summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-04-12imx: ventana: config: set MMC env Partition to 1Tim Harvey
Partition 1 equates to EMMC boot0 Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-04-12mx6sabresd: README: Add eMMC boot configurationBreno Lima
Explain how to flash the eMMC and how to boot from it. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-12Set console speed to 115200 on mx6cuboxi.Vagrant Cascadian
By default, u-boot itself outputs on the serial console at 115200, so it may as well pass the same value to the booted operating system as well. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-12board: advantech: dms-ba16: apply the proper register setting to fix the ↵Yung-Ching LIN
voltage peak issue Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register to avoid the voltage peak issue while we do the IEEE PHY comformance test Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: fix AR8033 reset timing issueYung-Ching LIN
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: add the PMIC configuration supportYung-Ching LIN
Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: Add the configuration options for display ↵Yung-Ching LIN
initialization Add the configuration options for display initialization in case we need to do the display initialization in kernel to support different timing settings Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12MAINTAINERS: Fix ARM FREESCALE IMX filesJagan Teki
- Remove arch/arm/cpu/arm926ejs/imx/ which is not available - arch/arm/cpu/imx-common/ => arch/arm/imx-common/ Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-04-12MCCMON6: defconfig: Add tftp_nor_dtb command for NOR DTB updateLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-04-05ARM: mx5: Rename M53EVKMarek Vasut
The board is now manufactured by Aries Embedded GmbH , rename it. Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05ARM: mxs: Rename M28EVKMarek Vasut
The board is now manufactured by Aries Embedded GmbH , rename it. Signed-off-by: Marek Vasut <marex@denx.de>
2017-03-26configs: imx6: Select missing BOARD_LATE_INITJagan Teki
Select missing BOARD_LATE_INIT from configs/ to respective targets on arch area for Engicam imx6 boards. Cc: Tom Rini <trini@konsulko.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-26imx: ventana: add new board configs to MAINTAINERSTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-26imx: ventana: fix GW5903 VDD_ARM railTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20imx: ventana: config: add EMMC boot optionsTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20imx: ventana: add GW5903 supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20imx: ventana: add GW560x supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20imx: ventana: add GW5904 supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20drivers: net: phy: add MV88E6xx options to KconfigTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-20imx: mx6slevk: enable more DM driversPeng Fan
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO enabled. So needs to enable them together. DM FEC and SPI are not enabled, but they use gpio in board code. So use gpio_request first to request the gpio, because DM_GPIO is enabled. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-20imx: mx6slevk: introduce device tree supportPeng Fan
Introduce device tree support. dts from kernel commit c4f3f22edd Merge tag 'linux-kselftest-4.11-rc1' Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-20imx: mx6slevk: use SPI_BOOTPeng Fan
Use SPI_BOOT instead of SYS_BOOT_SPINOR. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-19ti: boot: Register the MMC controllers in SPL in the same way as in u-bootJean-Jacques Hiblot
To keep a consistent MMC device mapping in SPL and in u-boot, let's register the MMC controllers the same way in u-boot and in the SPL. In terms of boot time, it doesn't hurt to register more controllers than needed because the MMC device is initialized only prior being accessed for the first time. Having the same device mapping in SPL and u-boot allows us to use the environment in SPL whatever the MMC boot device. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-19Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/bk4r1_defconfig configs/colibri_vf_defconfig configs/pcm052_defconfig include/configs/colibri_vf.h include/configs/pcm052.h
2017-03-19Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich
Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-19imx: ventana: add EMMC configurationTim Harvey
Prepare for boards with EMMC instead of NAND flash Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-19tools: imximage: add set bit commandPeng Fan
Add set bit command support. Usage: SET_BIT 4 [address] [bitmask] Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19ARM: vf610: move to standard arch/board approachStefan Agner
Move Freescale/NXP Vybrid to a standard arch/board approach, similar to what has been done to i.MX 6 earlier in commit 89ebc82137be ("ARM: mx6: move to a standard arch/board approach"). Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19imx: ventana: make SD3_VSELECT board specificTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: make OTG VBUS power enable board specificTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: fix hwconfigTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: change name of rs232_en to indicate polarityTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: use mmc_root in boot scriptsTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: move mmc_init to commonTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: config: add gzwrite supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19imx: ventana: add additional DRAM configurationsTim Harvey
- 64bit 8gB density (4GiB) IMX6DQ - 64bit 4gB density (2GiB) IMX6SDL Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19colibri_imx7: split and resize firmware MTD partitionStefan Agner
Use two separate partitions for the two firmware instances. Also resize them to be of the same size which also makes the start of the UBI partition nicely aligned to 0x400000. In order to detect the new MTD layout and whether we run a U-Boot with the new BCB format or not, introduce a variable called "updlevel" which we can use in update/upgrade scripts. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2017-03-19colibri_imx7: use device-tree for MTD partitionsStefan Agner
Use device-tree fixup to communicate the MTD partitions to the kernel. Remove mtdparts from the kernel command line. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19colibri_imx7: setup PMIC sleep mode configurationStefan Agner
Disable 3.3V Ethernet and ARM rail when entering sleep mode. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19colibri_imx7: implement board level USB PHY modeStefan Agner
Implement board level USB PHY mode callback. On USB OTG Port 1 the Colibri standard foresees GPIO USBC_DET to decide whether the port should run in Host or Device mode. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19colibri_imx7/colibri_imx6/apalis_imx6: limit bootm memoryStefan Agner
Limit memory used for relocation of FDT or initrd. This is required to make sure that relocated artifacts are within lowmem. If fdt_high or initrd_high are not set, U-Boot automatically relocates artifacts to the end of memory. But this area won't be part of lowmem and hence will not be accessible by the kernel during early boot. With VM split set to 2G/2G (i.MX default), only the 2GB Apalis iMX6 is affected by that issue. With VM split set to 3G/1G (ARM default) also modules with 1GB of memory are affected. With the latter the amount of lowmem will be 760MiB. The value must also not exceed available memory! Use a safe value of 512MiB for Apalis and 256MiB for Colibri. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2017-03-19toradex apalis/colibri: add device tree overlay supportStefan Agner
Device tree overlays might prove useful in the future, enable it by default on all Toradex modules. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2017-03-19toradex apalis/colibri: use common USB product id fallbackStefan Agner
All modules use the common g_dnl_bind_fixup implementaton which calculates the PID according to product id (read from the config block) plus offset of 0x4000. In case there is no config block support (e.g. SPL) or in case the config block is not readable, fall back to a generic product id (product id 0, which can be interpreted as "Unknown Module"). Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2017-03-19mx7: Add 1.2GHz speed grade entryFabio Estevam
There are recent MX7 parts that have a 1.2GHz speed grade. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19mx7: Fix the get_cpu_speed_grade_hz() return valuesFabio Estevam
According to the MX7D fuse map the following speed grades are available: 800 MHz 500 MHz 1000 MHz 1200 MHz So simply return the real frequency that corresponds to the speed grade. With this change we see on boot: CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz) Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19mx7: Fix speed grade entryFabio Estevam
According to the MX7D fuse map the speed grade of the parts, which return '1' is 500MHz instead of 850MHz, so fix it accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19arm: dts: imx6ul: add usbotg aliasesSébastien Szymanski
This is needed to make the UMS command work again as it fails with the following error: BIOS> ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000 g_dnl_register: failed!, error: -19 ERROR: g_dnl_register failed at cmd/usb_mass_storage.c:179/do_usb_mass_storage() That's because usb_setup_ehci_gadget() function is looking for the usb device using the req_sed number. This change makes the usb device have a req_seq number and the UMS command work again: BIOS> ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000 CTRL+C - Operation aborted Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-03-19arm: i.MX6UL: add Armadeus Systems OPOS6UL SoM and OPOS6ULDev carrier boardSébastien Szymanski
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet phy. OPOS6ULDev is carrier board for the OPOS6UL. U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09) Trying to boot from MMC1 U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100) CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 40C Reset cause: POR Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board DRAM: 256 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Video: 800x480x18 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-19dm: imx: serial: add i.MX6UL supportSébastien Szymanski
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2017-03-19MCCMON6: defconfig: Move 'quiet' console parameter to 'console' env variableLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2025-01-19 12:47:19 +0000