summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-06-24net: xilinx: axi_emac: Fix endless loop when no PHYs are connectedPatrick van Gelder
The index used to iterate over the possible PHYs in axiemac_phy_init was an unsigned int and decremented. Therefor it was always >= 0 and never exited the loop. Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24doc: board: xilinx: zynq.rst: add description how to flash a SD cardJohannes Krottmayer
Add a short description in the ZYNQ documentation how to prepare a SD card and copy the related images to SD card. Signed-off-by: Johannes Krottmayer <krjdev@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: xilinx: Print fpga error value in hexT Karthik Reddy
Fpga returns error value when fails, error status should be printed in hex format. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24spi: zynq_[q]spi: Convert config's to macro'sAshok Reddy Soma
Remove below config options and convert them to macros. They have never been configured to different values than default one. And also it makes sense to reduce the config_whitelist. CONFIG_SYS_ZYNQ_SPI_WAIT CONFIG_SYS_ZYNQ_QSPI_WAIT CONFIG_XILINX_SPI_IDLE_VAL Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24net: gem: Disable PCS autonegotiation in case of fixed-linkMichal Simek
Disable PCS autonegotiation if fixed-link node is present in device tree. This way systems with multiple GEM instances with a combination of SGMII-fixed and SGMII-PHY will work. Reported-by: Goran Marinkovic <goran.marinkovic@psi.ch> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: zynqmp: Change spi-max-frequency for qspi miniT Karthik Reddy
Change mini u-boot qspi spi-max-frequency to 108Mhz, make the frequency similar to full u-boot qspi flash spi-max-frequency. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: zynqmp: Fix si570 clock output names and referencesSaeed Nowshadi
Align clock output names with node references. Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: zynqmp: Reduce console buffer sizeT Karthik Reddy
Reduce console buffer size to 1kbyte to accommodate memory allocations in mini u-boot for zynqmp. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: versal: Enable config to map TCM and OCMAshok Reddy Soma
Enable CONFIG_DEFINE_TCM_OCM_MMAP to map TCM and OCM memory. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm: zynq: Enable alternative memory testAshok Reddy Soma
Enable alternative memory test for zynq platforms. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24fpga: zynqpl: Add zynq aes load & loadp commandsT Karthik Reddy
Added support for zynq aes load & loadp commands. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24fpga: zynqpl: Flush dcache only for non-bitstream dataT Karthik Reddy
In case of aes decryption destination address range must be flushed before transferring decrypted data to destination. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24fpga: zynqpl: Check if aes engine is enabledIbai Erkiaga
AES engine cannot be used if has not been enabled at boot time with an encrypted boot image. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24fpga: zynqpl: Check fpga config completionT Karthik Reddy
This patch checks fpga config completion when a bitstream is loaded into PL. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24fpga: zynqpl: Correct PL bitstream loading sequence for zynqaesSiva Durga Prasad Paladugu
Correct the PL bitstream loading sequence for zynqaes command by clearing the loaded PL bitstream before loading the new encrypted bitstream using the zynq aes command. This was done by setting the PROG_B same as in case of fpgaload commands. This patch fixes the issue of loading the encrypted PL bitstream onto the PL in which a bitstream has already been loaded successfully. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24firmware: zynqmp: Change panic logic in zynqmp_pmufw_load_config_object()Michal Simek
There is no need to panic all the time when pmufw config object loading failed. The patch improves function logic to report permission deny case and also panic only for SPL case. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-24clk: versal: Remove alt_ref_clk from clock sourcesRajan Vaja
alt_ref_clk is applicable only for PS extended version. For PS base version there is no separate alt_ref_clk. It is tied with ref_clk, so remove it from driver. Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm64: versal: Let U-Boot to update memory node by defaultMichal Simek
There is no reason not to let U-Boot to update memory node by default. In past this was disabled by purpose to be able to test different memory configurations from one U-Boot instance. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24mmc: zynq_sdhci: Remove global pointerMichal Simek
Driver is not calling gd anywhere that's why there is not need to define it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-24arm: versal: Fix xspi0 boot modeMichal Simek
Use proper number to be aligned with xspi0 boot mode. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-06-23Merge tag 'u-boot-imx-20200623' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.07 ----------------- Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/701059103 - Fixes for atheros and cubox - Toradex: mostly environment - i.MX7: DDR fixes - switch to DM - sabrelite : fix MMC access
2020-06-23configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-22Prepare v2020.07-rc5Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-23mx6cuboxi: remove unused codeWalter Lozano
After enabling SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC the MMC initialization code is not longer needed. This patch removes the unused code. Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23mx6cuboxi: enable OF_CONTROL and DM in SPLWalter Lozano
In order to take the beneficts of DT and DM in SPL, like reusing the code and avoid redundancy, enable SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC. With this new configuration SPL image is 50 KB, higher than the 38 KB from the previous version, but it still under the 68 KB limit. Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23mx6cuboxi: customize board_boot_order to access eMMCWalter Lozano
In SPL legacy code only one MMC device is created, based on BOOT_CFG register, which can be either SD or eMMC. In this context board_boot_order return always MMC1 when configure to boot from SD/eMMC. After switching to DM both SD and eMMC devices are created based on the information available on DT, but as board_boot_order only returns MMC1 is not possible to boot from eMMC. This patch customizes board_boot_order taking into account BOOT_CFG register to point to correct MMC1 / MMC2 device. Additionally, handle IO mux for the desired boot device. Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23mx6cuboxi: enable MMC and eMMC in DT for SPLWalter Lozano
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
2020-06-23mx6ull_14x14_evk_plugin: Convert to DM_ETHFabio Estevam
Convert to DM_ETH to avoid board removal from the project. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-23mx6slevk_spl: Convert to DM_ETHFabio Estevam
Convert to DM_ETH to avoid board removal from the project. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-23mx6slevk_spinor: Convert to DM_ETHFabio Estevam
Convert to DM_ETH to avoid board removal from the project. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-23arm: dts: imx: fsl-imx8qm.dtsi: fix gpio aliasesYe Li
Current aliases missed gpio0 node, and this node shoud be aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we will get below message when running "gpio status" command, and see the reason by "dm uclass". => gpio status Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000' Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000' Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000' => dm uclass uclass 36: gpio 0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1) 1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0) 2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1) 3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2) 4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3) 5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4) 6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5) 7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6) Signed-off-by: Ye Li <ye.li@nxp.com>
2020-06-23gpio: mxc_gpio: change gpio index for i.MX8Ye Li
Since the i.MX8 GPIO banks are indexed from 0 not 1 on other i.MX platforms, so we have to adjust the index accordingly. Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
2020-06-23mx6ul_14x14_evk: Avoid overlap of environment over U-Boot properOtavio Salvador
We need to change the environment offset to avoid corrupting the U-Boot binary when saving it. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-06-23mx6ul_14x14_evk: Enable SPL USB and SDP supportOtavio Salvador
This fixes the boot from USB loader, which is critical to easy the manufacture process. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-06-22ARM: imx: soc: Select default TEXT_BASE for MX7Marek Vasut
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot text base is picked as the one used by various MX7 boards. The SPL text base however is different. The SPL text base is set to 0x912000 instead of the usual 0x911000, that is because the 0x911000 value cannot work. Using 0x911000 as a SPL text base will result in the DCD header being placed below the 0x911000 address, which is a reserved SRAM area which must not be used. This will actually trigger eMMC boot failure on MX7D at least. Hence the increment. Update all boards affected by this SPL problem to the new SPL_TEXT_BASE. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-22ARM: imx: soc: Switch BOARD_EARLY_INIT_F to imply on MX7Marek Vasut
There are systems where board_early_init_f() is plain empty. Switch the config option from "select" to "imply", to permit user to unset the BOARD_EARLY_INIT_F if it were to be empty. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-22ARM: imx: ddr: Fill in missing DDRC ZQCTLx on i.MX7Marek Vasut
The iMX7 defines further DDRC ZQCTLx registers, however those were thus far missing from the list of registers and not programmed. On systems with LPDDR2 or DDR3, those registers must be programmed with correct values, otherwise the DRAM may not work. However, existing systems which worked without programming these registers before are now setting those registers to 0, which is the default value, so no functional change there. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-22imx: imx8qm_rom7720_a1: update READMEOliver Graute
Update README to extract firmware from scripts Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
2020-06-22ARM: imx6: Fetch MAC address in board_init_late() on DH iMX6 PDK2Marek Vasut
This is needed to obtain the MAC from EEPROM/OTP only after the final env is populated, otherwise the ethaddr might be overriden. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Claudius Heine <ch@denx.de> Cc: Harald Seiler <hws@denx.de> Cc: Ludwig Zenz <lzenz@dh-electronics.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-22arm: wandboard: move CONFIG_MXC_UART to defconfigHeinrich Schuchardt
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in the .config file. To avoid duplicate definitions move the setting from include/configs/wandboard.h to configs/wandboard_defconfig. Document the debug UART settings in the README. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-06-22Fix MMC access on SabreliteMartyn Welch
It appears that MMC access on the Sabrelite has been broken since cdcaee9518: Loading Environment from MMC... Card did not respond to voltage select! *** Warning - No block device, using default environment Remove the board_mmc_init() and related entries now that we should be using DM_MMC, add PINCTRL so that things work as expected. Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Tested-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
2020-06-22colibri_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22colibri_imx7: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22apalis_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22toradex: imx: enable BOOTCOUNT featureIgor Opaniuk
This introduces automatic boot counter that increases after every reset.After a power-on reset, it will be initialized with 1, and each reboot will increment the value by 1. By default it's disabled if bootlimit isn't set. To enable this feature you have set bootcount limit ("bootlimit"), alternate boot action ("altbootcmd") that will be performed if the new value of bootcount exceeds the value of bootlimit, and "upgrade_available" to let U-Boot automatically increase and save the counter value after every reset: > setenv bootlimit 5 > setenv upgrade_available 1 > setenv altbootcmd "bootm ..." In case the bootlimit exceeds, the message will be shown and albootcmd executed: Warning: Bootlimit (5) exceeded. Using altbootcmd. To reset bootcount run: > bootcount reset Print current value: > bootcount print Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22apalis-tk1: fix setting fdtfile valueIgor Opaniuk
s/fdt-module/fdt_module/g, as we don't use dash in fdt_file anymore. Fixes: 4c63a601("apalis-tk1: support v1.2 hardware revision") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22apalis-tk1: enable distrobootIgor Opaniuk
1. Use distro_bootcmd as default boot command instead of legacy emmcboot wrapper. 2. Drop emmcboot and sdboot wrappers. 3. Provide proper boot order for Distro Boot. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-22configs/colibri_vf.h: drop sdboot in favour of distro_bootcmdMax Krummenacher
The distro bootscript uses kernel_image to get the file name of the kernel, so change that variable name. UBI boot has precedence in the default boot command. If one wants to boot from SD with a working NAND installation stop in U-Boot and enter: setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2020-06-22colibri_vf_defconfig: enable part cmdMax Krummenacher
This allows to boot from SD/USB with passing the rootfs partition via UUID. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2020-06-22colibri-imx6ull/imx7: define bootubipart for distro bootStefan Agner
When using distro boot to boot from UBI volumes the boot partition has been hardcoded to "UBI" (capital letters). However, our default MTD layout uses "ubi" (lower case letter). Define "ubi" as the default UBI partition for distro boot for Toradex. This allows to use distro boot without having to redefine the MTD partition layout which is useful for TorizonCore. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
generated by cgit (git 2.34.1) at 2024-12-23 20:20:25 +0000