summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-08arm64: versal: Enable memory mapping via DTMichal Simek
Code reads DT and setup MMU table based on memory node. This will ensure that only DT needs to be changed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Set initrd_high to as high as possibleT Karthik Reddy
This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Set initrd_high to as high as possibleSiva Durga Prasad Paladugu
This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: fpga: Add PL bit stream load supportSiva Durga Prasad Paladugu
This patch adds PL bitstream load support for Versal platform. The PL bitstream is loaded by making an SMC to ATF which in turn communicates with platform firmware which configures and loads PL bitstream on to PL. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Also record versal name to versal fragmentMichal Simek
Just to make sure that also drivers with versal name are assigned to proper fragment. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Define board_late_init for versalSiva Durga Prasad Paladugu
Define board_late_init which performs bootmode detection and prepares corresponding distro boot commaand sequence. Also disable it for mini platforms because simply there is no need to have it enabled. But also disable it for virtual platform because Qemu is not modelling this register space that's why travis testing would fail. This configuration should be reverted when mainline Qemu is updated. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Enable SPI support in SPL for zcu104Michal Simek
It is enabling this mode but full boot is not validated yet. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add u-boot,dm-pre-reloc to clk300 nodeMichal Simek
This node is used by qspi driver for supporting qspi boot mode in SPL. Similar changes have beeen done by commit a9022b017a90 ("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Enable gpio hog support for zcu102Michal Simek
Gpio hogs are used for GT mux setup after power up. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08xilinx: Add sd boot command script for referenceSiva Durga Prasad Paladugu
This patch adds sdboot command script for reference. This can be converetd into uboot script using mkimage and use for booting. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08xilinx: Add qspi boot command script for referenceSiva Durga Prasad Paladugu
Thsi patch adds qspiboot command script for reference. This can be converetd into uboot script using mkimage and use for booting. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Define default SPL_TEXT_BASE address in KconfigMichal Simek
Define default address via Kconfig. There is no need to change this address for most of the boards but it is also possible. This one line save a lot of lines in defconfigs that's why make sense to do it. The similar change has been done by commit 9340d8fe8beb ("sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2019-10-07Prepare v2019.10Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-07NET: DW: fix regression for ARC boardsEugeniy Paltsev
The commit 642b80d256e ("net: designware: drop compatible altr, socfpga-stmmac") breaks designware ethernet for all ARC boards. It removes "altr, socfpga-stmmac" compatible from "drivers/net/designware.c" without changing compatible in the boards which use it. Fix that by adding "snps,arc-dwmac-3.70a" compatible string to "drivers/net/designware.c" and using it in ARC boards device tree. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
2019-10-06Merge branch '2019-10-06-master-imports'Tom Rini
- Regression work-around on SoCFPGA by disabling WDT in some cases. - Fix seg fault on 'host info' in some cases.
2019-10-06cmd: host: fix seg fault at "host info"AKASHI Takahiro
With the patch below applied, host_block_dev structure was switched to be placed in platdata rather than priv. The command "host info" must be aligned with this change. Otherwise, we will see "Segmentation Fault." Fixes: 8f994c860d91 ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-06MAINTAINERS: Update my email addressMaxime Ripard
I'm not at bootlin anymore, and my mail address doesn't work any longer. Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-06arm: socfpga: disable CONFIG_SPL_WDT for gen5 and a10Simon Goldschmidt
These boards don't have a watchdog enabled in SPL, so make sure CONFIG_SPL_WDT is not enabled. Fixes: commit 6874cb72204f ("watchdog: Split WDT from SPL_WDT") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-06gitlab-ci: fix typo 'plaforms'Heinrich Schuchardt
%s/plaforms/platforms/g Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-05Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulator
2019-10-04Merge branch '2019-10-04-master-imports'Tom Rini
- Assorted TI platform fixes - Revert the change that broke environment flag validation - Assorted typo fixes - Assorted Kconfig dependency fixes - Other minor bug fixes
2019-10-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- dm: core: Correct low cell in ofnode_read_pci_addr() - dm: core: Correct bad cast in ofnode_get_addr_size_index()
2019-10-04Revert "env: solve compilation error in SPL"Tom Rini
This reverts commit 7d4776545b0f8a8827e5d061206faf61c9ba6ea9. The changes here break environment validation and furthermore do not seem to be required. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-04ARM: dts: imx6q-logicpd: Add missing imx6q-logicpd-u-boot for SPLAdam Ford
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file which will enable these functions so SPL can properly setup UART, detect microSD card, and startup. Fixes: 8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled, remove MMC init") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-10-04initcall.h: initcall_run_list(): Improve debug outputOvidiu Panait
Existing debug output is mixed with the function name: initcall_run_list() initcall: 25263initcall_run_list() (relocated to 425263) Turn it to: initcall_run_list() initcall: 25263 (relocated to 425263) Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
2019-10-04Kconfig: fix a typo in the description of bmp command.Andrius Štikonas
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
2019-10-04Kconfig: Migrate CONFIG_BOOTM_* optionsTom Rini
Migrate all of the existing OS support options that are under CONFIG_BOOTM_* to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-04cmd: part: number: return hexadecimal valueRoman Stratiienko
At this point we are using part number sub-command to retrieve UUID of the partition using it's name. e.g.: part number mmc $mmcdev system_a system_a_index part uuid mmc $mmcdev:${system_a_index} system_a_uuid Since 'part uuid' sub-command expects partition index in hex format and 'part number' returns decimal value, 'part uuid' command will provide wrong UUID or fail. Fixes: be683756f62034 ("cmd: part: Add 'number' sub-command") Cc: Dirk Behme <dirk.behme@de.bosch.com> Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com> Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-10-04ARM: keystone2: update the default addresses of the secure monitorJean-Jacques Hiblot
To accommodate the growth of u-boot, we need to shift the location of the secure monitor. Moving it 64kB further. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-04board: ti: am654: Disable TRNG node for HS devicesAndrew F. Davis
On HS devices the access to TRNG is restricted on the non-secure ARM side, disable the node in DT to prevent firewall violations. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-04autoboot: add necessary dependency at AUTOBOOT_MENU_SHOWAKASHI Takahiro
Otherwise, menu_show() will be undefined in bootdelay_process(). Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2019-10-04MAINTAINERS, git-mailrc: Update the maintainer for socfpgaLey Foon Tan
This updates MAINTAINERS and git-mailrc to add me as maintainer for socfpga. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Acked-by: Marek Vasut <marex@denx.de>
2019-10-04Makefile: mrproper should remove *.pyc filesHeinrich Schuchardt
*.pyc files contain compiled Python bytecode. 'make mrproper' should remove them. Removing *.pyc files helps for instance sometimes when running into an error "binman: Unknown entry type 'blob' in node '/binman/blob'". Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-04Makefile: Fix typo around CONFIG_SPL_FIT_SOURCEMichal Simek
Trivial fix. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-04arm: K3: Increase default SYSFW image size allocationAndrew F. Davis
The memory allocated to store the FIT image containing SYSFW and board configuration data is statically defined to the largest size expected. This was 269000 bytes but now needs to be grown to 276000 to make room for the signatures attached to the board configuration data on High Security devices. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-10-03dm: core: Correct bad cast in ofnode_get_addr_size_index()Simon Glass
At present this code passes an fdt_addr_t pointer as a u64 pointer which is not safe, since sizeof(fdt_addr_t) may be 4, e.g. with sandbox. Correct this to avoid a stack corruption problem. Fixes: e679d03b08 (core: ofnode: Add ofnode_get_addr_size_index) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: correct one typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-03dm: core: Correct low cell in ofnode_read_pci_addr()Simon Glass
This reads the low cell of the PCI address from the wrong cell. Fix it. Also fix the function that this code came from. Fixes: 9e51204527 (dm: core: Add operations on device tree references) Fixes: 4ea5243a3a (fdt: fix fdtdec_get_pci_addr() for CONFIG_PHYS_64BIT) Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-01Merge tag 'rpi-next-2019.10.2' of https://github.com/mbgg/u-bootTom Rini
RPi4: Fix amount of memory seen by the kernel.
2019-10-01Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Propagate acpi_rsdp_addr to x86 kernel via boot parameters
2019-10-01x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parametersAndy Shevchenko
This is reincarnation of the U-Boot commit 3469bf4274540d1491d58e878a9edc0bdcba17ac Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Date: Wed Jan 10 19:40:15 2018 +0200 x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters after upstream got eventually the Linux kernel commit e6e094e053af75cbc164e950814d3d084fb1e698 Author: Juergen Gross <jgross@suse.com> Date: Tue Nov 20 08:25:29 2018 +0100 x86/acpi, x86/boot: Take RSDP address from boot params if available Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-01rpi4: enable dram bank initializationMatthias Brugger
When booting through the efi stub, the memory map get's created by reading the dram bank information. Depending on the version of the RPi4 this information changes. Read the device tree to initialize the dram bank data structure. This way the kernel is able to access the whole range of available memory. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-30Merge tag 'u-boot-atmel-fixes-2019.10-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel fixes for 2019.10 cycle: This includes only tiny cleanups on env changes related to 2019.10 new features: removal of duplicate env settings (otherwise there may be warnings in building..) and a small fix for flashes on Gardena smart gateway (requires nand bad block tables).
2019-09-30Merge tag 'u-boot-rockchip-20190928' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fix efuse read data number for rk3399 - make_fit_atf.py: fix .its generation for a single atf image
2019-09-30at91: configs: Drop duplication of defconfig macrosTudor Ambarus
'commit a9221f3ebd6d ("at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs")' migrated CONFIG_ENV_ macros to defconfigs but did not remove the identical redefinition of these macros in include/configs/. Since the duplicated macros have the same value as the ones in defconfigs, no "redefined" warnings were raised. Remove duplicated macros for all sama5 and sam9x5ek boards. While verifying that the removal of the macros from include/configs did not change the same macros in defconfigs, overwrite the old defconfig by saving them with the output from "make arch=ARM savedefconfig". This resulted in the movement of some macros in the defconfig files. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-09-30arm: at91: gardena-smart-gateway-at91sam: Enable CONFIG_SYS_NAND_USE_FLASH_BBTStefan Roese
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart Gateway. This is especially important, since the Linux driver also enables this option and uses the BBT table pages. Without setting this option, U-Boot will try to re-use these pages again (e.g. UBI). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Tom Rini <trini@konsulko.com>
2019-09-30ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulatorMarek Vasut
This patch restores commit c49d0ac38a76 ("ARM: dts: rmobile: Increase off-on delay on the SD Vcc regulator"), which was accidentally dropped during DT resync in commit 317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0"). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Fixes: 317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
2019-09-28rockchip: make_fit_atf.py: fix .its generation for a single atf imageHeiko Stuebner
The commit 619f002db864 ("rockchip: make_fit_atf.py: fix loadables property set error") fixed the double-loading of the primary atf-image, but didn't take into account that there may be rare atf images with only that main section present. Right now this will result in a broken its due to the loadables section not getting closed correctly, so fix that by adapting the guards around the loop. The guards now protect against 0 segments when the bl31 binary doesn't contain any section and 1 segment when only a core atf section is present. Fixes: 619f002db864 ("rockchip: make_fit_atf.py: fix loadables property set error") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-28rockchip: misc: read the correct number of bytes from the efuseHeiko Stuebner
Originally the cpuid var the value gets read into was defined as u8 cpuid[RK3399_CPUID_LEN]; hence the sizeof(cpuid) would return the correct the correct number of array elements. With the move to a separate function cpuid becomes a pointer and sizeof(cpuid) hence returns the pointer size - 8 in the arm64 case. We do have the actual id length available as function param so use it for actual amount of bytes to read. Fixes: 04825384999f ("rockchip: rk3399: derive ethaddr from cpuid") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-26Merge tag 'efi-2019-10-rc5' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for v2019.10-rc5 Bug fixes for the SetVariable() boot service.
2019-09-24ci: add envtools supportPierre-Jean Texier
This commit add envtools suppport to CI to verify if there is no build issues. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-26 15:00:36 +0000