summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-06-24net: add Faraday FTMAC110 10/100Mbps ethernet supportKuo-Jung Su
Faraday FTMAC110 10/100Mbps supports half-word data transfer for Linux. However it has a weird DMA alignment issue: (1) Tx DMA Buffer Address: 1 bytes aligned: Invalid 2 bytes aligned: O.K 4 bytes aligned: O.K (2) Rx DMA Buffer Address: 1 bytes aligned: Invalid 2 bytes aligned: O.K 4 bytes aligned: Invalid!!! Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Tom Rini <trini@ti.com>
2013-06-24net: phy: supplement support for Micrel's KSZ9031SARTRE Leo
Add function ksz9031_phy_extended_write and ksz9031_phy_extended_read Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
2013-06-24net: macb: add support for gigabit MACBo Shen
Add gigabit MAC support in macb driver - using IP version to distinguish whether MAC is GMAC Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-06-24net: macb: using phylib to configure phy deviceBo Shen
using phylib to configure phy device in macb driver Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-06-24net: macb: using AT91FAMILY replace #ifdeferryBo Shen
Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-06-24ARM: at91sam9n12: add network support with ksz8851_16mllBo Shen
add network support with ksz8851_16mll on at91sam9n12ek board Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-06-24net: ks8851_mll: add ethernet supportRoberto Cerati
The device interface is 16 bits wide. All the available packets are read from the incoming fifo. Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it> Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> [voice.shen@atmel.com: address comments from review results] [voice.shen@atmel.com: clean up for submit] Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
2013-06-24phylib: Add Atheros AR8035 GETH PHY supportXie Xiaobo
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
2013-06-24add support for Xilinx 1000BASE-X phy (GTX)Charles Coldwell
commit 39695029bc15041c809df3db4ba19bd729c447fa Author: Charles Coldwell <coldwell@ll.mit.edu> Date: Tue Feb 19 08:27:33 2013 -0500 Changes to support the Xilinx 1000BASE-X phy (GTX/MGT) Signed-off-by: Charles Coldwell <coldwell@ll.mit.edu>
2013-06-24net: Correct check for link-local target IP conflictJoe Hershberger
Make the link-local code conform more completely with the RFC. This will prevent ARP queries for the target (such as while it is rebooting) from causing the device to choose a different link-local address, thinking that its address is in use by another machine. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-06-24PHY: micrel.c: add support for KSZ9031David Andrey
Add support for Micrel PHY KSZ9031 in phylib, including small rework for KSZ9021 to avoid code duplication Signed-off-by: David Andrey <david.andrey@netmodule.com> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Joe Herschberger <joe.hershberger@gmail.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: Stefan Roese <sr@denx.de>
2013-06-24net/tftp: sparse fixesKim Phillips
tftp.c:464:17: warning: cast to restricted __be16 tftp.c:552:29: warning: cast to restricted __be16 tftp.c:640:33: warning: cast to restricted __be16 tftp.c:642:25: warning: cast to restricted __be16 Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Joe Hershberger <joe.hershberger@gmail.com>
2013-06-24net: make IPaddr type big endianKim Phillips
for use with sparse. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Joe Hershberger <joe.hershberger@gmail.com>
2013-06-24net: Fix build regression in macb.cJoe Hershberger
The added weak symbol must not be static. This was introduced in 416ce623fbad51af57660346ebb6f7befb88b3c9 Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-06-24net/macb: Add arch specific routine to get mdio controlShiraz Hashim
SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their respective phys. Currently there is a fixed configuration in which only a particular MAC can use the MDIO lines. Call an arch specific function to take control of specific mdio lines at runtime. Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Stefan Roese <sr@denx.de>
2013-06-24net/designware: Do not select MIIPORT for RGMII interfaceVipin Kumar
Do not select MIIPORT for RGMII interface Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Stefan Roese <sr@denx.de>
2013-06-24net: nfs: add dynamic wait periodMatthias Brugger
This patch tackles the time out problem which leads to break the boot process, when loading file over nfs. The patch does two things. First of all, we just ignore messages that arrive with a rpc_id smaller then the client id. We just interpret this messages as answers to formaly timed out messages. Second, when a time out occurs we double the time to wait, so that we do not stress the server resending the last message. Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2013-06-24NET: mvgbe: add support for DoveSebastian Hesselbarth
Marvell Dove also uses mvgbe as ethernet driver, therefore add support for Dove to reuse the current driver. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
2013-06-24NET: mvgbe: add phylib supportSebastian Hesselbarth
This add phylib support to the Marvell GBE driver. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
2013-06-24NET: phy: add 88E1310 PHY initializationSebastian Hesselbarth
This adds PHY initialization for Marvell Alaska 88E1310 PHY. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
2013-06-24pxe: add ipappend supportRob Herring
Add ipappend support to pass network device information to the kernel. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24net: Fix build regression in cmd_pxe.cJoe Hershberger
Not all boards define an SOC. As a result, we can't depend on that. This was introduced in 39f985536d3f0df5dba32c15b64ba2b5d32dd296 Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2013-06-24pxe: add support for per arch and SoC default pathsRob Herring
A pxelinux server setup for "default" menu is typically an x86 binary. This does not work well with a mixed architecture setup. Extend the default search to look for default-<arch>-<soc> and then default-<arch> before falling back to just "default". Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: add support for ontimeout tokenRob Herring
ontimeout is similar to default, but is the selection on menu timeout. This is how cobbler sets a default. The label default is supposed to be the default selection when <enter> is pressed. If both default and ontimeout are set, last one parsed wins. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: simplify menu display and selectionRob Herring
Menus with lots of entries and long append lines are hard to read. Just show a numbered list using the label or name and make the choice by entering the number. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: always display a menu when presentRob Herring
The prompt flag is for displaying a "boot:" prompt in pxelinux. This doesn't make sense for u-boot as we don't support the pxelinux command interface. So we should just ignore prompt statements and always show the menu if a menu is present. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: try bootz if bootm fails to find a valid imageRob Herring
Standard pxelinux servers will typically use a zImage rather than u-boot image format, so fallback to bootz if bootm fails. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24bootz: un-staticize do_bootzRob Herring
Make do_bootz available for other functions like do_bootm is. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: fix handling of different localboot valuesRob Herring
Add support for value of -1 For localboot. A value of -1 means return to u-boot prompt. The localboot value is often 0, so we need to distinguish the value from localboot being selected. A value of greater than or equal to 0 means attempt local boot command. If localboot is selected, we don't want to try other entries. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: make string parameters constRob Herring
Convert a bunch of string parameters to be const. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24pxe: Use ethact setting for pxeRob Herring
Get the MAC address using eth_getenv_enetaddr_by_index so that the MAC address of ethact is used. This enables using the a NIC other than the first one for PXE boot. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-06-24net: add ICPlus PHY driverYegor Yefremov
The driver code was taken from Linux kernel source: drivers/net/phy/icplus.c Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2013-06-24phy: export genphy_parse_link()Yegor Yefremov
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2013-06-24net: Add sunxi (Allwinner) wemac driverHenrik Nordström
This patch adds support for the WEMAC, the ethernet controller included in the Allwinner A10 SoC. It will get used in the upcoming A10 board support. From: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
2013-06-24checkpatch: add ignore for network block comment style checkingBo Shen
When use checkpatch.pl to check network related patch, it will report --->8--- WARNING: networking block comments don't use an empty /* line, use /* Comment... ---<8--- So, add --ignore NETWORKING_BLOCK_COMMENT_STYLE into .checkpatch.conf This will help to keep all driver include network related driver use the same comment style Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-06-22Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-06-21arm: optimize relocate_code routineAlbert ARIBAUD
Use section symbols directly Drop support for R_ARM_ABS32 record types Eliminate unneeded intermediate registers Optimize relocation table iteration Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21arm: make __rel_dyn_{start, end} compiler-generatedAlbert ARIBAUD
This change is only done where needed: some linker scripts may contain relocation symbols yet remain unchanged. __rel_dyn_start and __rel_dyn_end each requires its own output section; putting them in relocation sections changes their flags and breaks relocation. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21arm: make __image_copy_{start, end} compiler-generatedAlbert ARIBAUD
This change is only done where needed: some linker scripts may contain __image_copy_{start,end} yet remain unchanged. Also, __image_copy_end needs its own section; putting it in relocation sections changes their flags and makes relocation break. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21arm: generalize lib/bss.c into lib/sections.cAlbert ARIBAUD
File arch/arm/lib/bss.c was initially defined for BSS only, but is now going to also contain definitions for other section-boundary-related symbols, so rename it for better accuracy. Also, remove useless 'used' attributes. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21remove all references to .dynsymAlbert ARIBAUD
Discard all .dynsym sections from linker scripts Remove all __dynsym_start definitions from linker scripts Remove all __dynsym_start references from the codebase Note: this touches include/asm-generic/sections.h, which is not ARM-specific, but actual uses of __dynsym_start are only in ARM, so this patch can safely go through the ARM repository. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21arm: ensure u-boot only uses relative relocationsAlbert ARIBAUD
Add a Makefile target ('checkarmreloc') which fails if the ELF binary contains relocation records of types other than R_ARM_RELATIVE. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-20powerpc/85xx: Add P1023RDB board supportChunhe Lan
P1023RDB Specification: ----------------------- Memory subsystem: 512MB DDR3 (Fixed DDR on board) 64MB NOR flash 128MB NAND flash Ethernet: eTSEC1: Connected to Atheros AR8035 GETH PHY eTSEC2: Connected to Atheros AR8035 GETH PHY PCIe: Three mini-PCIe slots USB: Two USB2.0 Type A ports I2C: AT24C08 8K Board EEPROM (8 bit address) Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20powerpc/mpc85xx:Disable Debug TLB entry before init_tlbsPrabhakar Kushwaha
init_tlbs() initialize all the TLB entries required for the system. So disable DEBUG TLB entry before TLB entries initialization. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20powerpc/pixis: Fix pixis help messageYork Sun
"pixis_reset help" command prints the message without a new line "\n", which makes the prompt on the same line. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20powerpc/CoreNet: Allow pbl images to take u-boot images != 512KChris Packham
Instead of assuming that SYS_TEXT_BASE is 0xFFF80000 calculate the initial pbl command offset by subtracting the image size from the top of the 24-bit address range. Also increase the size of the memory buffer to accommodate a larger output image. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20powerpc: mpc85xx/mpc86xx: Fix off-by-one boundary checking with ARRAY_SIZEAxel Lin
If a variable is used as array subscript, it's valid value range is 0 ... ARRAY_SIZE -1. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20Makefile: move the common makefile line to public areaYing Zhang
Move the common makefile line shared by the SPL and non-SPL to the public area, so that we can avoid excessive SPL symbols. Some of them will be used by the SPL later. This patch is on top of the patch "common/Makefile: Add new symbol CONFIG_SPL_ENV_SUPPORT for environment in SPL". Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20common/Makefile: Add new symbol CONFIG_SPL_ENV_SUPPORT for environment in SPLYing Zhang
There will need the environment in SPL for reasons other than network support (in particular, hwconfig contains info for how to set up DDR). Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT for environment in common/Makefile. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20powerpc/mpc85xx: modify the functionality clear_bss and aligning the end ↵Ying Zhang
address of the BSS There will clear the BSS in the function clear_bss(), the reset address of the BSS started from the __bss_start, and increased by four-byte increments, finally stoped depending on the address is equal to the _bss_end. If the end address __bss_end is not alignment to 4byte, it will be an infinite loop. 1. The reset action stoped depending on the reset address is greater than or equal the end address of the BSS. 2. The end address of the BSS should be 4byte aligned. Because the reset unit is 4 Bytes. This patch is on top of the patch "powerpc/mpc85xx: support application without resetvec segment in the linker script". Signed-off-by: Ying Zhang <b40530@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-23 02:31:56 +0000