summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-11-13sunxi: use 6MHz PLL_VIDEO step for DE2 for higher resolution LCDIcenowy Zheng
DE2 SoCs can support LCDs up to 1080p (e.g. A64), and 3MHz step won't let PLL_VIDEO be high enough for them. Use 6MHz step for PLL_VIDEO when using DE2, to satisfy 1080p LCD. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-13board: allwinner: sun50i-h6: Add Orangepi Lite2 supportJagan Teki
OrangePi Lite2 is Allwinner H6 based open-source SBC, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB LPDDR3 RAM - AXP805 PMIC - AP6356S Wifi/BT - USB 2.0, USB 3.0 Host, OTG - HDMI port - 5V/2A DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13arm64: allwinner: h6: Add common orangepi nodes into dtsiJagan Teki
Based on the information from hardware schematics and orangepi vendor orangepi H6 boards, One Plus and Lite2 shares common nodes like axp805, uart, mmc0 etc. The common differences between them is - One Plus, has Ethernet - Lite2, has Wifi, USB3, CSI port. So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that it case use on respective orangepi h6 board dts files. Cc: zhaoyifan <zhao_steven@263.net> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13sunxi: DT: add support for PinebookVasily Khoruzhick
Pinebook is a laptop produced by Pine64, with USB-connected keyboard, USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP bridge from Analogix. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sun50i: A64: add support for R_I2C controllerVasily Khoruzhick
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has two groups of pinmuxes on PL bank, so it's called R_I2C. Add support for this I2C controller and the pinmux which doesn't conflict with RSB. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Vagrant Cascadian <vagrant@debian.org> Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-13dm: video: bridge: don't fail to activate bridge if reset or sleep GPIO is ↵Vasily Khoruzhick
missing Both GPIOs are optional, so we shouldn't fail if any is missing. Without this fix reset is not deasserted if sleep GPIO is missing. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Cc: Vagrant Cascadian <vagrant@debian.org>
2018-11-13mmc: sunxi: add support for automatic delay calibrationVasily Khoruzhick
A64 and H6 support automatic delay calibration and Linux driver uses it instead of hardcoded delays. Add support for it to u-boot driver. Fixes eMMC instability on Pinebook Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Tested-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Cc: Vagrant Cascadian <vagrant@debian.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sunxi: A64: Add Pine64-LTS boardAndre Przywara
The Pine64 LTS is an updated version of the Pine64, copying the technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and soldered SPI flash chip, even the broken SD card detect pin has been copied. Consequently this leads to the .dts (copied from the kernel) just including the SoPine baseboard .dts, and the defconfig being almost identical. Nevertheless the boards deserves a separate config. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sunxi: H3/H5: Update .dts filesAndre Przywara
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree: commit 679294497be31596e1c9c61507746d72b6b05f26 Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz> Date: Wed Sep 26 19:48:24 2018 +0000 arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sunxi: A64: Re-add syscon to DT nodeAndre Przywara
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the compatible name for the syscon controller, dropping the generic "syscon" fallback. Using this new DT node will make the Ethernet driver in every older kernel (or non-Linux kernels) fail to initialise the MAC device. To allow booting distribution kernels (from installer images via UEFI, for instance), re-add the syscon compatible string as a fallback. This works with both older and newer kernels. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sunxi: A64: Update .dts/.dtsi filesAndre Przywara
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree: commit 679294497be31596e1c9c61507746d72b6b05f26 Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz> Date: Wed Sep 26 19:48:24 2018 +0000 arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13sunxi: Imply fitImage supportMarek Vasut
Enable modern fitImage format on sunxi. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Tom Rini <trini@konsulko.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13mtd: Drop duplicate MTD_PARTITIONS Kconfig optionBoris Brezillon
Commit 9c5b00973bce ("Convert CONFIG_MTD_PARTITIONS et al to Kconfig") introduced a publicly visible Kconfig entry for the CONFIG_MTD_PARTITIONS option, while the rework on MTD partitioning was in progress, and we somehow did not notice that the same Kconfig entry was added by commit 4048a5c519a8 ("mtd: declare MTD_PARTITIONS symbol in Kconfig"), but this time as an invisible entry (this can only be selected by other options). Keep the non-visible version of this symbol, since MTD_PARTITIONS is not something the user should be able to enable/disable directly. Fixes: 4048a5c519a8 ("mtd: declare MTD_PARTITIONS symbol in Kconfig") Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13cmd: ubi: Remove useless call to mtdparts_init()Boris Brezillon
Commit c58fb2cdb3e4 ("cmd: ubi: clean the partition handling") introduced a call to mtd_probe_devices() in the ubi_attach() path and this function takes care of parsing mtdparts/mtdids and creating/registering the associated mtd partitions. The mtdparts_init() call in the ubi_detach() path is not only unnecessary but can sometimes print error messages even when things work properly (that's the case with SPI NAND devices that have not been probed with 'mtd list'), which is misleading. Remove this call to mtdparts_init() and drop the dependency on CMD_MTDPARTS. Fixes: c58fb2cdb3e4 ("cmd: ubi: clean the partition handling") Reported-by: Stefan Roese <sr@denx.de> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13mtd: Make {MTDIDS, MTDPARTS}_DEFAULT visible when MTD_PARTITIONS is selectedBoris Brezillon
gwventana configs are relying on CMD_UBI to select CMD_MTDPARTS, which is then making {MTDIDS,MTDPARTS}_DEFAULT options available. We are about to remove the 'select CMD_MTDPARTS' statement in the CMD_UBI entry, but if we do that without first making sure {MTDIDS,MTDPARTS}_DEFAULT are visible, we end up with a build failure when building gwventana configs. Address that by adding a depends on MTD_PARTITIONS to {MTDIDS,MTDPARTS}_DEFAULT which does the trick since CMD_UBI selects MTD_UBI which in turn selects MTD_PARTITIONS. We also get rid of the depends on CMD_MTD, since CMD_MTD also selects MTD_PARTITIONS. Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13dfu: nand: Add missing dependency on CMD_MTDPARTSBoris Brezillon
dfu_fill_entity_nand() uses find_dev_and_part() and mtdparts_init() which are provided by cmd/mtdparts.c. Add the dependency to avoid build failures when CMD_MTDPARTS is not selected. Reported-by: Jagan Teki <jagan@amarulasolutions.com> Fixes: 6828e602b722d ("dfu: Migrate to Kconfig") Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13mtd: Use default mtdparts/mtids when not defined in the environmentBoris Brezillon
U-boot provides a mean to define default values for mtdids and mtdparts when they're not defined in the environment. Patch mtd_probe_devices() to use those default values when env_get("mtdparts") or env_get("mtdids") return NULL. This implementation is based on the logic found in cmd/mtdparts.c. Fixes: 5db66b3aee6f ("cmd: mtd: add 'mtd' command") Reported-by: Stefan Roese <sr@denx.de> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-12Merge tag 'u-boot-imx-20181112' of git://git.denx.de/u-boot-imxTom Rini
Fix build vf boards + fix gpr_init()
2018-11-12imx: mkimage: add size check to the u-boot.imx make targetMarcel Ziswiler
The make macro to check if the binary exceeds the board size limit is taken straight from the root Makefile. Without this and e.g. enabled EFI Vybrid fails booting as the regular size limit check does not take the final u-boot.imx binary size into account which is bigger due to alignment as well as IMX header stuff. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2018-11-12board: toradex: colibri_vf: drop SPI supportMarcel Ziswiler
Drop SPI support saving precious 4 Kb on boards with tough size restrictions. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2018-11-12board: toradex: colibri_vf: unset CONFIG_CMDLINE_EDITINGMarcel Ziswiler
Unset CONFIG_CMDLINE_EDITING saving precious 4 Kb on boards with tough size restrictions. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-11-12board: toradex: colibri_vf: efi_loader: unset CONFIG_EFI_UNICODE_CAPITALIZATIONMarcel Ziswiler
Unset CONFIG_EFI_UNICODE_CAPITALIZATION on boards with tough size restrictions. This is analogous to commit a90bf07afc43 ("efi_loader: unset CONFIG_EFI_UNICODE_CAPITALIZATION"). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-11-10mmc: dw_mmc: Add RCRC handlingMarek Vasut
This patch adds check for command response CRC failure. The driver is currently ignoring CRC check failure on command resposes which have CRC atteched to it, which can be potentially dangerous. Even more grueling problem happens when the command response is followed by data transfer though, as in that case, the dwmci_data_transfer() function will spin until it reaches the 240s timeout. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-11-09common: build ymodem only on needJun Nie
Build ymodem only on need to shrink spl image size. Signed-off-by: Jun Nie <jun.nie@linaro.org>
2018-11-09common: Compile error with CONFIG_MULTI_DTB_FIT and not SPLLars Povlsen
common/common_fit.c is including <spl.h>, but not actually using it. The inclusion will cuase compile error on platforms using CONFIG_OF_SEPARATE and not SPL. Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com> Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-11-09dm: Fix typo - missed semicolonAndy Shevchenko
The commit 484fdf5ba058 ("dm: Add support for all targets which requires MANUAL_RELOC") introduces subtle typo, i.e. missed semicolon. Fixes: 484fdf5ba058 ("dm: Add support for all targets which requires MANUAL_RELOC") Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2018-11-09spl: fix debug prints for tiny printfSimon Goldschmidt
Tiny printf does not support %.*s and %lX. Since tiny printf should be very common in SPL, replace these by %32s (for printing image name) and %lx. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-09MAINTAINERS: Update stm32mp entryPatrick Delaunay
Add mailing list for stm32mp architecture and board. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-11-09fit: Add missing CR in debug output in fit_find_config_node()Stefan Roese
Testing has shown that a line-break is missing in one debug line in fit_find_config_node(). Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-08imx: imx6: perform gpr_init only on suitable cpu typesChristoph Niedermaier
If the function gpr_init is used in a common MX6 spl implementation we have to ensure that it is only called for suitable cpu types, otherwise it breaks hardware parts like enet1, can1, can2, etc. Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.de>
2018-11-08Merge branch 'master' of git://git.denx.de/u-boot-ubiTom Rini
2018-11-07imx8qxp_mek: Disable CONFIG_DISPLAY_CPUINFOBin Meng
Due to revert of commit c0434407b595, this board does not build any more. Disable CONFIG_DISPLAY_CPUINFO for v2018.11 release. This commit should be reverted after v2018.11 release. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-07Revert "board_f: Use static print_cpuinfo if CONFIG_CPU is active"Bin Meng
This reverts commit c0434407b595f785fc7401237896c48c791b45fd. It turns out commit c0434407b595 broke some boards which have DM CPU driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail to boot when print_cpuinfo() is called during boot. Fixes are already sent to ML and in u-boot-dm/next, however since we are getting close to the v2018.11 release, it's safer we revert the original commit. This commit should be reverted after v2018.11 release. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-07Merge tag 'xilinx-for-v2018.11-rc3' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx fixes for v2018.11-rc3 - Fix fit loading address for Zynq
2018-11-07arm: zynq: Setup non zero SPL FIT load addressMichal Simek
Default setup is 0 which is incorrect place because it points to OCM which is allocated for SPL only in our case. Use address in DDR. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-07fs: ubifs: Fix UBIFS decompression on 64 bitPaul Davey
Add local size_t variable to crypto_comp_decompress as intermediate storage for destination length to avoid memory corruption and incorrect results on 64 bit targets. This is what linux does for the various lz compression implementations. Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz> Cc: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
2018-11-06Merge tag 'u-boot-imx-20181106' of git://git.denx.de/u-boot-imxTom Rini
Fix coverity issues for i.MX8
2018-11-06Merge git://git.denx.de/u-boot-marvellTom Rini
2018-11-06Merge git://git.denx.de/u-boot-x86Tom Rini
2018-11-06arm: mvebu: armada-xp-theadorable.dts: Change CS# for 2nd FPGAStefan Roese
The new board version has the 2nd FPGA connected via CS# 0 instead of 2 on SPI bus 1. Change this setup in the DT accordingly. Please note that this change does still work on the old board version because the CS signal is not used on this board. Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-06arm: mvebu: armada-xp-theadorable.dts: Add "spi-flash" compatible propertyStefan Roese
Add the "spi-flash" compatible string so that the generic sf_probe driver can probe the SPI flash on the theadorable Armada-XP board. Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-06arm: mvebu: Move PCI(e) MBUS window to end of RAMStefan Roese
With patch 49b23e035d96 (pci: mvebu: Increase size of PCIe default mapping) the mapping size for each PCI(e) controller was increased from 32MiB to 128MiB. This leads to problems on boards with multiple PCIe slots / ports which are unable to map all PCIe ports, e.g. the Armada-XP theadorable: DRAM: 2 GiB (667 MHz, 64-bit, ECC not enabled) SF: Detected m25p128 with page size 256 Bytes, erase size 256 KiB, total 16 MiB Cannot add window '4:f8', conflicts with another window PCIe unable to add mbus window for mem at f0000000+08000000 Model: Marvell Armada XP theadorable This patch moves the base address for the PCI(e) memory spaces from 0xe8000000 to the end of SDRAM (clipped to a max of 0xc0000000 right now). This gives move room and flexibility for PCI(e) mappings. Signed-off-by: Stefan Roese <sr@denx.de> Cc: VlaoMao <vlaomao@gmail.com> Tested-by: VlaoMao <vlaomao at gmail.com>
2018-11-06MAINTAINERS: add NXP linux team maillist as i.MX reviewerPeng Fan
Add NXP linux team upstream maillist as reviewer Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-11-06ARM: dts: fsl-imx8qxp-mek: Move regulator outside "simple-bus"Fabio Estevam
Commit 3c28576bb0f0 ("arm: dts: imx8qxp: fix build warining") fixed the dts warning by removing the unnecessary #address-cells/#size-cells, but the recommendation for regulators is not to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2018-11-06mx8mq_evk: README: Delete file introduced by mistakeFabio Estevam
board/freescale/mx8mq_evk/README has been introduced by mistake in commit d0dd73974c61 ("imx: add i.MX8QXP MEK board support") Remove it for now as this should be introduced when mx8mq_evk support is in place. Reported-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2018-11-06tools: imx8image: flatten container header only when creating containerPeng Fan
If there is no CONTAINER entry, there is no need to flatten container header. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-11-06tools: imx8image: fix coverity CID 184233Peng Fan
Fix: CID 184233: (NEGATIVE_RETURNS) Using variable "container" as an index to array "imx_header.fhdr". Reported-by: Coverity Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-11-06tools: imx8image: fix coverity CID 184234Peng Fan
Fix: CID 184234: (TAINTED_SCALAR) Using tainted variable "header.num_images - 1" as an index into an array "header.img". Reported-by: Coverity Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-11-06tools: imx8image: check lseek return valuePeng Fan
Check lseek return value. Fix Coverity CID: 184236 184235 184232 Reported-by: Coverity Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2018-11-06x86: acpi: Remove redundant Offset (0x00)Andy Shevchenko
New ACPI assembler issues a warning: board/intel/edison/dsdt.asl.tmp 13: Offset (0x00), Remark 2158 - ^ Unnecessary/redundant use of Offset operator Indeed, in the OperationRegion the offset is 0x00 by default. Thus, drop unneeded Offset() use as suggested by ACPI assembler. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-07 19:32:19 +0000