| Age | Commit message (Collapse) | Author |
|---|
|
This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.
Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
re-configuration
B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes,
add their defines in arch/powerpc/include/asm/config_mpc85xx.h
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.
Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.
The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
common header file for all platforms, containing defines and declarations used
by GPMC NAND driver.
(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
SoC platform specific header file containing defines like ECC layout.
This patch removes platform specific arch-xx/omap_gpmc.c because:
- GPMC hardware engine is common for all SoC platforms hence only (a) is enough
- ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
selected. Hence all ECC layout declarations in (b) are redundant.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
|
|
README.malta referred to board/malta, but malta has now been moved
within board/imgtec/, so correct the path.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
|
|
Linux MIPS uses asm-generic/int-ll64.h in asm/types.h.
Thus u64 and __u64 are defined as unsigned long long. Port this
over to U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
There are no source files in board/synopsys/arcangel4/
directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
|
|
U-Boot has compelled all boards to have
board/${BOARD}/ or board/${VENDOR}/${BOARD}/ directory.
Sometimes it does not seem suitable for some boards,
for example Sandbox. (Is it a board?)
And arcangel4 board has nothing to compile
under the board directory.
This commit makes the build system more flexible:
If '<none>' is given to the 6th column (=Board name) of boards.cfg,
Kbuild will not descend into the board directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
LOGO_BMP was never overwritten by board-specific or
vendor-specific logos.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
|
|
Programs in tools/ directory are usually built for the host.
But some of them (mkimage, dumpimge, gen_eth_addr, etc.) are
useful on the target OS too.
Actually, prior to Kbuild, U-Boot could build tools for
the target like follows:
$ make <target_board>_config
$ export CROSS_COMPILE=<cross_gcc_prefix>
$ make HOSTCC=${CROSS_COMPILE}gcc HOSTSTRIP=${CROSS_COMPILE}strip tools
In Kbuild, we can no longer replace HOSTCC at the command line.
In order to get back that feature, this commit adds "cross-tools" target.
Usage:
Build tools for the host
$ make CROSS_COMPILE=<cross_gcc_prefix> tools
Build tools for the target
$ make CROSS_COMPILE=<cross_gcc_prefix> cross_tools
Besides, "make cross_tools" strip tools programs because we
generally expect smaller storages on embedded systems.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
The top Makefile must export HOST_TOOLS_ALL to use it
in tools/Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
config.tmp is not there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Ignore
- board/cray/L1/bootscript.{c|image}
- board/matrix_vision/mvblm7/bootscript.img
- board/maxtir_vision/mvsmr/bootscript.img
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
|
|
The same outputs are generated with or without -I$(TOPDIR)/board.
I cannot understand why it is necessary. Remove.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
|
|
The syntax
CROSS_COMIPLE ?= <cross_compiler_prefix>
does not work because config.mk is parsed after
exporting CROSS_COMPILE.
Like Linux Kernel's arch/$(ARCH)/Makefile,
we must write as follows:
ifeq ($(CROSS_COMPILE),)
CROSS_COMPILE := <cross_compiler_prefix>
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We had switched to Kbuild so now we can specify
PLATFORM_LIBS/PLATFORM_LIBGCC with relative path.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Update to v3.14-rc4's version of checkpatch.pl. In doing so we drop the
changes to top_of_kernel_tree() as we pass in --no-tree and drop our
changes about MAINTAINERS as that's for reporting checkpatch.pl problems
itself (and upstream has said they'll reword this section to be
clearer).
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add 64-bit data for memory commands, such as md, mw, mm, cmp. The new
size ".q " is introduced.
For 64-bit architecture, 64-bit data is enabled by default, by detecting
compiler __LP64__. It is optional for other architectures.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This documentation pertains to the planned implementation of driver model
in U-Boot for each subsystem, but it has not been superseded. It is
probably better to have this documentation in the source code for each
subsystem where possible, so that docbook will pick it up. Where this does
not make sense, new documentation can be placed in some suitable file in
doc/driver-model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that named GPIO banks are supported, along with a way of obtaining
the status of a GPIO (input or output), we can provide an enhanced
GPIO command for driver model. Where the driver provides its own operation
for obtaining the GPIO state, this is used, otherwise a generic version
is sufficient.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert sandbox over to use driver model GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.
Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.
The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.
Anonymous GPIO banks are also supported, and are just numbered without any
prefix.
Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
|
|
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.
To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.
The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
|
|
This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
|
|
Add some tests of driver model functionality. Coverage includes:
- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed
This function is enabled for sandbox, using CONFIG_DM_TEST.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Make driver model available after relocation, by setting up data structures
and scanning for devices using compiled-in platform_data and (when available)
the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use driver model in sandbox to permit running of driver model unit test.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add driver model functionality for generic board.
This includes data structures and base code for registering devices and
uclasses (groups of devices with the same purpose, e.g. all I2C ports will
be in the same uclass).
The feature is enabled with CONFIG_DM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
|
|
This adds a README to help with understanding of this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
U-Boot already has a list implementation, and files which include both
that and the yaffs implementation will get errors:
In file included from ydirectenv.h:80:0,
from yportenv.h:81,
from yaffs_guts.h:19,
from yaffs_allocator.h:19,
from yaffs_allocator.c:14:
yaffs_list.h:32:8: error: redefinition of ‘struct list_head’
struct list_head {
^
Remove the yaffs implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
U-Boot now uses errors defined in include/errno.h which are negative
integers. Commands which fail need to report the error and return 1
to indicate failure. Add this functionality in cmd_process_error().
For now this merely reports the error number. It would be possible
also to produce a helpful error message by storing the error strings
in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE
option to make it easier to use device tree with sandbox.
This adjusts the Makefile to build a u-boot.dtb file which can be passed
to sandbox U-Boot with:
./u-boot -d u-boot.dtb
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Now we have two different frameworks for doing the same thing.
I'd like to propose to drop nand_spl framework.
How about deleting it before v2014.07 release?
In the interim, this commit will display a warning message
when compiling nand_spl board.
Now we have 19 nand_spl boards:
MPC8315ERDB_NAND
SIMPC8313_LP
SIMPC8313_SP
MPC8536DS_NAND
MPC8569MDS_NAND
MPC8572DS_NAND
P1023RDS_NAND
P1011RDB_NAND
P1020RDB_NAND
P2010RDB_NAND
P2020RDB_NAND
acadia_nand
bamboo_nand
canyonlands_nand
glacier_nand
haleakala_nand
kilauea_nand
rainier_nand
sequoia_nand
They must be ported to SPL before the deadline,
otherwise they will be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
All arch/m68k/cpu/*/config.mk define the same flags
PLAGFORM_REFLFLAGS += -ffixed-d7 -msep-data
Move it to arch/m68k/config.mk
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
|
|
-ffixed-r13 is defined commonly for sh2, sh3, sh4.
Move it to arch/sh/config.mk
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
-ffreestanding is defined at the top Makefile for all architectures.
Do not define it twice for SH2A.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
-Wstrict-prototypes, -ffreestanding, -fno-stack-protector
are defined at the top Makefile for all architectures.
Do not define them twice for x86.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
board/sheldon/simpc8313/config.mk is used only for nand_spl.
So it should go into nand_spl/board/sheldon/simpc8313/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
