summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-06-03arm: vf610: Add watchdog support for Vybrid VF610Alison Wang
This patch adds watchdog support for Vybrid VF610 platform. Signed-off-by: Alison Wang <b18965@freescale.com>
2013-06-03net: fec_mxc: Add support for Vybrid VF610Alison Wang
This patch adds FEC support for Vybrid VF610 platform. In function fec_open(), RCR register is only set as RGMII mode. But RCR register should be set as RMII mode for VF610 platform. This configuration is already done in fec_reg_setup(), so this piece of code could just leave untouched the FEC_RCNTRL_RGMII / FEC_RCNTRL_RMII / FEC_RCNTRL_MII_MODE bits. Signed-off-by: Alison Wang <b18965@freescale.com> Reviewed-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-03arm: vf610: Add Vybrid VF610 CPU supportAlison Wang
This patch adds generic codes to support Freescale's Vybrid VF610 CPU. It aligns Vybrid VF610 platform with i.MX platform. As there are some differences between VF610 and i.MX platforms, the specific codes are in the arch/arm/cpu/armv7/vf610 directory. Signed-off-by: Alison Wang <b18965@freescale.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-03arm: vf610: Add IOMUX support for Vybrid VF610Alison Wang
This patch adds the IOMUX support for Vybrid VF610 platform. There is a little difference for IOMUXC module between VF610 and i.MX platform, the muxmode and pad configuration share one 32bit register on VF610, but they are two independent registers on I.MX platform. A CONFIG_IOMUX_SHARE_CONFIG_REG was introduced to fit this difference. Signed-off-by: Alison Wang <b18965@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-30arm: factorize relocate_code routineAlbert ARIBAUD
Replace all relocate_code routines from ARM start.S files with a single instance in file arch/arm/lib/relocate.S. For PXA, this requires moving the dcache unlocking code from within relocate_code into c_runtime_cpu_setup. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30arm: do not compile relocate_code() for SPL buildsAlbert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30tx25: copy SPL directly, not using relocate_code.Albert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30mx31pdk: copy SPL directly, not using relocate_code.Albert ARIBAUD
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
2013-05-28tegra: Define CONFIG_SKIP_LOWLEVEL_INIT for SPL buildAxel Lin
Then we can get rid of the #ifdef CONFIG_TEGRA guard in cpu_init_crit. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28ARM: arm720t: Add missing CONFIG_SKIP_LOWLEVEL_INIT guard for cpu_init_critAxel Lin
cpu_init_crit() can be skipped, but the code is still enabled requiring a platform to supply lowlevel_init(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28ARM: tegra: support SKU 7 of Tegra20Stephen Warren
Make U-Boot aware of the Tegra20 SKU 7, and treat it identically to any other Tegra20. My Whistler board has a SoC with this SKU. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28ARM: tegra: support SKU 1 of Tegra114Stephen Warren
Make U-Boot aware of the Tegra114 SKU 1, and treat it identically to any other Tegra114. This value is used on (at least some) Dalmore boards with a production rather than engineering chip. Such boards are in the hands of some partners who want to use upstream U-Boot. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28tegra: always build u-boot-nodtb-tegra.binStephen Warren
Even when eventually building u-boot-dtb-tegra.bin, separately building u-boot-nodtb-tegra.bin can be useful, since building it encapsulates the SPL padding step. If you want to tweak u-boot.dtb and regenerate u-boot-dtb-tegra.bin, it is then a simple cat operation. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28Tegra: clk: always use find_best_divider() for periph clocksAllen Martin
When adjusting peripheral clocks always use find_best_divider() instead of clk_get_divider() even when a secondary divider is not available. In the case where is requested clock is too slow to be derived from the parent clock this allows a best effort to get close to the requested clock. This comes up for commands like "sf" where the user can pass a clock speed on the command line or "sspi" where the clock is hardcoded to 1MHz, but the Tegra114 SPI controller can't go that low. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-05-28Tegra: Remove unused/non-existent spl linker script referenceTom Warren
Tegra builds use the common u-boot-spl.lds now. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-05-28Tegra: T30: Beaver: Fix board/board_name env vars, s/b beaver, not cardhuTom Warren
Did a 'strings u-boot-dtb-tegra.bin | less' and saw that both board and board_name == beaver. Didn't test as I have no T30 Beaver board here. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com>
2013-05-24powerpc/mpc85xx: Clear L1 D-cache lockYork Sun
dcbi instruction has been used to clear D-cache lock. However, the cache lock is persistent for e6500 core. Use dcblc to clear the lock explicitly. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24SECURE BOOT - Removed deletion of TLB entries codeRuchika Gupta
Boot ROM code creates TLB entries for 3.5G space before entering the u-boot. Earlier we were deleting these entries after early initialization of CPU. In recent past, code has been added to invalidate all these entries before relocation of u-boot code. So this code to delete TLB entries after CPU initialization is no longer required. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Acked-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/b4860qds: Add LAW Target ID and Create LAW entry for MapleShaveta Leekha
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p5040: fix mdio mux for 10G portShaohui Xie
Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in eth port enum structure, it will assign mdio mux depend on this assumption. This is not true with Fman V3, which added more 1G ports after port DTSEC5 in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux. So we use dynamic index for 10G ports instead of hardcoded enum value when doing mdio mux for 10G ports. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.hPoonam Aggrwal
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify the defines. - Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere. - defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G. Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24sf: spansion: Add support for S25FL128SXie Xiaobo
SPANSION recommend S25FL128S supersedes S25FL129P, and the two flash memory have the same device ID and Memory architecture. So they can use the same config parameters. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p2041: fix serdes reference clock frequency display for PC boardShaohui Xie
PC board has different serdes clock setting with PB board, it uses same serdes frequency setting on bank2 as on bank1. PC board can be distingushed from PB board by checking CPLD version, if running on PC board, then fix the serdes reference clock frequency of bank2. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/b4860: fix for Serdes connectivity to SFP'sShaveta Leekha
Crossbar switches were wrongly programmed to route the CPRI lanes to SFP as the connectivity table was not correct. Modified it correctly for SFPs connections. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4240qds: fix PHY reset timeout issueShengzhou Liu
QSGMII card has different PHY address against previous SGMII card. We check the type of card in slots and set correct PHY address to avoid complainning "PHY reset timed out" during u-boot booting up. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4qds: Add SW7[4] in the DIP switch displayYork Sun
SW7[4] is the new bit which controls the mapping of eMMC vs SDHC. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Enable XAUI interface for B4860QDSSuresh Gupta
- Added SERDES2 PRTCLs = 0x98, 0x9E - Default Phy Addresses for Teranetics PHY on XAUI card The PHY addresses of Teranetics PHY on XAUI riser card are assigned based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1 and slot2 - Configure MDIO for 10Gig Mac Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32MStephen George
Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p5040: enable PBL tool supportShaohui Xie
Provided a default RCW for P5040, then it can use PBL to build ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4qds: use clock measurement for sysclk and ddr clockEd Swarthout
Use QIXIS measurement registers to obtain sysclk and ddr clock. This allows using non-standard clock speeds, set by directly writing to clock chip or store the values in qixis clock data eeprom. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/qixis: add clock measurement registersEd Swarthout
QIXIS includes frequency measurement functions for each major processor clock input. After reset (and after clocks are stable), QIXIS measures the clocks against a reference frequency and stores the results in CLK_FREQ registers. A base register supplies a multiplier which allows directly obtaining the measured value, without requiring knowledge of the target system or QIXIS core frequency. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc8xxx: Allow DDR overclockYork Sun
Allow DDR clock runs faster than SPD specifes. This may cause memory failure, but the user should know what is going to happen when using higher than expected DDR clock. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/chassis2: Change core numbering schemeYork Sun
To align with chassis generation 2 spec, all cores are numbered in sequence. The cores may reside across multiple clusters. Each cluster has zero to four cores. The first available core is numbered as core 0. The second available core is numbered as core 1 and so on. Core clocks are generated by each clusters. To identify the cluster of each core, topology registers are examined. Cluster clock registers are reorganized to be easily indexed. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc8xxx: Add T1040 and variant SoCsYork Sun
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis Generation 2. The major difference between T1040 and its variants is the number of cores and the number of L2 switch ports. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.hYork Sun
T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p5040: enable NAND, SD, SPI boot supportShaohui Xie
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Add e6500 L2 replacement policy selectionJames Yang
This is compile-time config. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24T4240/ramboot: enable PBL tool for T4240Shaohui Xie
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use PBL tool to produce the ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4240qds: Add VDD overrideYork Sun
Allow VDD voltage overriding with a command. This is an add-on feasture of VID. To override VDD, use command vdd_override with the value of voltage in mV, for example vdd_override <voltage in mV, eg. 1050> The above example will set the VDD to 1.050 volt. Any wrong value out of range of 0.8188 to 1.2125 volt or invalid string is ignored. In addition to the command, if overriding VDD is needed earlier in booting process, save an variable and reboot: setenv t4240qds_vdd_mv <voltage in mV> saveenv Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc85xx: check if core is disabled for showing statusYork Sun
"cpu <num> status" should check if core is disabled before printing the spin table location. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24net/phy: fix select line for TN80xxShaohui Xie
TN80xx has same PHY ID as TN2020, but it needs different setting to register 30.93 which used to select line, so we read register 30.32 which has bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2, for TN80xx we will get 5 or 4. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Enable L2 cache parity/ECC error checkingJames Yang
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4240qds: Add board detail for bdinfo commandYork Sun
Print more detail information including core voltage, RCW source, switch settings, etc. with bdinfo command. Signed-off-by: York Sun <yorksun@freescale.com> CC: Wolfgang Denk <wd@denx.de> CC: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24common: Update cmd_bdinfo for PPCYork Sun
Add board detail function to print more individual board information. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24cmd_mem: fix cp commandMasahiro Yamada
The "cp" command has not worked since commit 0628ab8ec59834f98ede267edd21ddb8ba0bb57b, because of the following lines, which set the destination and the source to the same address. buf = map_sysmem(addr, bytes); src = map_sysmem(addr, bytes); Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-05-24ext4: assign get_fs()->dev_desc before using itStephen Warren
Commit 50ce4c0 "fs/ext4: Support device block sizes != 512 bytes" modified ext4fs_set_blk_dev() to calculate total_sect based on get_fs()->dev_desc->log2blksz rather than SECTOR_SIZE. However, this value wasn't yet assigned. Move the assignment earlier so the code doesn't crash or hang. Cc: Egbert Eich <eich@suse.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-05-23arm: Enable -ffunction-sections / -fdata-sections / --gc-sectionsTom Rini
While other architectures have enabled these gcc / ld options for some time on U-Boot itself, ARM has only been doing this on SPL. Enable this on full U-Boot as well now. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@ti.com>
2013-05-23ARM: Add Seagate GoFlex Home supportSuriyan Ramasami
Add Seagate GoFlex Home support Start with dockstar configuration define support for RTC, DATE, SATA and EXT4FS Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
2013-05-23ARM: vexpress: enable bootz and hush parser for all VExpress boardsAndre Przywara
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
generated by cgit (git 2.34.1) at 2024-12-30 21:23:13 +0000