| Age | Commit message (Collapse) | Author |
|---|
|
This patch makes sure the correct mask is applied when setting
the encryption and I2C bus 0 clock in SCCR.
Failing to do so may lead to ENCCM being 0 in which case I2C bus 0
won't function.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
Commit af1c2b84 added a generic phy support, with an ID of zero
and a 32 bit mask; meaning that it will match on any PHY ID.
The problem is that there is a test that checked if a matching
PHY was found, and if not, it printed the non-matching ID.
But since there will always be a match (on the generic PHY,
worst case), this test will never trip.
In the case of a misconfigured PHY address, or of a PHY that
isn't explicitly supported outside of the generic support,
you will never see the ID of 0xffffffff, or the ID of the
real (but unsupported) chip. It will silently fall through
onto the generic support.
This change makes that test useful again, and ensures that
the selection of generic PHY support doesn't happen without
some sort of notice. It also makes it explicitly clear that
the generic PHY must be last in the PHY table.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
|
|
Fix typo in makefile which broke out of tree builds.
Also use expolicit "rm" instead of "ln -sf" which is known to be
unreliable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This adds tsec12ioovcr to include/asm-ppc/immap_85xx.h (was reserved.)
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
|
|
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Commit e1be0d25, "32bit BUg fix for DDR2 on 8572" prevented other
sdram_cfg bits (such as ecc and self_refresh_in_sleep) from being set.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
|
|
Fix typo in makefile which broke out of tree builds.
Also use expolicit "rm" instead of "ln -sf" which is known to be
unreliable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Conflicts:
lib_ppc/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
add CONFIG_BOOTCOUNT_LIMIT feature for 8360 CPU.
The bootcounter uses 8 bytes from the muram,
because no other memory was found on this
CPU for the bootcount feature. So we must
correct the muram size in DTS before booting
Linux.
This feature is actual only implemented for
MPC8360, because not all 83xx CPU have qe,
and therefore no muram, which this feature
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
old code implemented the QE_ENET10 errata only for Silicon
Revision 2.0. New code reads now the Silicon Revision
register and sets dependend on the Silicon Revision the
values as advised in the QE_ENET10 errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
- HRCW update
HRCWH_BOOTSEQ_DISABLE not HRCWH_BOOTSEQ_NORMAL
HRCWH_LALE_EARLY added
- DDR-SDRAM settings modified. This solves sporadically
problems with this memory.
- CS1 now 128 MB window size
- CS3 now 512 MB window size
- PRAM activated
- MTDPARTS_DEFAULT defined
- CONFIG_HOSTNAME added
- MONITOR_LEN now 384 KB
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch adds I2C mux support for the fsl_i2c driver. This
allows you to add "new" i2c busses, which are reached over
i2c muxes. For more infos, please look in the README and
search for CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
In case where a board not uses CONFIG_POST, it is not
necessary to init the DTTs when running from flash.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
1. RD_TO_PRE missed to add the AL, and need min 2 clocks for
tRTP according to DDR2 JEDEC spec.
2. WRTORD - tWTR need min 2 clocks according to DDR2 JEDEC spec.
3. add the support of DDR2-533,667,800 DIMMs
4. cpo
5. make the AL to min to gain better performance.
The Micron MT9HTF6472CHY-667D1 DIMMs test passed on
MPC837xEMDS platform at 266MHz/333MHz/400MHz data rate.
items 1, 2 and 5:
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The previous version rebooted forever with DDR bigger than 256MB.
Access the DS1339 RTC chip is on I2C1 bus.
Allow DHCP.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.
Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
it is not necessary to init the DTTs so early,
so move this init to board_init_r ().
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Fix following warning while compilation for mcc200 board:
lcd.c: In function 'lcd_display_bitmap':
lcd.c:625: warning: unused variable 'cmap'
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Fixes commit 407976185e0dda2c90e89027121a1071b9c77bfb
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
|
|
The smc911x driver has a lot of useful defines/functions which can be used
by pieces of code (such as example eeprom programmers). Rather than
forcing each place to duplicate these defines/functions, split them out
of the smdc911x driver into a local header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Guennadi Liakhovetski <lg@denx.de>
CC: Magnus Lilja <lilja.magnus@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
|
|
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Add a driver for the Synchronous Display Controller and the Display
Interface on i.MX31, using IPU for DMA channel setup. So far only
displaying of bitmaps is supported, no text output.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
This patch also simplifies some ifdefs in lcd.c, introduces a generic
vidinfo_t, which new drivers are encouraged to use and old drivers to switch
over to.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
This patch adds 16bpp BMP support to the common lcd code.
Use CONFIG_BMP_16BPP and set LCD_BPP to LCD_COLOR16 to enable the code.
At the moment it's only been tested on the MIMC200 AVR32 board, but extending
this to other platforms should be a simple task !!
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
This is a driver for the S6E63D6 SPI OLED display controller from Samsung.
It only provides access to controller's registers so the client can freely
configure it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Some SPI devices have special requirements on chip-select handling.
With this patch we can use a GPIO as a chip-select and strictly follow
the SPI_XFER_BEGIN and SPI_XFER_END flags.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This is a minimal driver, so far only managing output. It will
be used by the mxc_spi.c driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Fix setting the SPI Control register, 8 and 16-bit transfers
and a wrong pointer in the free routine in the mxc_spi driver.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
We should use pci_last_busno() in pci_init_bus(), otherwise we'll
erroneously re-use PCI0's first_busno for PCI1 hoses.
NOTE: The patch is untested. All MPC83xx FSL boards I have have
PCI1 in miniPCI form, for which I don't have any cards handy.
But looking in cpu/mpc85xx/pci.c:
...
#ifdef CONFIG_MPC85XX_PCI2
hose = &pci_hose[1];
hose->first_busno = pci_hose[0].last_busno + 1;
And considering that we do the same for MPC83xx PCI-E support,
I think this patch is correct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch fixes copy-paste issue: pci_hose[0]'s first and last
busnos were used to fixup pci1's nodes.
We don't see this bug triggering only because Linux reenumerate
buses anyway.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This patch fixes an issue in config space read accessors: we should
fill-in the value even if we fail (e.g. skipping devices), otherwise
CONFIG_PCI_SCAN_SHOW reports bogus values during boot up.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Currently we assign first_busno = 0 for the first PCIe hose, but this
scheme won't work if we have ordinary PCI hose already registered (its
first_busno value is 0 too).
The old code worked fine only because we have PCI disabled on
MPC837XEMDS boards in stand-alone mode (see commit 00f7bbae92e3b13f2b3
"mpc83xx: fix PCI scan hang on the standalone MPC837xE-MDS boards").
But on MPC837XERDB boards we have PCI and PCIe, so the bug actually
triggers.
So, to fix the issue, we should use pci_last_busno() + 1 for the
first_busno (i.e. last available busno).
Reported-by: Huang Changming <Chang-Ming.Huang@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This is just a handy routine that reports last PCI busno: we walk
down all the hoses and return last hose's last_busno.
Will be used by PCI/PCIe initialization code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Currently, we get 256MB as the default, but since all the 86xx
board configs define a 2G BAT mapping for RAM, raise default
to 2G.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
If 36-bit addressing is enabled, print a message on the console
when we boot.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
|
|
|
|
NetLoop polls every cycle with getenv some environment variables.
This is horribly slow, especially when the environment is big.
This patch reads only the environment variables in NetLoop,
when they were changed.
Also moved the init part of the NetLoop function in a seperate
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
A forward port of the last version to work with the newer smc911x driver.
I only have a board with a LAN9218 part on it, so that is the only one
I've tested. But there isn't anything in this that would make it terribly
chip specific afaik.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Guennadi Liakhovetski <lg@denx.de>
CC: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Added the struct containing PHY settings for the Vitesse VSC8211 phy to
the phy_info list in tsec.c
Signed-off-by: Pieter Henning <phenning@vastech.co.za>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The file was generated from building versatile_defconfig.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
