summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-10-02Blackfin: fix MMC init output alignmentMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: blackvme: new board portWojtek Skulski
The board includes: * ADSP-BF561 rev. 0.5 * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG) * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell) * SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB) * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB) * Spartan6-LX150 (memory-mapped; both PPIs also connected) * See http://www.skutek.com/ Signed-off-by: Wojtek Skulski <skulski@pas.rochester.edu> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: propagate target cpu defines when building embedded envMike Frysinger
Since we're no longer extracting the env from the target ELF file (since upstream wouldn't take that change), we're back to the problem of cpu defines not properly propagating to the env setup stage. So the embedded env built by the host compiler doesn't match the one that is linked into the u-boot env. Reported-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: cmd_gpio: accept upper case pin namesMike Frysinger
The intention all along was to accept pin names irrelevant of their case. But I guess I forgot to test/implement support for that. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf526-ezbrd: enable BootROM-OOB layout when booting from NANDMike Frysinger
We need to use the Blackfin BootROM-specific OOB layout when we boot out of NAND as that is what the on-chip ROM expects. Also need to increase the monitor size a little to accommodate the extra NAND code overhead. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: adi config: enable nand lock/unlock supportMike Frysinger
We use the lock/unlock options in our default nand code, so enabl support for the options. Reported-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bct-brettl2: new board portPeter Meerwald
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: adi config: allow boards to tweak a little moreMike Frysinger
Let people easily override bootdelay and network settings. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: cmd_gpio: return gpio value to callerMike Frysinger
Make the GPIO command usable in a scripting environment by returning the GPIO value rather than always 0. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf527-sdp: new board portMike Frysinger
Support for the Blackfin System Development Platform (SDP) base module. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: adi config: add a hook for boards to append the envMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: adi config: add an "all spi flashes" option to unify board listsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: support a 3rd gpio cfi pinPeter Meerwald
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: cmd_gpio: document/extend input sub-optionMike Frysinger
The input sub command was missing from the help text, and it didn't show the actual value currently read on the GPIO. This allows people to read the value of input pins. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: move CONFIG_BFIN_CPU to board config.mkMike Frysinger
The CONFIG_BFIN_CPU option is largely used in the build system, so move it out of the board config.h and into the board config.mk. It'd be nice to keep everything in the config.h, but the patch to extract that value early was rejected. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf561: merge headersMike Frysinger
Only the BF561 port was using the common dual core headers, so merge them into the BF561 specific headers. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf533: merge headersMike Frysinger
Only the BF533 port was using the common extended headers, so merge them into the BF533 specific headers. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: unify core MMRsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf52x: unify arch header duplicationMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf537: unify arch header duplicationMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: punt old *p style volatile MMR definesMike Frysinger
These are unused now, so punt them to clean things up. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf527-ad7160-eval: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: cm-bf548: video: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf548-ezkit: video: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf527-ezkit: video: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bf537-stamp: post: update old MMR style macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. For the GPIO MMR usage, convert to the new GPIO framework. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bfin_mac: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: punt headers for non-existent BF541Mike Frysinger
There is no BF541 processor variant, so punt headers for it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: unify gpio cfi implementationsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bfin_sdh: clean up send_cmdMike Frysinger
Simplify the command setup and status checking steps, and add a proper timeout to the status polling code to avoid possible infinite hangs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bfin_spi: add optional DMA supportMike Frysinger
This moves the last piece from the old spi_flash driver to the new SPI framework -- optional DMA RX support. This typically cuts speeds by ~40% at the cost of additional ~300 bytes. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: add support for BF51x partsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: add support for BF538/BF539 processorsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-30MX51: Register definitions cannot be included in board config fileStefano Babic
Due to wrong dependencies, it is not possible to include imx_regs.h inside the board configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-30MXC: Fix byte-ordering in SPI driver for i.MX31/i.MX51Stefano Babic
The actual SPI driver for i.MX31 and i.MX51 controller use a wrong byte ordering, because it is supposed to work only with Freescale's devices, as the Power Controllers (PMIC). The driver is not suitable for general purposes, because the buffers passed to spi_xfer must be 32-bit aligned, as it is used mainly to send integer to PMIC devices. The patch drops any kind of limitation and makes the driver useful with devices controlled sending commands composed by single bytes (or by a odd number of bytes), such as spi flash, sensor, etc. Because the byte ordering is changed, any current driver using this controller must be adapted, too. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-30MXC: Correct SPI_CPOL setting in SPI driverStefano Babic
The handling of the SPI_CPOL bit inside the SPI driver was wrong. As reported by the manual, the meaning of the SSPOL inside the configuration register is the same as reported by SPI specification (0 if low in idle, 1 is high on idle). The driver inverts this logic. Because this patch sets the logic as specified, it is required to clear the CPOL bit in the configuration file to adapt to the correct logic. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: David Jander <david.jander@protonic.nl>
2010-09-29MX51: Drop unused header file for mx51evkStefano Babic
As stated in 272017853339f5b9685f9488bdaf5405812d12a4, the mx51evk has not CPLD and all references must be removed. This patch drop a .h file that still remains in board directory. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29MXC: Add watchdog support to serial driverStefano Babic
Calls WATCHDOG_RESET() inside serial driver for boards enabling watchdog. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29MX51: add structure to access System Reset ControllerStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29MX51: Added pins definition to set up padsStefano Babic
Add pins definitions to set up RAM pads. Pins have only a pad, there is no entry in the multiplexer. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29ARM: Use syslib functions for all CORTEXA8Stefano Babic
The OMAP3 cpu directory contains a syslib file with some utilities that can be shared by all targets using arm cortexa8 processors, not only OMAP. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29Use common function to set GPIOs for MX3 and MX5Stefano Babic
The patch adds support for setting gpios to the MX51 processor and change name to the corresponding functions for MX31. In this way, it is possible to get rid of nasty #ifdef switches related to the processor type. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-28Merge branch 'next' of /home/wd/git/u-boot/nextWolfgang Denk
Conflicts: include/ppc4xx.h Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28Prepare v2010.09Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28mpc512x: fix build issuesWolfgang Denk
Commit 800eb0964 "POST cleanup." removed file arch/powerpc/cpu/mpc512x/common.c but failed to remove the reference to it from arch/powerpc/cpu/mpc512x/Makefile which causes somewhat obscure build errors: make[1]: *** No rule to make target `/work/wd/tmp-ppc/arch/powerpc/cpu/mpc512x/.depend', needed by `_depend'. Stop. Fix these. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28ARMV7: OMAP3: Update Beagle xM pinmux with USB hub and DVI gpio setupSteve Sakoman
This patch adds missing pinmux setup for 4 GPIO signals used on the Beagle xM: - USB hub reset (gpio_56) - P8 USB hub reset (gpio_63) - DVI enable (gpio_129) - P8 DVI enable (gpio_170) Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-28ARMV7: OMAP4: Calculate SDRAM sizeAneesh V
Calculate the SDRAM size from DMM configuration registers instead of using hard-coded values. This gives correct values for all different boards. It's assumed that DMM sections do not overlap memory areas. Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-28ARMV7: OMAP4: Fix Panda pinmux setting to enable Wifi/BT ModuleSteve Sakoman
This patch corrects the pinmux settings to enable proper functioning of the wifi/bluetooth module. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-28ixp/npe: Remove duplicated commentThomas Weber
Signed-off-by: Thomas Weber <weber@corscience.de>
2010-09-28bmw: Remove duplicated include of header fileThomas Weber
Signed-off-by: Thomas Weber <weber@corscience.de>
generated by cgit (git 2.34.1) at 2024-12-28 05:54:11 +0000