summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-10-25tegra: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25serial: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25sdhci: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25omap_gpmc: fix warnigs with W=1Jeroen Hofstee
- make omap_spl_dev_ready static - make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25omap3: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25net: fec_mxc: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25lmb: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25image-fit: make local function staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25gpio: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25eth: make eth_address_set staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25env_nand: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25ehci-hcd.c: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25disk/part.c: make local function staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25common: board_r: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25common: cmd_elf: make do_bootelf_exec staticJeroen Hofstee
do_bootelf_exec was a weak function without a prototype nor and strong version. Just make it static. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25video: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25usb: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25samsung: board: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25pci: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25net: phy: fix warnings with W=1Jeroen Hofstee
get_phy_id is marked weak but has no protype nor a strong version, just make it static. Use __weak for board_phy_config. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25misc: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25cti_flash.c: use __weak when requested for flash_(read|write){8,16,32,64}Jeroen Hofstee
For various reasons (design, errata) boards may need to implement their own versions of these accessors. So in the case of CONFIG_CFI_FLASH_USE_WEAK_ACCESSOR mark the functions as weak. In the normal case mark them as static to allow for better optimization. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> [trini: Reword commit message] Signed-off-by: Tom Rini <trini@ti.com>
2014-10-24common: board: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-24arm: board: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-10-24sunxi: Add CONFIG_OLD_SUNXI_KERNEL_COMPAT Kconfig optionHans de Goede
Add a Kconfig option which users can select when they want to boot older kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5 "p" value to 1 (divide by 2) as that is what those kernels are hardcoded too, in the future this may enable further workarounds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Tom Rini <trini@ti.com> -- Changes in v2: -s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT. -Move the code block setting P(1) for old kernels to where P gets cleared
2014-10-24sunxi: dram: Use clock_get_pll5p to calculate mbus, rather then hardcodingHans de Goede
This is a preparation patch for making the pll5 "p" divisor configurable through Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Add clock_get_pll5p() functionHans de Goede
This is a preparation patch for making the pll5 "p" divisor configurable through Kconfig. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Increase command line buffer size (CONFIG_SYS_CBSIZE)Ian Campbell
I was running into this limit with a not overly long PXE append line. Since the PXE code wants to print the resulting command line increase CONFIG_SYS_PBSIZE too. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-10-24ARM: sunxi: Add Ippo-q8h-v5 A23 tablet board defconfigChen-Yu Tsai
Ippo q8h is a series of A23 tablet boards. This defconfig is for v5 of these boards, though for u-boot purposes they are mostly the same. See: http://linux-sunxi.org/Ippo_q8h Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add support for using R_UART as consoleChen-Yu Tsai
The A23 only has UART0 muxed with MMC0. Some of the boards we encountered expose R_UART as a set of pads. Add support for R_UART so we can have a console while using mmc. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Allow specifying module in prcm apb0 init functionChen-Yu Tsai
The prcm apb0 controls multiple modules. Allow specifying which modules to enable clocks and de-assert resets so the function can be reused. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add support for R_PIO gpio banksHans de Goede
The A31, A23 and later SoCs have an extra pin controller, called CPUs_PIO or R_PIO, which handles pin banks L and beyond. Also add a clear description about SUNXI_GPIO_BANKS, stating it only counts the number of pin banks in the _main_ pin controller. Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: expanded commit message] [wens@csie.org: add pin bank M and expand comments] [wens@csie.org: add comment on SUNXI_GPIO_BANKS macro] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add basic A23 supportChen-Yu Tsai
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use sun6i code for initial clock, gpio, and uart setup. There is no SPL support for A23, as we do not have any documentation or sample code for DRAM initialization. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24mmc: sunxi: Add support for sun8i (A23)Chen-Yu Tsai
The Allwinner A23 SoC has reset controls like the A31 (sun6i). The FIFO address is also the same as sun6i. Re-use code added for sun6i. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add support for uart0 on port F (mmc0)Chen-Yu Tsai
Allwinner SoCs provide uart0 muxed with mmc0, which can then be used with a micro SD breakout board. On the A23, this is the only way to use uart0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add sun8i (A23) UART0 pin mux supportChen-Yu Tsai
UART0 pin muxes on the A23 have a different function value. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Fix reset command on sun6i/sun8iChen-Yu Tsai
The watchdog on sun6i/sun8i has a different layout. Add the new layout and fix up the setup functions so that reset works. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk> [ ijc -- removed sun5i workaround from sun6i/sun8i codepath as discussed ]
2014-10-24ARM: sunxi: Add sun6i/sun8i timer block register definitionChen-Yu Tsai
The RTC hardware has been moved out of the timer block on sun6i/sun8i. In addition, there are more watchdogs available. Also note that the timer block definition is not completely accurate for sun5i/sun7i. Various blocks are missing or have been moved out. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Move watchdog register definitions to separate fileChen-Yu Tsai
On later Allwinner SoCs, the watchdog hardware is by all means a separate hardware block, with its own address range and interrupt line. Move the register definitions to a separate file to facilitate supporting newer SoCs. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Fix build break when CONFIG_MMC is not definedChen-Yu Tsai
BOOT_TARGET_DEVICES includes MMC unconditionally. This breaks when CONFIG_CMD_MMC is not defined. Use a secondary macro to conditionally include it when CONFIG_MMC is enabled, as we do for CONFIG_AHCI. This is used when we want to use uart0 from port F, which conflicts with mmc0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Add CONFIG_MACH_TYPE defines to sun4i, sun5i and sun7iHans de Goede
Many people are still using old linux-sunxi-3.4 kernels on sunxi devices, adding the proper MACH_TYPE defines for this allows people to switch to upstream u-boot, so that we can stop maintaining the linux-sunxi u-boot fork. These machine-ids are all properly registered at: http://www.arm.linux.org.uk/developer/machines/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Kconfig: Unify sunxi Kconfig codeHans de Goede
Unify the sunxi Kconfig code, instead of having separate code blocks for each of sun4i - sun7i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Enable second sdcard slot found on some boardsHans de Goede
Enable the second sdcard slot found on some boards. Note that we do not set CONFIG_MMC_SUNXI_SLOT_EXTRA for the SPL, as having it there is not useful, Except for on the Mele-M3 where the second sdcard is an eMMC, from which the device can also boot, and there we want to have both in the SPL, so that a single u-boot binary can both from both. So for the M3 we do prefix the defconfig setting with the special "+S:" syntax so that it applies to the SPL too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Use PG3 - PG8 as io-pins for mmc1Hans de Goede
None of the known sunxi devices actually use mmc1 routed through PH, where as some devices do actually use mmc1 routed through PG, so change the routing of mmc1 to PG. If in the future we encounter devices with mmc1 routed through PH, we will need to change things to be a bit more flexible. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: When we've both mmc0 and mmc2, detect from which one we're bootingHans de Goede
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're booting, and make that one "mmc dev 0" so that a single u-boot binary can be used for both the onboard eMMC and for external sdcards. When we're booting from mmc2, we make it dev 0 because that is where the SPL will load the tertiary payload (the actual u-boot binary in our case) from, see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Turn MMC_SUNXI_SLOT_EXTRA into a proper Kconfig optionHans de Goede
Note we also drop the SPL check for initializing the 2nd mmc slot, the SPL check is not necessary with Kconfig, because only options explicitly marked as also being for the SPL get set during SPL builds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Add mmc card-detect functionalityHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sun6i: Add Colombus board defconfigChen-Yu Tsai
The Colombus board is an A31 evaluation board from WITS Technology. Maxime has kindly agreed to maintain this board. [1] http://lists.denx.de/pipermail/u-boot/2014-September/190043.html Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi: Add basic A31 supportMaxime Ripard
Add a new sun6i machine that supports UART and MMC. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef around mmc and smp code, drop MACH_TYPE] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sun6i: Setup the A31 UART0 muxingMaxime Ripard
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: commit message was "ARM: sunxi: Setup the A31 UART0 muxing"] [wens@csie.org: reorder #ifs by SUN?I] [wens@csie.org: replace magic numbers with GPIO definitions] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
generated by cgit (git 2.34.1) at 2025-01-06 11:58:21 +0000