| Age | Commit message (Collapse) | Author |
|---|
|
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
When compiling with CONFIG_SPL_SERIAL=n, gcc warns about
mbus_configure_port not being marked as static:
In file included from include/common.h:34,
from arch/arm/mach-sunxi/dram_sunxi_dw.c:11:
include/log.h:185:4: warning: 'printf' is static but used in inline function 'mbus_configure_port' which is not static
185 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
include/log.h:192:2: note: in expansion of macro 'debug_cond'
192 | debug_cond(_DEBUG, fmt, ##args)
| ^~~~~~~~~~
arch/arm/mach-sunxi/dram_sunxi_dw.c:100:2: note: in expansion of macro 'debug'
100 | debug("MBUS port %d cfg0 %08x cfg1 %08x\n", port, cfg0, cfg1);
| ^~~~~
Fix this by updating the function accordingly.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
H6 SOC needs additional initialization of PHY registers. Corresponding
changes can be found in the kernel patch [1].
Without this changes there is no enumeration of 'musb' gadget.
[1] - https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ae409cc7c3cdb9ac4a1dba3eae70efec3d6b6c79
Fixes: 35fa673e0e5f ("sunxi: phy: Add USB PHY support for Allwinner H6")
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
- r2dplus fixes
|
|
- ehci-mx6, eth/r8152 bugfixes
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-dm
Patman changelog enhancements
Sandbox SPI flash doc update
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-i2c
i2c changes for v2020.07-rc4
- fix eeprom issue with AT24MAC402 (address != 0)
- fix in i2c-uclass.c when compiling compiling with -Wtype-limits
- designware_i2c: small fixes:
- check if the device is powered
- tidy up use of NULL priv
|
|
This patch adds or modifies functional tests for the Cover-changes,
Commit-changes, and Series-process-log tags in order to account for new
behavior added in the previous few patches. The '(no changes since v1)'
case is not tested for, since that would need an additional commit to test
in addition to testing the existing code paths.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds support to multi-line changes. That is, if one has a line
in a changelog like
- Do a thing but
it spans multiple lines
Using Series-process-log sort would sort as if those lines were unrelated.
With this patch, any change line starting with whitespace will be
considered part of the change before it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
By default patman generates a combined changelog for the cover letter. This
may not always be desirable.
Many patches may have the same changes. These can be coalesced with
"Series-process-log: uniq", but this is imperfect. Similar changes like
"Move foo to patch 7" will not be merged with the similar "Move foo to this
patch from patch 6".
Changes may not make sense outside of the patch they are written for. For
example, a change line of "Add check for bar" does not make sense outside
of the context in which bar might be checked for. Some changes like "New"
or "Lint" may be repeated many times throughout different change logs, but
carry no useful information in a summary.
Lastly, I like to summarize the broad strokes of the changes I have made in
the cover letter, while documenting all the details in the appropriate
patches. I think this makes it easier to get a good feel for what has
changed, without making it difficult to wade through every change in the
whole series.
This patch adds two new tags to add changelog entries which only appear in
the cover letter, or only appear in the commit. Changes documented with
"Commit-changes" will only appear in the commit, and will not appear in the
cover letter. Changes documented with "Cover-changes" will not appear in
any commit, and will only appear in the cover letter.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Patman outputs a line for every edition of the series in every patch,
regardless of whether any changes were made. This can result in many
redundant lines in patch changelogs, especially when a patch did not exist
before a certain revision. For example, the existing behaviour could result
in a changelog of
Changes in v7: None
Changes in v6: None
Changes in v5:
- Make a change
Changes in v4: None
Changes in v3:
- New
Changes in v2: None
With this patch applied and with --no-empty-changes, the same patch would
look like
(no changes since v5)
Changes in v5:
- Make a change
Changes in v3:
- New
This is entirely aesthetic, but I think it reduces clutter, especially for
patches added later on in a series.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Some mailing lists have size limits and when we add binary contents
to our patches it's easy to exceed the size limits.
Git supports a command line option "--no-binary" to generate patches
without any binary contents. Add an option in patman to handle this.
Note with this option patches cannot be applied properly, but they
are still useful for code review.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Sort the existing command line options by:
- help comes first
- option starts with '-'
- option starts with '--'
Lower case followed by upper case letters, in alphabetical order.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Including the assembler headers before including common.h etc leads to
compilation errors upon MIPS64 based platforms using OF_LIVE. This
patch reorders the include files to the "correct" oder.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Since the commit 1289e96797bf ("sandbox: spi: Drop command-line SPI
option"), "--spi_sf" command line option is no longer supported.
So update the following documents to sync them up with the change.
doc/arch/sandbox.rst
doc/SPI/README.sandbox-spi
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As we discussed in [1], this option is not needed for sandbox build.
[1] https://lists.denx.de/pipermail/u-boot/2020-February/400182.html
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Enable richer HUSH shell to make working with the board more pleasant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The board_eth_init() is not used for DM case, enable it only for
the non-DM case. This function should eventually be removed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Although I think it never occurs, the code doesn't make sense, because
it may allow to assign an IN endpoint to ss->ep_out.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Finally enable config to support HDMI console output in VIM3 boards
- Fix USB gadget support for libretech-ac/pc & vim/vim2 boards
|
|
The khadas-vim, khadas-vim2, libretech-ac & libretech-*-pc boards were missing
DT tweak to enable USB gadget.
Add them to their -u-boot.dtsi files and include the right gxl-u-boot.dtsi.
Fixes: a19e8a0f03 ("arm: dts: meson-gxl: Add USB Gadget nodes for U-Boot")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Enable options to permit HDMI output on Khadas VIM3 & VIM3L boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
output
Include the common g12 u-boot tweaks to permit enabling video output tweaks
on Khadas VIM3 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Because of this commit :
5ae84860b0 ("misc: i2c_eeprom: verify that the chip is functional at probe()")
at probe time, each eeprom is tested for read at offset 0.
The Atmel AT24MAC402 eeprom has different mapping. One i2c slave address is
used for the lower 0x80 bytes and another i2c slave address is used for the
upper 0x80 bytes. Because of this basically the i2c master sees 2 different
slaves. We need the upper bytes because we read the unique MAC address from
this EEPROM area.
However this implies that our slave address will return error on reads
from address 0x0 to 0x80.
To solve this, implemented an offset field inside platform data that is by
default 0 (as it is used now), but can be changed in the compatible table.
The probe function will now read at this offset and use it, instead of blindly
checking offset 0.
This will fix the regression noticed on these EEPROMs since the commit
abovementioned that introduces the probe failed issue.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
When compiling with -Wtype-limits we see this error:
drivers/i2c/i2c-uclass.c: In function ‘i2c_deblock_gpio_loop’:
drivers/i2c/i2c-uclass.c:517:21: error: comparison of
unsigned expression >= 0 is always true [-Werror=type-limits]
517 | while (scl_count-- >= 0) {
|
Don't loop forever.
Fixes: 1f746a2c82b1 ("i2c: Make deblock delay and SCL clock configurable")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
If the device doesn't return a version that means the device is
non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare databook. It also matches what the
Picasso PPR says.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested on chromebook_coral:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present we still have pre-driver-model code in this driver and it makes
things a bit confusing. In particular calc_bus_speed() is called with priv
as NULL if not using driver model.
This results in spk_cnt and comp_param1 being read from an invalid address
if not using driver model. For comp_param1 this may not cause problems if
reading from addresses close to 0 happens to be allowed, as high speed is
only supported by DM code. But spk_cnt is subsequently used to calculate
the bus periods and so this may cause problems (e.g. on spear600 board
which has not been migrated yet).
Add a new parameter regs parameter to calc_bus_speed() and add more
comments to this function and to _dw_i2c_set_bus_speed(), which calls it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
- Fix SPI boot on ds414 (Ezra)
- Fix PHY mode definition on armada-3720-uDPU (Jakov)
- Convert CRS305-1G-4S to generic version (Luka)
|
|
- Use device tree for FSP-M and FSP-S configuration on Intel Apollo Lake
- Add SMBIOS cbmem entry parsing for coreboot
- Various clean-ups to CBFS implementation
|
|
The size is not actually used since it is present in the header. Drop this
parameter. Also tidy up error handling while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Currently we support reading a file from CBFS given the address of the end
of the ROM. Sometimes we only know the start of the CBFS. Add a function
to find a file given that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This function currently returns a node pointer so there is no way to know
the error code. Also it uses data in BSS which seems unnecessary since the
caller might prefer to use a local variable.
Update the function and split its body out into a separate function so we
can use it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We may as well return the error code and use it directly in the command
code. CBFS still uses its own error enum which we may be able to remove,
but leave it for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The start address of the CBFS is used when scanning for files. It makes
sense to put this in our cbfs_priv struct and calculate it when we read
the header.
Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It doesn't make sense to use u8 * as the pointer type for accessing the
CBFS since we do not access it as bytes, but via structures. Change it to
void *, which allows us to avoid a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
These two functions have mostly the same code. Pull this out into a common
function.
Also make this function zero the private data so that callers don't have
to do it. Finally, update cbfs_load_header_ptr() to take the base of the
ROM as its parameter, which makes more sense than passing the address of
the header within the ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This function is strange at the moment in that it takes a header pointer
but then accesses the cbfs_s global. Currently clients have their own priv
pointer, so update the function to take that as a parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This function is strange at the moment in that it takes a header pointer
but then accesses the cbfs_s global. Currently clients have their own priv
pointer, so update the function to take that as a parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present this uses a true return to indicate it found a file. Adjust it
to use 0 for this, so it is consistent with other functions.
Update its callers accordingly and add a check for malloc() failure in
file_cbfs_fill_cache().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present this uses an int type. U-Boot now supports bool so use this
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
U-Boot uses ulong for addresses but there are a few places in this driver
that don't use it. Convert this driver over to follow this convention
fully.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present the result variable in the cbfs_priv is called 'result' as is
the local variable in a few functions. Change the latter to 'ret' which is
more common in U-Boot and avoids confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It is not definded anywhere.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.gpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
A the moment the FSP-S configuration is a mix of hard coded values and
devicetree properties.
This patch makes FSP-S full configurable from devicetree by
adding binding properties for all FSP-S parameters.
Co-developed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
A the moment the FSP-M configuration is a mix of hard coded values and
devicetree properties.
This patch makes FSP-M full configurable from devicetree by adding
binding properties for all FSP-M parameters.
Co-developed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
[sjg: Fix a build error for coral]
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Add __maybe_unused to fsp_update_config_from_dtb()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Only load VBT if it's present in the u-boot.rom.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We don't need to print this information since it is shown when the MTRRs
are displayed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
