summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-10-06spi: fsl_qspi: Preserve endianness of QSPI MCRYork Sun
The endianness can be changed by RCW + PBI sequence. It may have other than power on reset value. Signed-off-by: York Sun <york.sun@nxp.com> CC: Yuan Yao <yao.yuan@nxp.com> CC: Peng Fan <peng.fan@nxp.com> CC: Alison Wang <alison.wang@nxp.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-06spl: Make spl_boot_list a local variableSimon Glass
There is no need for this to be in the BSS region. By moving it we can delay use of BSS in SPL. This is useful for machines where the BSS region is not in writeable space. On 64-bit x86, SPL runs from SPI flash and it is easier to eliminate BSS use than link SPL to run with BSS at a particular cache-as-RAM (CAR) address. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Update spl_load_simple_fit() to take an spl_image paramSimon Glass
Upda the SPL FIT code to use the spl_image parameter. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Update fat functions to take an spl_image parameterSimon Glass
Update the fat loader to avoid using the spl_image global variable. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Update ext functions to take an spl_image parameterSimon Glass
Update the ext loader to avoid using the spl_image global variable. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Pass spl_image as a parameter to load_image() methodsSimon Glass
Rather than having a global variable, pass the spl_image as a parameter. This avoids BSS use, and makes it clearer what the function is actually doing. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_board_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Update existing users. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_net_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. We need two variants - one for BOOT_DEVICE_CPGMAC and one for BOOT_DEVICE_USBETH. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spi: Move freescale-specific code into a private headerSimon Glass
At present there are two SPI functions only used by freescale which are defined in the spi_flash.h header. One function name matches an existing generic SPL function. Move these into a private header to avoid confusion. Arcturus looks like it does not actually support SPI, so drop the SPI code from that board. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_spi_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Also set up the sunxi function. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: spi: Move the generic SPI loader into common/splSimon Glass
All the other SPL loaders are in this directory, so move the SPI one in there too. There are two board-specific SPI loaders (fsl and sunxi). These remain in the drivers/mtd/spi directory, since they do not contain generic code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_sata_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_usb_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_ymodem_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_nor_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_onenand_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_nand_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_ubi_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_mmc_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert spl_ram_load_image() to use linker listSimon Glass
Add a linker list declaration for this method and remove the explicit switch() code. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Include updating the DFU case] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Add a way to declare an SPL image loaderSimon Glass
Add a linker list macro which can be used to declare an SPL image loader. Update spl_load_image() to search available loaders for the correct one. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Convert boot_device into a structSimon Glass
At present some spl_xxx_load_image() functions take a parameter and some don't. Of those that do, most take an integer but one takes a string. Convert this parameter into a struct so that we can pass all functions the same thing. This will allow us to use a common function signature. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Kconfig: Move SPL_DISPLAY_PRINT to KconfigSimon Glass
Move this option to Kconfig and tidy up existing uses. Also add a function comment to the header file. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Add function comments to spl_start_uboot()Simon Glass
Add some comments to describe this function. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Add a parameter to jump_to_image_linux()Simon Glass
Instead of using the global spl_image variable, pass the required struct in as an argument. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Add a parameter to spl_parse_image_header()Simon Glass
Instead of using the global spl_image variable, pass the required struct in as an argument. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Add a parameter to spl_set_header_raw_uboot()Simon Glass
Rather than act on the global variable, pass the required struct in as a parameter. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06spl: Move spl_board_load_image() into a generic headerSimon Glass
At present this is only used on ARM and sandbox, but it is just as applicable to other architectures. Move the function prototype into the generic SPL header. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06armv7: ls1021a: Move DDR config options to KconfigYork Sun
Move DDR3, DDR4 and related config options to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06armv8: fsl-layerscape: Move DDR config options to KconfigYork Sun
Move DDR3, DDR4 and realted options to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Move SYS_FSL_SRDS_* and SYS_HAS_SERDES to KconfigYork Sun
Move these options to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Move FSL_HAS_DP_DDR and NUM_DDR_CONTROLLERS to KconfigYork Sun
Move this option to Kconfig and clean up existing uses. NUM_DDR_CONTROLLERS is also used by PowerPC SoCs. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Move SYS_FSL_IFC_BANK_COUNT to KconfigYork Sun
Move this option to Kconfig and clean up existing uses. This option is also used by PowerPC SoCs. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Move MAX_CPUS to KconfigYork Sun
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This option is used by Freescale Layerscape SoCs. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Move FSL_LSCH2 FSL_LSCH3 to KconfigYork Sun
Move these options to Kconfig and create a sub-menu to avoid name conflict with other architectures. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06arm: Fix Kconfig for proper display menuYork Sun
Some config options should not have prompt. They are selected by choosing target. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06armv8: fsl: Enable USB only when SYSCLK is 100 MHzSriram Dash
SYSCLK is used as a reference clock for USB. When the USB controller is used, SYSCLK must meet the additional requirement of 100 MHz. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8: ls1043: Add USB node in dts for ls1043Sriram Dash
Add the USB node for LS1043 in dts. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8: ls1043: Enable CONFIG_DM_USB in defconfigsSriram Dash
Enables driver model flag CONFIG_DM_USB for LS1043A platform defconfigs. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8/fsl-lsch2: Implement workaround for PIN MUX erratum A010539Hou Zhiqiang
Pin mux logic has 2 options in priority order, one is through RCW_SRC and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT to control the SPI muxing. But actually those are DSPI controller's pads instead of QSPI controller's, so this workaround allows RCW fields SPI_BASE and SPI_EXT to control relevant pads muxing. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> [York Sun: Reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06ARMv7: LS102xA: Move two macros from header files to KconfigHongbo Zhang
Following commits 217f92b and 1544698, these two config CPU_V7_HAS_NONSEC and CPU_V7_HAS_VIRT are moved to Kconfig, for correctly select ARMV7_PSCI. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> [York Sun: Reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8: fsl-layerscape: Fix "cpu status" commandYork Sun
The core position is not continuous for some SoCs. For example, valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some registers (including boot release register) only count existing cores. Current implementation of cpu_mask() complies with the continuous numbering. However, command "cpu status" queries the spin table with actual core position. Add functions to calculate core position from core number, to correctly calculate offsets. Tested on LS2080ARDB and LS1043ARDB. Signed-off-by: York Sun <york.sun@nxp.com>
2016-10-06armv8/fsl-layerscape: print SoC revsion numberWenbin Song
The exact SoC revsion number can be recognized from U-Boot log. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06fsl_sfp : Modify macros as per changes in SFP v3.4Sumit Garg
SFP v3.4 supports 8 keys in SRK table which leads to corresponding changes in OSPR key revocation field. So modify OSPR_KEY_REVOC_XXX macros accordingly. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv7: LS1021a: enable i-cache in start.SXiaoliang Yang
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First stage of u-boot can run faster after that. There is a description about skip lowlevel init in board/freescale/ls1021atwr/README. Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06fsl_sec_mon: Update driver for Security MonitorSumit Garg
Update the API's for transition of Security Monitor states. Instead of providing both initial and final states for transition, just provide final state for transition as Security Monitor driver will take care of it internally. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> [York Sun: Reformatted commit message slightly] Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8: fsl-lsch2: enable snoopable sata read and writeTang Yuantian
By default the SATA IP on the ls1043a/ls1046a SoCs does not generating coherent/snoopable transactions. This patch enable it in the SCFG_SNPCNFGCR register along with sata axicc register. In addition, the dma-coherent property must be set on the SATA controller nodes. Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> [York Sun: Reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06armv8: fsl-lsch2: adjust sata parameterTang Yuantian
The default values for Port Phy2Cfg register and Port Phy3Cfg register are better, no need to overwrite them. Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06serial: ns16550: Handle -ENOENT when requesting clockAlexandre Courbot
When calling clk_get_by_index(), fall back to the legacy method of getting the clock if -ENOENT is returned. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com>
2016-10-06udoo: Add a README fileFabio Estevam
Add a README file to explain how to build and flash the SD card for Udoo boards. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-30 14:29:19 +0000