summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-02-01rockchip: Drop call to rockchip_dnl_mode_check() for nowSimon Glass
This function causes a 5-second delay and stops the display working on minnie. This code should be in a driver and should only be enabled by a device-tree property, so that it does not affect devices which do not have this feature. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01sound: rockchip: Add sound support for jerrySimon Glass
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral. Enable sound support and add the required device-tree pieces. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add a sound driverSimon Glass
Add a sound driver for rk3288 supporting chromebook_jerry. This uses the I2S driver, and existing audio codec and the clock/pinmux support. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add an I2S driverSimon Glass
Add a driver for I2S which allows audio data to be sent from the SoC to the audio codec. The sample rate and other settings are hard-coded for now as there is no suitable device-tree binding available. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: rk3288: Add i2s pinctrl and clock supportSimon Glass
Add support for setting pinctrl and clock for I2S on rk3288. This allows the sound driver to operate. These settings were created by rkmux.py Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01ARM: DTS: am43xx: Enable the DTS entries for USB port #2 in SPLJean-Jacques Hiblot
This is required to enable the USB port #2 in SPL when DM_USB is used. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-02-01ARM: DTS: am43xx: Add aliases for the USB portsJean-Jacques Hiblot
Although not required, it doesn't hurt to explicitly map the USB ports to a USB controller. Without this, the port number will be derived from the binding order of the peripheral devices. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-02-01ARM: DTS: Resync am3517-evm.dts with Linux 5.0-rc3Adam Ford
The chosen node was added in the kernel. This may come in handy in the future, so resync with 5.0-rc3 Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01ARM: dts: da850-evm: Re-sync with Kernel 5.0Adam Ford
Resync with Kernel 5.0-rc3 Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01ARM: am3517_evm: Enable DM_SPI and DM_USBAdam Ford
To comply with pending requirements, this sets the flags to enable DM_SPI and DM_USB. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01spl: fat/fs: Add control to build FS EXT4 in SPLTien Fong Chee
CONFIG_SPL_FS_EXT4 can be used to include/exclude the FS EXT4 from SPL build. Excluding the FS EXT4 from SPL build can help to save 20KiB memory. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4Tien Fong Chee
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01spl: fat/fs: Add option to include/exclude FAT write build in SPLTien Fong Chee
Most of the time SPL only needs very simple FAT reading, so having CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help to save 64KiB default max clustersize from memory. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FATTien Fong Chee
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01configs: removing am335x_evm_usbspl_defconfigJean-Jacques Hiblot
This feature is now supported by the main config for am335x_evm: am335x_evm_defconfig Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01configs: am335x_evm: enable DM_USB_GADGET and USB_ETHER in u-boot and SPLJean-Jacques Hiblot
The AM335x ROM boot is able to download the SPL from a RNDIS connection on USB0. To enable a full RNDIS boot flow (romboot -> SPL -> u-boot -> ..), we can use USB_ETHER in SPL and u-boot. However this increase the size of the SPL past its limit. So removing the unused SPL_EXT_SUPPORT. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01ARM: DTS: am335x-evm: Use USB0 in peripheral modeJean-Jacques Hiblot
This USB port is mainly used for RNDIS and DFU. To be able to use it with DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01usb: ether: call _usb_eth_halt() if initialization failsJean-Jacques Hiblot
If the host does not respond in time, the initialization fails. However the usb ether driver will still be registered. This will make usb_gadget_probe_driver() fail the next time the initialization is attempted because it cannot find an available UDC. Fixing this by calling _usb_eth_halt() when the init fails. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-02-01am335x, shc: adapt shc board to DMHeiko Schocher
port the am335x based shc board to DM, to get rid of DW warnings when compiling U-Boot. - remove uneccessary board code - adapt defconfigs - remove unneeded defconfigs configs/am335x_shc_prompt_defconfig configs/am335x_shc_sdboot_prompt_defconfig Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01ARM: dts: am335x-shc: add u-boot specific dtsiHeiko Schocher
add u-boot specific am335x-shc-u-boot.dtsi file, in which we add u-boot specific adaptions. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01arm: dts: add am335x-shc.dts for shc boardHeiko Schocher
add DTS from linux tree commit "47bfa6d9dc8c060bf56554a465c9031e286d2f80" change for U-Boot: switch to SPDX-license identifier. Signed-off-by: Heiko Schocher <hs@denx.de>
2019-02-01configs: mscc_luton: Add network support.Horatiu Vultur
Update default config to use network driver for Luton SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: Add MSCC Luton networkd driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch, it is present on Luton SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01mips: mscc: luton: Add ethernet nodes for Luton.Horatiu Vultur
Add nodes for pcb090 and pcb091. There is currently no support in Linux for this SoC. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Remove unused variablesHoratiu Vultur
Remove unused variables in the struct ocelot_private and make miim variable static. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move mac_table_add function into different file.Horatiu Vultur
Move the function mac_table_add into a different file, so it can be reused. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move ocelot_send and ocelot_recv in a different file.Horatiu Vultur
This functions can be reused by other MSCC SoCs therefore, make them more generic and move them in separate files. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move miim commands into separate file.Horatiu Vultur
Move miim functions that can be shared in a different file inside mscc_eswitch. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move ocelot_switch to mscc_eswitch folderHoratiu Vultur
Move file ocelot_switch to mscc_eswitch to prepare to add new net drivers for other MSCC SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01mips: mt76xx: Use correct timer frequencyStefan Roese
Testing has shown that the timer on the MT7688 platforms does not run correctly (too fast timeout). This patch changes CONFIG_SYS_MIPS_TIMER_FREQ from 200MHz to 290MHz which is the correct value, as its also used in Linux. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-02-01MSCC: Fix Jaguar2 board detection.Horatiu Vultur
When power cycle the Jaguar2 boards, it couldn't read the phys, therefore it always deduce that the board type is pcb111. Add a small delay after setting the gpio pins, fix the issue. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01MSCC: Jaguar2 enable debug uartHoratiu Vultur
Enable debug uart for Jaguar2 SoC family. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-31Merge tag 'video-updates-for-2019.04-rc1' of git://git.denx.de/u-boot-videoTom Rini
- ihs and imx driver fixes - relax EDID validation checks for 0 hsync/vsync pulse width (support some quirky displays)
2019-01-31Merge tag 'u-boot-amlogic-20190131' of git://git.denx.de/u-boot-amlogicTom Rini
- Add features and fixups to support video on Amlogic GX SoCs - Add video support for Amlogic GX SoC - Add DT fixups - Enable Video and USB Console for libretech-cc board
2019-01-31arm: libretech-cc: enable video by defaultMaxime Jourdan
libretech-cc being the main device tested with CONFIG_VIDEO_MESON, let's enable it by default. Also enable: - CONFIG_SYS_WHITE_ON_BLACK for prettiness - CONFIG_VIDEO_DT_SIMPLEFB for framebuffer sharing with kernel Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31arm: meson64: enable console mux and console env by defaultMaxime Jourdan
With the recent addition of the meson VPU driver, enable the following config entries by default for meson-64 targets: CONFIG_CONSOLE_MUX, CONFIG_SYS_CONSOLE_IS_IN_ENV. This allows outputting the console via video if CONFIG_VIDEO_MESON is selected. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31configs: meson64: use vidconsole and usbkbd if enabledNeil Armstrong
Allows displaying the console via video and using a USB keyboard. Also enables CONFIG_SPLASH_SCREEN if using video. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31arm: meson: board-gx: Setup VPU in fdtMaxime Jourdan
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer. Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for EFI, and sets up simple-framebuffer nodes if simplefb support is enabled. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31arm64: dts: meson-gx: add hhi reg entry to hdmi_txMaxime Jourdan
There's no reliable way to reuse the hhi entry from the vpu as is done in the linux kernel, so we duplicate it here. We will be able to sync against kernel DTS in the future when the VPU gets based on the clock framework rather than the HHI reg. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-01-31arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supplyNeil Armstrong
The hdmi_5v regulator must be enabled to provide power to the physical HDMI PHY and enables the HDMI 5V presence loopback for the monitor. Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> [backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
2019-01-31arm64: dts: meson-gx: vpu should be probed before relocationMaxime Jourdan
Flag the appropriate nodes with u-boot,dm-pre-reloc Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-01-31video: Add Meson Video Processing Unit DriverNeil Armstrong
This adds video output support for Amlogic GXBB/GXL/GXM chips. The supported ports are CVBS and HDMI (based on DW_HDMI). When using HDMI, only DMT modes are supported. There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB) Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> [narmstrong: fixed defines alignment in meson_canvas.c] Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31video: dw_hdmi: add support for color conversionJorge Ramirez-Ortiz
Some IPs like the meson VPU can only feed a particular pixel format to dw_hdmi. As of now, the driver is hardcoded to use RGB888 as input. This commit enables different pixel format inputs, with the appropriate CSC configuration. Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31video: dw_hdmi: support SoC specific read/write opsJorge Ramirez-Ortiz
Some IPs like the meson VPU have a specific way to write to dw_hdmi registers. Make it configurable. Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com> [added commit description] Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31power: domain: meson-gx-pwrc-vpu: add missing dependsMaxime Jourdan
MESON_GX_VPU_POWER_DOMAIN should depend on POWER_DOMAIN. Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-30MAINTAINERS: Add Amlogic entryNeil Armstrong
Add entry for Amlogic SoC maintained files and the freshly created mailing-list. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-01-30Makefile: remove generated font filesHeinrich Schuchardt
If `make mrproper` does not delete the generated drivers/video/fonts/*.S files a following `make tests` fails. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-30dfu: mmc: call fs functions instead of run_commandSimon Goldschmidt
This unbreaks dfu mmc_file_op which is currently broken since using the load cmd on a buffer from heap is not allowed - added with commit aa3c609e2be5 ("fs: prevent overwriting reserved memory") Fixes: commit aa3c609e2be5 ("fs: prevent overwriting reserved memory") Reported-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-30Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- Enable DM_MMC support
2019-01-30arm: sunxi: Enable DM_MMCJagan Teki
Enable DM_MMC for all Allwinner SoCs, this will eventually enable BLK. Also removed DM_MMC enablement in few parts of sunxi configurations. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
generated by cgit (git 2.34.1) at 2024-12-29 06:56:17 +0000