summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-10-23dm: omap: gpio: Support driver modelSimon Glass
Add driver model support to this driver, while retaining support for the legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO as usual. Since gpio_is_valid() no longer exists, we can use the -EINVAL error returned from gpio_request(). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: omap: gpio: Put _get_gpio_value() logic into its own functionSimon Glass
Add a separate internal helper function to get a GPIO value, so that we will be able to call it with the driver model version and avoid code duplication. Also move gpio_get_bank() and check_gpio() down below the helper functions as these won't be needed with driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: dts: omap: Select correct console for beagleboneSimon Glass
Select serial0 as the console. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com>
2014-10-23dm: serial: Support CONFIG_CONS_INDEX if availableSimon Glass
Try to use this option to select the correct uart for the console. This mimics the behaviour of drivers/serial.c. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: ns16550: Correct the probe logic for platform dataSimon Glass
The probe logic sets up the pointer to the platform data in the device tree decode method. It should be done in the probe() method, and anyway the device tree decode method can't be used when CONFIG_OF_CONTROL is not enabled. Fix these two problems. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: ns16550: Use an address instead of a pointer for the uart baseSimon Glass
It is inconvenient to have to use casts when specifying platform data. Also it is not strictly correct, since we should use map_sysmem() to convert an address to a pointer. Adjust the platform data to use an address. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: serial: ns16550: Correct logic for checking for characterSimon Glass
There is a bug in the logic which checks for an available character. This can cause invalid characters to be received - this was noticed on beaglebone. Fix it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: serial: Reset the watchdog while waiting in getc()Simon Glass
We have moved the busy-wait loop out of drivers and into the uclass. This means that we must reset the watchdog when busy-waiting. Note: some drivers may still have a busy-wait even with driver model, as a transition mechanism. Driver model will tolerate this, and is can be cleaned up when all users of the driver use driver model. An example is ns16550. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23dm: gpio: Support numbered GPIOsSimon Glass
At present banks must be named and it is not possible to refer to GPIOs by number in driver model. Some boards use numbering - e.g. OMAP. It is fairly easy to support by detecting the absense of a bank name (which starts with a letter). Add support for numbered GPIOs in addition to the existing bank support. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2014-10-23kbuild: clear VENDOR variable to fix build error on tcshMasahiro Yamada
Since the environment "VENDOR" is set in tcsh, it must be cleared in our makefile. Otherwise, boards without CONFIG_SYS_VENDOR fail to build: > make CROSS_COMPILE=arm-linux-gnueabi- wandboard_quad_defconfig all [ snip ] AR arch/arm/lib/lib.a CC arch/arm/lib/eabi_compat.o scripts/Makefile.build:55: /home/foo/u-boot/board/unknown/wandboard/ \ Makefile: No such file or directory make[2]: *** No rule to make target `/home/foo/u-boot/board/unknown/ \ wandboard/Makefile'. Stop. make[1]: *** [board/unknown/wandboard] Error 2 make: *** [__build_one_by_one] Error 2 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Tom Everett <tom@khubla.com> Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-23musb: fix warning in include/linux/usb/musb.hIgor Grinberg
Fix the following build warning by including linux/compat.h: include/linux/usb/musb.h:110: warning: 'struct device' declared inside parameter list include/linux/usb/musb.h:110: warning: its scope is only this definition or declaration, which is probably not what you want Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-23Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2014-10-23mips: enable CONFIG_USE_PRIVATE_LIBGCC by defaultMasahiro Yamada
Without the private libgcc, we need a full multilib toolchain with different libgcc or multiple toolchains to build all BE/LE and hard-float/soft-float variants of MIPS boards. That is not feasible. This commit allows us to build all the MIPS boards with a single kernel.org toolchain: https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/ x86_64-gcc-4.9.0-nolibc_mips-linux.tar.xz This change sounds reasonable for most users. If necessary, you can disable this option via "make menuconfig" or friends. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-10-23kconfig: invoke silentoldconfig if spl, tpl/.config is updatedMasahiro Yamada
When spl/.config is updated by "make spl/menuconfig" or friends, spl/include/config/auto.conf, spl/include/generated/autoconf.h and some other files must be updated by "make silentoldconfig". There is no hook for SPL in the top Makefile, so this commit touches .config when spl/.config is updated to invoke silentoldconfig. Likewise for TPL. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-23kbuild: fix a bug of the u-boot-spl link ruleMasahiro Yamada
cmd_u-boot-spl includes $(PLATFORM_LIBS) which changes when CONFIG_USE_PRIVATE_GCC is updated. The u-boot-spl image should be re-linked if any prerequisite is newer than it or the command line has changed. $(call, if_changed,...) should be used instead of $(call cmd,...). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-23kconfig: move CONFIG_USE_PRIVATE_LIBGCC to KconfigMasahiro Yamada
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86. Those architectures should "select" HAVE_PRIVATE_LIBGCC and CONFIG_USE_PRIVATE_LIBGCC should depend on it. Currently, this option is enabled on Tegra boards and x86 architecture. Move the definition from header files to Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
2014-10-23kbuild: drop CONFIG_USE_PRIVATE_LIBGCC=path/to/libgcc syntaxMasahiro Yamada
Now CONFIG_USE_PRIVATE_LIBGCC is only used as a boolean macro. Remove CONFIG_USE_PRIVATE_LIBGCC=path/to/libgcc syntax. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23x86: set CONFIG_USE_PRIVATE_LIBGCC to yMasahiro Yamada
The motivation of this commit is to change CONFIG_USE_PRIVATE_LIBGCC to a boolean macro so we can move it to Kconfig. In the current implementation, there are two forms of syntax for this macro: - CONFIG_USE_PRIVATE_LIBGCC=y - CONFIG_USE_PRIVATE_LIBGCC=path/to/private/libgcc The latter is only used by x86 architecture. With a little bit refactoring, it can be converted to the former. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23kconfig: move CONFIG_SYS_HZ to lib/KconfigMasahiro Yamada
CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h (but some boards still have redundant definitions). This commit moves the definition and the document in README to Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000, the sanity check in lib/time.c should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-10-23omap3/am33xx: mux: fix several checkpatch issuesIgor Grinberg
Fix the following checkpatch issues: CHECK: No space is necessary after a cast \#39: FILE: arch/arm/include/asm/arch-am33xx/mux.h:39: +#define PAD_CTRL_BASE 0x800 +#define OFFSET(x) (unsigned int) (&((struct pad_signals *) \ CHECK: Avoid CamelCase: <CONTROL_PADCONF_JTAG_nTRST> \#284: FILE: arch/arm/include/asm/arch-omap3/mux.h:284: +#define CONTROL_PADCONF_JTAG_nTRST 0x0A1C ERROR: space required after that ',' (ctx:VxV) \#446: FILE: arch/arm/include/asm/arch-omap3/mux.h:446: +#define MUX_VAL(OFFSET,VALUE)\ ^ Cc: Raphael Assenat <raph@8d.com> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Nishanth Menon <nm@ti.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefan Roese <sr@denx.de>
2014-10-23omap3: cm-t35: remove enable_gpmc_cs_config()Igor Grinberg
The gpmc_init() function already calls enable_gpmc_cs_config() for chip select 0. Although the bus width is configured for 16 bit, it gets reconfigured correctly in the omap_gpmc driver later. Remove the enable_gpmc_cs_config() function call and the associated gpmc_nand_config[] array. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-23omap3: cm-t35: use define for mmc wp gpioIgor Grinberg
Switch to using define for MMC WP GPIO instead of a magic number. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-23omap3: Kconfig: fix the cm-t35 board option promptIgor Grinberg
The cm-t35 board support covers both cm-t3530 and cm-t3730 boards. Mention both boards in the Kconfig option prompt. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-10-23am335x_evm: Correct "raw" portions of DFU alt intoTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-10-23am335x_boneblack: Only modify NAND/NOR/MMC1 pinmux on BBB in boneblack builds.Tom Rini
In the case of Beaglebone Black we only want to set the NAND or NOR cape pinmux when the config has been specifically modified by the user for this non-default case. Make the default be to set the MMC1 (eMMC) pinmux. We don't need similar changes for Beaglebone White as there is nothing on MMC1 by default there. Signed-off-by: Tom Rini <trini@ti.com>
2014-10-23arm: am43xx: switch over to CONFIG_ENV_IS_IN_FATFelipe Balbi
By using CONFIG_ENV_IS_IN_FAT it's far easier to have a private, minimal environment for e.g. booting off of network or mounting rootfs on NFS without having to modify the configuration header. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-23common: Makefile: allow for spl builds with env_fatFelipe Balbi
If CONFIG_SPL_BUILD and CONFIG_ENV_IS_IN_FAT are defined, u-boot spl will fail to build. Fix that. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-23omap3: overo: Add usb host supportStefan Herbrechtsmeier
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23omap3: overo: Separate module and expansion board MUX configurationStefan Herbrechtsmeier
Separate overo module and expansion board MUX configuration. This allows an foreign expansion board to use the boot loader without any adaption. It only needs to save the expansion name in the EEPROM to load a specific device tree. Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23omap3: overo: Move ethernet setup to board_eth_init functionStefan Herbrechtsmeier
Move ethernet setup to the board_eth_init function and select the available network devices via expansion id. Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23omap3: overo: Call bootm only after successful nand readStefan Herbrechtsmeier
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
2014-10-23ARM: keystone: cmd_ddr3: add ddr3 commands to test ddrHao Zhang
Add ddr3 commands: test <start_addr in hex> <end_addr in hex> - test DDR from start\n address to end address\n ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n compare DDR data of (size) bytes from start address to end address\n ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n in DDR data at <addr>, the command will read a 32-bit data\n from <addr>, and write (data ^ bit_err) back to <addr>\n Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used for ddr3 commands and for now it's not needed any more. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23keystone2: ecc: add ddr3 error detection and correction supportVitaly Andrianov
This patch adds the DDR3 ECC support to enable ECC in the DDR3 EMIF controller for Keystone II devices. By default, ECC will only be enabled if RMW is supported in the DDR EMIF controller. The entire DDR memory will be scrubbed to zero using an EDMA channel after ECC is enabled and before u-boot is re-located to DDR memory. An ecc_test environment variable is added for ECC testing. If ecc_test is set to 0, a detection of 2-bit error will reset the device, if ecc_test is set to 1, 2-bit error detection will not reset the device, user can still boot the kernel to check the ECC error handling in kernel. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone: msmc: extend functionality of SESVitaly Andrianov
Add functions to set/get SES PMAX values of Pivilege ID pair. Also add msmc module definitions. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23dma: ti-edma3: introduce edma3 driverKhoronzhuk, Ivan
The EDMA3 controller’s primary purpose is to service data transfers that you program between two memory-mapped slave endpoints on the device. Typical usage includes, but is not limited to the following: - Servicing software-driven paging transfers (e.g., transfers from external memory, such as SDRAM to internal device memory, such as DSP L2 SRAM) - Servicing event-driven peripherals, such as a serial port - Performing sorting or sub-frame extraction of various data structures - Offloading data transfers from the main device DSP(s) - See the device-specific data manual for specific peripherals that are accessible via the EDMA3 controller Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23board: k2e_evm: add network supportHao Zhang
This patch adds network support code and enables keystone_net driver usage for k2e_evm evaluation board. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone: clock: add support for K2E SoCsKhoronzhuk, Ivan
For K2E and K2L SoCs clock output from PASS PLL has to be enabled after NETCP domain and PA module are enabled. So create new function for that and call it after PA module is enabled. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: increase PHY auto negotiate timeKhoronzhuk, Ivan
The new Marvel PHY (88E1514) used on K2L/K2E EVM requires longer time to auto negotiate with SoC's SGMII port. It can take about 3 sec to up the PHY after reset, so add code to expose sgmii auto negotiation waiting process. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: add Keystone2 K2E SoC supportKhoronzhuk, Ivan
The Keystone2 Edison SoC uses the same keystone net driver. This patch adds opportunity to use it by K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_serdes: add keystone K2E SoC supportKhoronzhuk, Ivan
Keystone2 Edison SoC uses the same keystone SerDes driver. This patch adds support for K2E SoCs. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23ARM: keystone2: keysonte_nav: add support for K2E SoCKhoronzhuk, Ivan
Keystone2 Edison SoC uses the same keystone navigator, but uses different NETCP PktDMA definitions. This patch adds required definitions. Acked-by: Vitaly Andrianov <vitalya@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: use general get link functionKhoronzhuk, Ivan
The phy framework has function to get link, so use it instead of own implementation. There is no reason to check SGMII link while sending each packet, phy link is enough. Check SGMII link only while ethernet open. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: register eth PHYs on MDIO busKhoronzhuk, Ivan
As MDIO bus has been added we can register PHYs with it. After registration, the PHY driver will be probed according to the hardware on board. Startup PHY at the ethernet open. Use phy_startup() instead of keystone_get_link_status() when eth open, as it verifies PHY link inside and SGMII link is checked before. For K2HK evm PHY configuration at init was absent, so don't enable phy config at init for k2hk evm. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: register MDIO busKhoronzhuk, Ivan
Currently MDIO framework is not used to configure Ethernet PHY. As result some of already implemented functions are duplicated. So register MDIO bus in order to use it. On that stage it's just registered, it'll be used as we start to use PHY framework. Use mdio bus read/write/reset functions in the driver. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: keystone_net: use mdio_reset functionKhoronzhuk, Ivan
Don't use mdio_enable twice while eth open. Also rename it to keystone2_mdio_reset as more appropriate name. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23net: phy: print a number of phy that is not foundKhoronzhuk, Ivan
In case when several Ethernet ports are supported it's convenient to see the number of phy that is not found. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: generalize configuration mechanismKhoronzhuk, Ivan
The cmu, comlane, lane configuration mechanism are similar for sub systems as well such as PCI or sRIO, but they have different values based on input clock and output bus rate. According to this compact driver to simplify adding different configuration settings based on clock and rate. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: generalize to be used by other sub systemsHao Zhang
SerDes driver is used by other sub systems like PCI, sRIO etc. So modify it to be more general. The SerDes driver provides common API's that can also be extended for other peripherals SerDes configurations. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: enhance to use cmu/comlane/lane specific configurationsHao Zhang
Enhance the driver to use cmu/comlane/lane specific configurations instead of 1 big array of configuration. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23soc: keystone_serdes: create a separate SGMII SerDes driverKhoronzhuk, Ivan
This patch split the Keystone II SGMII SerDes related code from Ethernet driver and create a separate SGMII SerDes driver. The SerDes driver can be used by others keystone subsystems like PCI, sRIO, so move it to driver/soc/keystone directory. Add soc specific drivers directory like in the Linux kernel. It is going to be used by keysotone soc specific drivers. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
generated by cgit (git 2.34.1) at 2025-01-22 21:03:42 +0000