summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-12-11exynos:cpu: Add Exynos4 I2C spacingPiotr Wilczek
This patch add the spacing for i2c for Exynos4 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11exynos:clock: Add i2c clockPiotr Wilczek
This patch adds i2c clock for Exynos4 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11omap24xx_i2c: Handle OMAP5 like OMAP2,3,4Vincent Stehlé
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same way. This fixes the following error on OMAP5: OMAP5430 EVM # mmc rescan timed out in wait_for_bb: I2C_STAT=1410 twl6035: could not turn on LDO9. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-11mxs: i2c: Implement algorithm to set up arbitrary i2c speedMarek Vasut
This algorithm computes the values of TIMING{0,1,2} registers for the MX28 I2C block. This algorithm was derived by using a scope, but the result seems correct. The resulting values programmed into the registers do not correlate with the contents in datasheet. When using the values from the datasheet, the I2C clock were completely wrong. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2012-12-11mxs: i2c: Restore speed setting after block resetMarek Vasut
The I2C block reset configures the I2C bus speed to strange value. Read the I2C speed from the block before reseting the block and restore it afterwards, so the I2C operates correctly. This issue can be replicated by doing unsuccessful I2C transfer, after such transfer finishes, the I2C block clock speed is misconfigured. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Fix TIMING2 register valueMarek Vasut
According to FSL, the value in the TIMING2 register shall be 0x00300030 instead of what's written in the datasheet. This new value correlates with older STMP36xx datasheet. Issues were detected in Linux when this register was misconfigured, so write this correct value. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Use i2c_set_bus_speed() in i2c_init()Marek Vasut
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver to avoid duplication of code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Implement i2c_get/set_bus_speed()Marek Vasut
This patch implements the setup and retrieval functions for the I2C bus speed on the MXS I2C IP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Abstract out the MXS I2C speed setupMarek Vasut
This patch pulls out the I2C speed setup from the i2c_init() call and implements the bus configuration lookup table with register values that needs to be programmed into the I2C IP to run at particular speed. This patch is a first step towards implementing run-time I2C bus speed configuration for the MXS I2C IP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: kerneldoc: Add kerneldoc annotations to cmd_i2c.cMarek Vasut
Add kerneldoc style documentation into cmd_i2c.c to properly describe all overridable functions and most of the command interface. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
2012-12-11i2c: Staticize local functions in mxc i2c driverMarek Vasut
Some functions in the MXC i2c driver were not static, fix this by making them so. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-12-11i2c: Use __weak instead of __attribute__((weak, alias))Marek Vasut
Use __weak from linux/compiler.h instead of __attribute__((weak, alias)) to define overridable function. This patch is intended as a cleanup patch to bring some consistency into the code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
2012-12-11soft_i2c: add necessary includes for AVR32Andreas Bießmann
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2012-12-11woodburn: Set gpio value in gpio_direction_output()Fabio Estevam
Set the gpio value in gpio_direction_output() instead of an extra gpio_set_value call. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-12-11mx25pdk: Adapt it for the new PMIC frameworkFabio Estevam
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can be built again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-12-11Correct comment to show the parameters as defined in tools/mkimage.hLars Rasmusson
Signed-off-by: Lars Rasmusson <Lars.Rasmusson@sics.se>
2012-12-11universal_c210: check the NULL pointer when get the PMICMinkyu Kang
PMIC 2.0 require to test return pointer from pmic_get() Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2012-12-11SMDK5250: Enable pmic MAX77686Rajeshwari Shinde
Enabled pmic MAX77686 for SMDK5250. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11POWER: MAX77686: Modified as per the latest ImplementationRajeshwari Shinde
Moved the pmic_max77686.c max77686_pmic.h to drivers/power and made required changes accordingly Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-10cm-t35: enable zero bootdelay checkNikita Kiryanov
Enable zero bootdelay check to make it possible to abort autoboot even if bootdelay == 0 Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2012-12-10power: twl6035: complain on LDO9 errorVincent Stehlé
We handle i2c_write return code and complain in case of error. We propagate the error, too, to allow better handling at the upper level in the future. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10omap24xx_i2c: Handle wait_for_bb errorVincent Stehlé
We add a return code to wait_for_bb() to be able to report errors to the callers properly. We in turn handle this new error code in i2c_read, i2c_write and i2c_probe. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10gpio: add gpio_is_valid() to omap_gpio APINikita Kiryanov
Add gpio_is_valid() to omap_gpio API Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-12-10OMAP3: Remove unused PHYS_SDRAM_1_SIZEThomas Weber
Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files. Signed-off-by: Thomas Weber <thomas@tomweber.eu>
2012-12-10am335x: cpsw: make phy address configurableYegor Yefremov
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10am335x: disable internal delay for RGMII modeYegor Yefremov
According to errata the AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10OMAP3: TAM3517: add macros for reading eepromStefano Babic
Added macros to read SOM information from the I2C EEPROM. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-12-10OMAP3: fix panel timing on the mt_ventoux boardStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-12-10davinci: fixed cpu resetDavide Bonfanti
The reset procedure works on watchdog timer while before it was modifying TIMER_1 registers. Tested on DM365. Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
2012-12-10OMAP3 SPI : Fixed bugs related to SPI transferajoy
Added posted writes (read after writes) to effect the change immediately for channel confiuration and channel enable register Disable the channel to purge receieve data in TX_ONLY mode transfer otherwise rx data will get affected by the next immediate RX_ONLY mode transfer Wait for the EOT bit to be set after last byte has been loaded to TX shift register in the the TX_ONLY mode.This ensures TX data has been completely shifted out Disable the channel in RX_ONLY mode before reading the last data from RXX register to prevent the SPI slave to transmit next word Signed-off-by: Ajoy Kumar Das <akdas75@yahoo.in> Cc: Tom Rini <trini@ti.com> Cc: jacopo mondi <j.mondi@voltaelectronics.com>
2012-12-10omap: emif: configure emif only when requiredLokesh Vutla
DMM_LISA_MAP registers program whether memory is mapped on particular EMIF or not. Irrespective of these registers EMIF is getting configured. Correcting the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-12-10OMAP: Tweak omap-common/Makefile since reset.S -> reset.cRobert P. J. Day
Git commit d417d1db5f9092d125ddea882ced77eaa5f3d236 replaced the omap-common file reset.S with reset.c, but the Makefile was not adjusted for that. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10omap4: Add comments on some "#endif"s for readability.Robert P. J. Day
No functional changes, simply for readability. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10omap3: Add a few comments to "#endif"s for readability.Robert P. J. Day
No functional changes, just more comments for readability when a preprocessor check spans more than a few lines, and for consistency. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10Pass sdrc timing values through board_sdrc_timings structurePeter Barada
Instead of passing individual registers by value to board_get_mem_timings, pass a board_mem_timings structure pointer for the board files to fill in. Pass same structure pointer to write_sdrc_timings. This saves about 90 bytes of space in SPL. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-12-10omap3_beagle.h: Fix comment for true/false return value.Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10am335x_evm: enable SPL NAND supportIlya Yanok
Enable booting from NAND support from AM335x boards as well as environment in NAND. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am33xx_spl_bch: simple SPL nand loader for AM33XXIlya Yanok
AM33XX with BCH8 can't work with nand_spl_simple correctly because custom read_page implementation is required for proper syndrome generation. This simple driver mostly duplicates nand_spl_simple but has nand_read_page changed to suit our needs. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10omap_gpmc: BCH8 support (ELM based)Mansoor Ahamed
This patch adds support for BCH8 error correction code to omap_gpmc driver. We use GPMC to generate codes/syndromes but we need ELM to find error locations from given syndrome. Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com> [ilya: merge it with omap_gpmc driver, some fixes and cleanup] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am33xx: add ELM supportMansoor Ahamed
AM33XX has Error Location Module (ELM) that can be used in conjuction with GPMC controller to implement BCH codes fully in hardware. This code is mostly taken from arago tree. Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com> Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am335x_evm: enable NAND supportIlya Yanok
Enable NAND support for AM335X boards. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am33xx: NAND supportIlya Yanok
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the existing omap_gpmc driver. This patch adds adds required definitions/intialization. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am335x_evm: add nand pinmux definitionIlya Yanok
Add NAND pins mux settings for AM335X devices. Enable NAND pins for AM335X EVM board. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10OMAP: include sys_proto.h from boot-commonIlya Yanok
Include asm/arch/sys_proto.h for gpmc_init prototype. Without this we get a warning while building for AM335x. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10omap3/mem.c: remove unused definesAndreas Bießmann
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954 removed the need for these definitions but missed to remove them. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com>
2012-12-10universal_c210: fix compiler error and compiler warningMinkyu Kang
This patch fix following errors universal.c: In function 'init_pmic_lcd': universal.c:340: warning: implicit declaration of function 'get_pmic' universal.c:340: warning: initialization makes pointer from integer without a cast universal.c: In function 'lcd_power_on': universal.c:431: warning: initialization makes pointer from integer without a cast universal.c: At top level: universal.c:335: warning: 'init_pmic_lcd' defined but not used Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Donghwa Lee <dh09.lee@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
2012-12-10Merge branch 'master' of git://git.denx.de/u-boot into resolveMinkyu Kang
Conflicts: README board/samsung/universal_c210/universal.c drivers/misc/Makefile drivers/power/power_fsl.c include/configs/mx35pdk.h include/configs/mx53loco.h include/configs/seaboard.h
2012-12-08MIPS: constify address pointer in test_bit()Daniel Schwierzeck
Fix several warnings when enabling UBIFS on MIPS: In file included from ubifs.h:2137:0, from ubifs.c:26: misc.h: In function 'ubifs_zn_dirty': misc.h:38:2: warning: passing argument 2 of 'test_bit' discards 'const' qualifier from pointer target type [enabled by default] ../include/asm/bitops.h:569:23: note: expected 'volatile void *' but argument is of type 'const long unsigned int *' Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-08MIPS: fix a latent bug on initialize $gpZhi-zhou Zhang
If bal is 8 bytes aligned, the _gp will not be 8 bytes aligned. then the following ld insntrustion generates a Adel exception. So here make _gp be always aligned in 8 bytes. Signed-off-by: Zhi-zhou Zhang <zhizhou.zh@gmail.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-08Merge branch 'master' of git://git.denx.de/u-boot into masterStefano Babic
Conflicts: drivers/power/power_fsl.c include/configs/mx35pdk.h include/configs/mx53loco.h include/configs/woodburn_common.h board/woodburn/woodburn.c These boards still use the old old PMIC framework, so they do not merge properly after the power framework was merged into mainline. Fix all conflicts and update woodburn to use Power Framework. Signed-off-by: Stefano Babic <sbabic@denx.de>
generated by cgit (git 2.34.1) at 2024-12-27 20:08:37 +0000