06cec000 ECX: 00000fd0 EDX: 00000001 ESI: 06ced18a EDI: 07d0fe10 EBP: 07fe27a0 ESP: 07d0fde0 DS: 0018 ES: 0018 FS: 0020 GS: 0018 SS: 0018 CR0: 00000033 CR2: 00000000 CR3: 00000000 CR4: 00000000 DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 DR6: ffff0ff0 DR7: 00000400 Stack: 0x07d0fde8 : 0x00000000 0x07d0fde4 : 0x06ced040 --->0x07d0fde0 : 0x07fe27a0 0x07d0fddc : 0x00010206 0x07d0fdd8 : 0x00000010 0x07d0fdd4 : 0x06ceb06e UEFI image [0x06cea000:0x06cf0fff] pc=0x106e '/bug-i386.efi' ### ERROR ### Please RESET the board ### With the additional information provided by this patch we know that the problem occurred 0x106e after the load address of bug-i386.efi. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10doc: slimbootloader: Update Linux booting steps on QEMUPark, Aiden
Add steps to test Linux booting on QEMU with Yocto image. Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10x86: qemu: Report high memory in the E820 tableBin Meng
Now that we are able to get the size of high memory from QEMU, report its memory range as usable ram. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Aiden Park <aiden.park@intel.com>
2019-09-10x86: qemu: Support getting high memory sizeBin Meng
At present only size of memory that is below 4GiB is retrieved from QEMU. Add a function that gets size of memory that is above 4GiB. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Aiden Park <aiden.park@intel.com>
2019-09-10x86: qemu: Extract getting memory size to a separate routineBin Meng
This extracts getting memory size logic in dram_init() to a separate routine qemu_get_low_memory_size(). No functional changes. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Aiden Park <aiden.park@intel.com>
2019-09-10x86: Drop weak version board_get_usable_ram_top()Bin Meng
Every x86 platform provides board_get_usable_ram_top(), hence there is no need to provide a weak version board_get_usable_ram_top(), not to mention there is another weak version board_get_usable_ram_top() in common/board_f.c. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Aiden Park <aiden.park@intel.com>
2019-09-10x86: acpi: Slightly reduce binary size of ACPI tables for TangierAndy Shevchenko
Using ACPI predefined macros, such as Zero or One, will reduce a binary size of resulting ACPI tables. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: manually fixed the conflicts when applying] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-10tools: Add ifwitool to .gitignoreAndy Shevchenko
Follow up fix to the commit 56bf4f863075 ("x86: Add ifwitool for Intel Integrated Firmware Image") in order to ignore created binary. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-09arm: ti: Add missing "=" from previous fixTom Rini
While the original patch to fix a regression in distro boot for mmc on these platforms had the correct syntax, I broke the change while applying. Add back in the missing "=" here so that the syntax is correct. Reported-by: Andre Heider <a.heider@gmail.com> Fixes: 27e0f3bcf075 ("arm: ti: Fix regression in distro boot for mmc") Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-09efi_loader: check parameters EFI_FILE_PROTOCOL.GetInfo()Heinrich Schuchardt
Check the parameters of EFI_FILE_PROTOCOL.GetInfo() to avoid possible NULL dereference. Check the buffer size for EFI_FILE_SYSTEM_INFO. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: volume name in EFI_FILE_PROTOCOL.GetInfo()Heinrich Schuchardt
We cannot determine the volume name in U-Boot. Instead of providing a dummy volume name in case of EFI_FILE_SYSTEM_INFO and EFI_UNSUPPORTED in case of EFI_FILE_SYSTEM_VOLUME_LABEL consistently return an empty string. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: EFI_FILE_PROTOCOL rev 2 stubHeinrich Schuchardt
The UEFI specification requires to implement version 2 of the EFI_FILE_PROTOCOL. Provide the missing functions as stubs. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: file size checksHeinrich Schuchardt
The file size has to be determined in multiple places. Factor out a common function. If on entry into EFI_FILE_PROTOCOL.Read() the current position is beyond the end of the file, return EFI_DEVICE_ERROR. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: correct reading of directoriesHeinrich Schuchardt
EFI_FILE_PROTOCOL.Read() is used both to read files and directories. When reaching the end of a directory we always have to return buffer size zero irrespective of the incoming buffer size. (The described scenario for a Shim quirk cannot arise because every directory has at least '.' and '..' as entries.) Even when the buffer_size is too small multiple times we have to keep a reference to our last read directory entry. When we return to the start of the directory via SetPosition() we must remove the reference to a previously kept directory entry. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: eliminate inline function ascii2unicode()Heinrich Schuchardt
ascii2unicode() can only convert characters 0x00-0x7f from UTF-8 to UTF-16. Use utf8_utf16_strcpy() instead. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-09efi_loader: EFI_FILE_PROTOCOL.Write() check argsHeinrich Schuchardt
Check the parameters passed to Write(): * cannot write to directories (UEFI SCT 2017, 5.7.3.5.15) * cannot write to file opened read only (UEFI SCT 2017, 5.7.3.5.16) Add missing comments. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-09-08Merge tag 'mmc-9-6-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
Bug fixes to mmc_spi Add Aspeed SD driver Fix dw_mmc timeout calculation Fix timeout values passed to mmc_wait_dat0 sdhci dt caps/mask update [trini: Fix evb-ast2500_defconfig CONFIG_MMC line] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-07Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Initial DM conversion
2019-09-06Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-bootTom Rini
- fix mailbox status register used for polling - fix bcm2835_sdhost to wait long enough for a transfer to complete - increase kernel image size from 8 MB to 64 MB on arm64 - add support for RPi4 - add prefixes for raspberry pi related stuff to git-mailrc
2019-09-06git-mailrc: Add rpi and bcm283x maintainerAndrei Gherzan
Add entries for bcm283x and rpi prefix. Signed-off-by: Andrei Gherzan <andrei@balena.io> [mb: add commit message] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-06RPI: Add memory map for bcm2711Andrei Gherzan
Define the memory map for the BCM2711 based on the dt configuration available in the Raspberry Pi kernel fork. Signed-off-by: Andrei Gherzan <andrei@balena.io> [mb: BCM2838 -> BCM2711] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-06mmc: bcm283x: Add support for bcm2711 device in bcm2835_sdhciMatthias Brugger
The bcm2711 has two emmc controllers. The difference is the clocks they use. Add support for the second emmc controller. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Andrei Gherzan <andrei@balena.io>
generated by cgit (git 2.34.1) at 2024-12-28 21:08:57 +0000