summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-03-14tegra: usb: make controller init functions more self containedLucas Stach
There is no need to pass around all those parameters. The init functions are able to easily extract all the needed setup info on their own. This allows to move out the controller init into ehci_hcd_init later on, without having to save away global state for later use and thus bloating the file global state. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14tegra: usb: set USB_PORTS_MAX to correct valueLucas Stach
Both Tegra20 and Tegra30 have a max of 3 USB controllers. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-13ARM: tegra: enable some CPU errata workaroundsStephen Warren
Tegra20 has a Cortex A9 r1p1, and Tegra30 has a Cortex A9 r2p9. As such, some CPU errata exist, and must be worked around. These must be worked around in the bootloader, since in general, the kernel (especially a multi-platform kernel) needs to support being launched in non-secure mode (normal world), and hence may not be able to write to the CP15 register to enable these workarounds. Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-03-13ARM: implement some Cortex-A9 errata workaroundsStephen Warren
Various errata exist in the Cortex-A9 CPU, and may be worked around by setting some bits in a CP15 diagnostic register. Add code to implement the workarounds, enabled by new CONFIG_ options. This code was taken from the Linux kernel, v3.8, arch/arm/mm/proc-v7.S, and modified to remove the logic to conditionally apply the WAR (since we know exactly which CPU we're running on given the U-Boot configuration), and use r0 instead of r10 for consistency with the rest of U-Boot's cpu_init_cp15(). Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2013-03-13Add Boundary Devices Nitrogen6X boardsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-03-12Refactor linker-generated arraysAlbert ARIBAUD
Refactor linker-generated array code so that symbols which were previously linker-generated are now compiler- generated. This causes relocation records of type R_ARM_ABS32 to become R_ARM_RELATIVE, which makes code which uses LGA able to run before relocation as well as after. Note: this affects more than ARM targets, as linker- lists span possibly all target architectures, notably PowerPC. Conflicts: arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds arch/arm/cpu/armv7/omap-common/u-boot-spl.lds board/ait/cam_enc_4xx/u-boot-spl.lds board/davinci/da8xxevm/u-boot-spl-da850evm.lds board/davinci/da8xxevm/u-boot-spl-hawk.lds board/vpac270/u-boot-spl.lds Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12arm: make __bss_start and __bss_end__ compiler-generatedAlbert ARIBAUD
Turn __bss_start and __bss_end__ from linker-generated to compiler-generated symbols, causing relocations for these symbols to change type, from R_ARM_ABS32 to R_ARM_RELATIVE. This should have no functional impact, as it affects references to __bss_start and __bss_end__ only before relocation, and no such references are done. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12Remove linker lists (LGAs) from SPL linker scriptsAlbert ARIBAUD
Many SPL linker scripts needlessly include linker lists (aka LGAs). Remove them whenever possible; keep it only in the seven am335x_evm variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot), where there is actual content in output section .u_boot_list. This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets byte-identical. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12arm: omap: map u_boot_lists section to .sramAlbert ARIBAUD
Output section .u_boot_list was left unmapped in u-boot-spl.lds for omap-common, causing the location counter to roll back to bteween .rodata and .data, making __image_copy_end and _end symbols wrong. Mapping output section .u_boot_list to memory .sram fixes these symbols' mapping. This modifies the SPL binary but has no functional impact, as __image_copy_end and _end are never used in SPLs and u_boot_list is empty for all 29 boards affected (omap4_sdp4430 eco5pk igep0030 am335x_evm_uart3 omap3_beagle am3517_crane igep0032 mt_ventoux pcm051 am3517_evm omap3_evm_quick_mmc am335x_evm_uart2 am335x_evm_spiboot am335x_evm_uart1 omap3_evm igep0030_nand omap3_overo igep0020 am335x_evm omap4_panda omap5_evm am335x_evm_uart4 devkit8000 tricorder mcx twister omap3_evm_quick_nand am335x_evm_uart5 igep0020_nand). Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12I2C: S3C24X0: Bug fixes in i2c_transferRajeshwari Shinde
This patch corrects the following issues 1) Write the correct M/T Stop value to I2CSTAT after i2c write. According to the spec, after finish the data transmission, we should write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA). 2) Not split the write to I2CSTAT into 2 steps in i2c read. According to the spec, we should write the combined M/R Start value to I2CSTAT after setting the slave address to I2CDS 3) Fix the mistake of making an equality check to an assignment. In the case of I2C write with the zero-length address, while tranfering the data, it should be an equality check (==) instead of an assignment (=). Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2013-03-12I2C: S3C24X0: Remove the dead codeRajeshwari Shinde
This revomes the code under #if 0 in the s3c24x0_i2c driver. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2013-03-12cmd_mem.c: Fix warning when CONFIG_CMD_MEMTEST is not setTom Rini
mem_test_quick and mem_test_alt functions are only called by do_mem_mtest, so move them under the #ifdef Signed-off-by: Tom Rini <trini@ti.com>
2013-03-12CONFIG_BOOTDELAY default should not affect runtimeJoe Hershberger
Because the code that handles bootdelay is compiled in conditionally based on the default value, you are restricted in the default, regardless of what you want the runtime options to be. Change the source to always check if any default is given so that other values can be selected and used at runtime. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-12common/main: move set_working_fdt_addr to enable usage of $fdtaddrBarak Wasserstrom
When using $fdtaddr in $bootcmd and $bootcmd is automatically called, $fdtaddr is yet not defined. Signed-off-by: Barak Wasserstrom <wbarak@gmail.com>
2013-03-12env: fix "env ask" commandWolfgang Denk
The "env ask" traditionally uses a somewhat awkward syntax: env ask name [message ...] [size] So far, when a mesage was given, you always also had to enter a size. If you forgot to do that, the command would terminate without any indication of the problem. To avoid incompatible changes of the interface, we now check the last argument if it can be converted into a decimal number. If this is the case, we assume it is a size; otherwise we treat it as part of the message. Also, add a space after the message fore easier reading, and clean up help mesage. Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-03-12cmd_fat.c: Note in fatread help about alignment requirementsTom Rini
When using the partial read feature of fatwrite the buffer we read into can become unaligned not just due to initial location but the size of our partial reads as well. Make this clear in the help text. Signed-off-by: Tom Rini <trini@ti.com>
2013-03-12Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-03-12ARM: sam9x5: fix ethernet pins in MII modeJesse Gilles
Fix pin setting in MII mode Signed-off-by: Jesse Gilles <jgilles@multitech.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12ARM: at91sam9x5: Using CPU string directlyBo Shen
As the CPU name is not configurable, using CPU string directly Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12ARM: at91: change nand flash tableBo Shen
Change nand flash partition table according to www.at91.com/linux4sam more information: http://www.at91.com/linux4sam/bin/view/Linux4SAM/GettingStarted#Linux4SAM_NandFlash_demo_Memory Signed-off-by: Bo Shen <voice.shen@atmel.com> [minor commit message changes] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12arm: at91/configs: add bootz to configurationNicolas Ferre
Support to boot zImage Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> [Add bootz for at91rm9200, at91sam9263, at91sam9rl] Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12arm: at91/configs: add libfdt to configurationNicolas Ferre
support to boot device tree Linux kernel Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> [Add libftd for at91rm9200, at91sam9263, at91sam9rl] Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-12mmc:sdhci:fix: Change default interrupts enabled at SDHCI initializationŁukasz Majewski
This patch changes sdhci_init()'s behavior to NOT enable all interrupt sources by default. Moreover interrupt signaling has been disabled. This patch do not enable interrupts which aren't served in u-boot (they are defined at sdhci.h but NOT used elsewhere): - SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER, SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT Special care shall be put on SDHCI_INT_CARD_INT, which indicates interrupt generated by SD card. According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8 (Card Interrupt Status Enable) at "Normal Interrupt Status Enable Register" (offset 0x34) is set, the card interrupt detection is started. Then eMMC card may cause the SD controller to set this bit and then this interrupt is passed to booted OS and might cause kernel crash. To sum up: - Only enable interrupts, which are served at u-boot - This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at Linux kernel (versions 3.6+, sdhci controller) - Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS5: Snow: Add a configuration fileRajeshwari Shinde
This patch adds the configuration file for Snow Board and defines the same in boards.cfg. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS5: Add initial DTS file for Snow.Rajeshwari Shinde
This patch adds the DTS file for Snow Board. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: FDT: Add a H/W-trip member to TMU nodeAkshay Saraswat
This adds a member to TMU FDT node for providing hardware tripping temperature threshold. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add hardware trippingAkshay Saraswat
This adds hardware tripping at 110 degrees celsius which must enable forced system shutdown in case TMU fails to power off. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: Config: Enable dtt command for TMUAkshay Saraswat
This enables the dtt command to read the current SOC temperature with the help of TMU Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12TMU: Add TMU support in dtt commandAkshay Saraswat
Add generic TMU support alongwith i2c sensors in dtt command to enable temperature reading in cases where TMU is present along-with/instead-of i2c sensors. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: Config: Enable support for Exynos TMU driverAkshay Saraswat
Enables TMU driver support for exynos5250 Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add TMU init and status checkAkshay Saraswat
This adds call to tmu_init() and TMU boot time analysis for the SoC temperature threshold breach. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: FDT: Add TMU device node valuesAkshay Saraswat
Fdt entry for Exynos TMU driver specific pre-defined values used for calibration of current temperature and defining threshold values. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12Exynos5: TMU: Add driver for Thermal Management UnitAkshay Saraswat
Adding Exynos Thermal Management Unit driver to monitor SOC temperature and take actions corresponding to states of TMU. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12SMDK5250: FDT: Retrieve board model via DTRajeshwari Shinde
Print out the board model by parsing the device tree file. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12EXYNOS: Correct ordering of SPL machine_paramsSimon Glass
The mem_manuf is not in the correct order according to the string table. This causes cros_bundle_firmware to get the BL2 settings in the wrong order. This patch fixes the same. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-11env: Allow accessing non-mtd devicesLubomir Rintel
In certain cases, memory device is present as flat file or block device (via mmc or mtdblock layer). Do not attempt MTD operations against it. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2013-03-11cmd_df.c: Delete this clearly unused source file.Robert P. J. Day
Nothing appears to use or compile cmd_df.c anymore. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11cmd_mtdparts.c: Correct "reseting" to "resetting" in error msgsRobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11Allow u-boot to be silent without forcing Linux to beJoe Hershberger
That's a bit presumptuous of you, u-boot! Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-11Fix a couple typoes in tools/env/READMERobert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-03-11tools: update checkpatch to latest upstream versionKim Phillips
i.e., from the linux kernel's commit be987d9f80354e2e919926349282facd74992f90 Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-03-11tools: enable more checkpatch tests by defaultKim Phillips
without this, patches don't get checked for proper alignment, and e.g., for spaces after a cast and/or before a semicolon. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-03-11cmd_part: don't print cmd name twice in helpStephen Warren
The core implementation of "help" already prints the command name before the help text of a specific command. Remove it from part's own help text to avoid it being printed twice: Tegra114 (Dalmore) # help part part - disk partition related commands Usage: part part uuid <interface> <dev>:<part> - print partition UUID ... Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-03-11MAKEALL: fix kill_children for BSD hostsAndreas Bießmann
ps on BSD hosts (like OS X) do not provide the --no-headers switch nor understand the AIX format descriptions. Unfortunately there seems no solution to get the PIDs of children in a platfrom independent manner. Therefore detect the OS and decide upon that which way to go. This patch makes the MAKEALL script cleanly stoppable on bare OS X when using the parallel builds of targets. Additionally this patch removes double call to grep by a single call to sed for GNU style child PID detection. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-03-11mvsata_ide.c: Correction of typo in commentsGray Remlin
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
2013-03-11ppc: Remove PCIPPC2 and PCIPPC6 boardsStefan Roese
These boards seem to be unmaintained for quite some time. So lets remove support for them completely. This also cleans up some common drivers/files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch> Acked-by: Wolfgang Denk <wd@denx.de>
2013-03-11display_options:print_buffer: align ASCII printAndreas Bießmann
This patch adds whitespace to the printed hex numbers to have an aligned ASCII printout at the end of the line. This changes for example the md output from: ---8<--- OMAP3 Tricorder # md.l $loadaddr 5 82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........ 82000010: 01010000 .... --->8--- to ---8<--- OMAP3 Tricorder # md.l $loadaddr 5 82000000: 30200109 20a4028c 90010000 08a00000 .. 0... ........ 82000010: 01010000 .... --->8--- The cost of this is about 72 byte .text increase (tested with at91 build). Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-03-11Feature Removal: disable "mtest" command by defaultWolfgang Denk
The "mtest" command is of little practical use (if any), and experience has shown that a large number of board configurations define useless or even dangerous start and end addresses. If not even the board maintainers are able to figure out which memory range can be reliably tested, how can we expect such from the end users? As this problem comes up repeatedly, we rather do not enable this command by default, so only people who know what they are doing will be confronted with it. As this changes the user interface, we allow for a grace period before this change takes effect. For now, we make "mtest" configurable through the CONFIG_CMD_MEMTEST variable, which is defined in include/config_cmd_default.h; we also add an entry to doc/feature-removal-schedule.txt which announces the removal of this default setting in two releases from now, i. e. with v2013.07. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com>
2013-03-11Merge u-boot/master into u-boot-ti/masterTom Rini
In master we had already taken a patch to fix the davinci GPIO code for CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these conflicts manually and comment the #else/#endif lines for clarity. Conflicts: arch/arm/include/asm/arch-davinci/gpio.h drivers/gpio/da8xx_gpio.c Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11arm: dra7xx: Add silicon id support for DRA752 socLokesh Vutla
Adding CPU detection support for the DRA752 ES1.0 soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
generated by cgit (git 2.34.1) at 2025-01-07 18:07:59 +0000