summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk
2009-07-13Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk
2009-07-13issue write command to base for JEDEC flashPo-Yu Chuang
For JEDEC flash, we should issue word programming command relative to base address rather than sector base address. Original source makes SST Flash fails to program sectors which are not on the 0x10000 boundaries. e.g. SST39LF040 uses addr1=0x5555 and addr2=0x2AAA, however, each sector is 0x1000 bytes. Thus, if we issue command to "sector base (0x41000) + offset(0x5555)", it sends to 0x46555 and the chip fails to recognize that address. This patch is tested with SST39LF040. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-12versatile: update config and merge to cfi flash driverJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Peter Pearse <peter.pearse@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com>
2009-07-12versatile: specify the board type on the promptJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Peter Pearse <peter.pearse@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com>
2009-07-12at91: Introduction of at91sam9g10 SOC.Sedji Gaouaou
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a faster clock speed: 266/133MHz. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12at91: Introduction of at91sam9g45 SOC.Sedji Gaouaou
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz. It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of peripherals. The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. On the board you can find 2 USART, USB high speed, a 480*272 LG lcd, ethernet, gpio/joystick/buttons. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12pxa: fix CKEN_B register bitsDaniel Mack
The current defition for CKEN_B register bits is nonsense. Adding 32 to the shifted value is equal to '| (1 << 5)', and this bit is marked 'reserved' in the PXA docs. Signed-off-by: Daniel Mack <daniel@caiaq.de>
2009-07-12pxa: add clock for system bus 2 arbiterDaniel Mack
This clock is needed for systems using the USB2 device unit or the 2d graphics accelerator. Signed-off-by: Daniel Mack <daniel@caiaq.de>
2009-07-12OMAP3 pandora: Fix CKE1 MUX setting to allow self-refreshGrazvydas Ignotas
Pandora is using both SDRC CSes. The MUX setting is needed for the second CS clock signal to allow the 2 RAM parts to be put in self-refresh correctly. Based on similar patch for beagle and overo by Jean Pihet and Steve Sakoman.
2009-07-12OMAP3 pandora: setup pulls for various GPIOsGrazvydas Ignotas
Set pullups or pulldowns for GPIOs which need them. Disable them for others, which have external pulls. Also make disabled pull setting consistent (some pins had type set to "up" even if pull type selection was disabled).
2009-07-12OMAP3 pandora: setup pin mux for pins used on rev3 boardsGrazvydas Ignotas
Setup pin mux for GPIO pins connected on rev3 or later boards. Also change NUB2 IRQ pin. This should not affect older boards because they don't have any nubs (analog controllers) attached to them.
2009-07-12OMAP3 pandora: pin mux cleanupGrazvydas Ignotas
Remove configuration of not unused pins, effectively leaving them in safe mode.
2009-07-12arm: Kirkwood: bugfix: UART1 bar correctionPrafulla Wadaskar
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-07-11usb: Fix compiler warning with gcc4.4Kumar Gala
ehci-hcd.c: In function 'ehci_submit_root': ehci-hcd.c:719: warning: value computed is not used ehci-hcd.c:748: warning: value computed is not used Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-11sh: Update pci config for Renesas r7780mp boardNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-07-11sh: Add support ESPT-GIGA boradNobuhiro Iwamatsu
ESPT-Giga is SH7763-based reference board. Board support is relatively sparse, presently supporting serial, gigabit ethernet, USB host, and MTD. More information (in Japanese) available at: http://www.cente.jp/product/cente_hard/ESPT-Giga.html Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-07-10Blackfin: cm-bf561: add example settings for EXT-BF5xx-USB-ETH2 add-onHarald Krapfenbauer
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender board, so add a simple example of how to do that in the board config. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-10Blackfin: blackstamp: update spi flash settingsMike Frysinger
The latest blackstamp boards can only run the SPI flash at 15MHz before they start to crap out, so lower the max speeds accordingly. The new SPI flash also has different sector requirements, so update the environment sizes as well. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-10Blackfin: add cache_dump commandsMike Frysinger
A few debug-type commands used to dump the raw icache/dcache data. Useful when trying to track down cache-related bugs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-10ppc4xx: Set default PCI device ID for 405EP boardsMatthias Fuchs
Current code only sets the PCI vendor id to 0x1014 and leaved device id to 0x0000. Ths patch .... a) uses the correct PCI_VENDOR_ID_IBM macro for this b) sets the default device ID as stated in the UM to 0x0156 by using PCI_DEVICE_ID_IBM_405GP for this. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-10ppc4xx: Move 405EP pci code from cpu_init_f() to __pci_pre_init()Matthias Fuchs
This patch moves some basic PCI initialisation from the 4xx cpu_init_f() to cpu/ppc4xx/4xx_pci.c. The original cpu_init_f() function enabled the 405EP's internal arbiter in all situations. Also the HCE bit in cpc0_pci is always set. The first is not really wanted for PCI adapter designs and the latter is a general bug for PCI adapter U-Boots. Because it enables PCI configuration by the system CPU even when the PCI configuration has not been setup by the 405EP. The one and only correct place is in pci_405gp_init() (see "Set HCE bit" comment). So for compatibility reasons the arbiter is still enabled in any case, but from weak pci_pre_init() so that it can be replaced by board specific code. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-10ppc4xx: Make is_pci_host() available for all 440 and 405 CPUsMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-09usb: add Marvell Kirkwood ehci host controller driverPrafulla Wadaskar
This driver is tested on Sheevaplug platform Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09mpc83xx: USB: fix: access of ehci struct elementsVivek Mahajan
It fixes the access to the 'ehci' struct elements for mpc83xx which should have been taken care of in 4ef01010aa4799c759d75e67007fdd3a38c88c8a Sorry about that. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09mpc8xxx: USB: fix: access of ehci struct elementsVivek Mahajan
This patch fixes the access to the 'ehci' struct elements which should have been taken care off in 4ef01010aa4799c759d75e67007fdd3a38c88c8a Sorry about that. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09usb: musb: add timeout via CONFIG_MUSB_TIMEOUTBryan Wu
Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09usb: musb: drop old musb read/write prototypesMike Frysinger
These functions are no longer defined, so remove their prototypes. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09usb: fix CONFIG_SYS_MPC83xx_USB_ADDR not defined errorKim Phillips
fix a stray CONFIG_MPC83XX that escaped commit 0f898604945af4543c1525fc33b6bae621a3b805. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09Command improvements for ubifsSimon Kagstrom
Check that an argument is passed to ubifsmount and that addresses and sizes are actually numbers for ubifsload. Also improve the instructions a bit. Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-09Handle VID header offset in ubi part commandSimon Kagstrom
The VID header offset is sometimes needed to initialize the UBI partition. This patch adds it (optionally) to the command line for the ubi part command. (Lines have been properly wrapped since last version) Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-09MAINTAINERS: fix sorting, remove duplicates.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-08Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2009-07-08Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2009-07-08Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2009-07-08all platforms: make show_boot_progress() work againHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2009-07-08nand: Add Marvell Kirkwood NAND driverPrafulla Wadaskar
This patch adds a NAND driver for the Marvell Kirkwood SoC's Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Scott Wood <scottwood@freescale.com>
2009-07-08ppc4xx: Make pll_write globalMatthias Fuchs
This patch makes pll_write on PPC405EP boards global and callable from C code. pll_write can be used to dynamically modify the PLB:PCI divider as it is required for 33/66 MHz pci adapters based on the 405EP. board_early_init_f() is a good place to do that (check M66EN signal and call pll_write() when it is required). Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08ppc4xx: Remove compilation warning "pci_async_enabled defined but not used"Stefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08ppc4xx: Implement is_pci_host() for 405 CPUsMatthias Fuchs
This patch implements the is_pci_host() function in a similiar way as it is used on 440 targets. The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not build on 405EP targets because checking the PCI arbiter is different. So putting the fixed code into a separate function makes the code more readable. Also using is_pci_host() on 405 brings 405 and 440 PCI code a little bit closer. In preparation for an upcoming 405EP based PMC module I made this function weak so that it can be overwritten from board specific code. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08ppc4xx: Fixed PPC4xx debug compilation error in uic.cAlessio Centazzo
This patch fixes a debug compilation error for PPC4xx platforms, all other architectures are not affected by this change. The 'handler' pointer was undefined. The fix is exercised and has effect only if DEBUG is defined. Signed-off-by: Alessio Centazzo acpatin@yahoo.com Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-084xx: Fix compilation warnings and MQ registers dump in SPD DDR2 codeFelix Radensky
This patch fixes printf format string compilation warnings in several debug statements. It also fixes the dump of DDR controller MQ registers found on some 44x and 46x platforms. The current register dump code uses incorrect DCRs to access these registers. Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08ppc4xx: Fix FDT EBC mappings on CanyonlandsFelix Radensky
This patch fixes 2 problems with FDT EBC mappings on Canyonlands. First, NAND EBC mapping was missing, making Linux NAND driver unusable on this board. Second, NOR remapping code assumed that NOR is always on CS0, however when booting from NAND NOR is on CS3. Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08sh: Revised the build with newest compilerNobuhiro Iwamatsu
The check of data became severe from newest gcc. This patch checked in gcc-4.2 and 4.3 . Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-07-08sh3/sh4: rename config option TMU_CLK_DIVIDER to CONFIG_SYS_TMU_CLK_DIVJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>