summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-03-04Merge tag 'u-boot-atmel-2019.04-a' of git://git.denx.de/u-boot-atmelTom Rini
First set of u-boot-atmel fixes for 2019.04 cycle
2019-03-04Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
- Enable DHCP as boot-source in distro boot for NXP layerscape platforms - fix register layout for SEC on Layerscape architectures - fixes related to DPAA2 ethernet
2019-03-04configs: at91: remove SPL_GENERATE_ATMEL_PMECC_HEADER from non-nand configsEugen Hristev
SPL_GENERATE_ATMEL_PMECC_HEADER will generate a header for the SPL for NAND information. The initial stage 1 bootloader will use this header in case the NAND flash doesn't support commands to retrieve sector size, etc. However this header is bad for different boot media, like MMC or SPI. In case SD_BOOT or SPI_BOOT is used, remove the config for this. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-03-04configs: sama5d27_som1_ek: Activate misc init for uSD variantAlexander Dahl
This was already set for 'sama5d27_som1_ek_mmc_defconfig' (first SD card, full size). Without this option set, the MAC address is not read from the I²C EEPROM at boot, and remains unset: U-Boot 2019.01 (Jan 01 2019 - 00:00:00 +0000) CPU: SAMA5D27 1G bits DDR2 SDRAM Crystal frequency: 24 MHz CPU clock : 492 MHz Master clock : 164 MHz DRAM: 128 MiB MMC: sdio-host@a0000000: 0, sdio-host@b0000000: 1 Loading Environment from FAT... OK In: serial Out: serial Err: serial Net: Error: ethernet@f8008000 address not set. eth-1: ethernet@f8008000 Hit any key to stop autoboot: 0 Signed-off-by: Alexander Dahl <ada@thorsis.com>
2019-03-03board: Enable DHCP distro boot for LS1012a, LS1021aYunfeng Ding
Enable DHCP distro boot for Layerscape LS1012A and LS1021A. Signed-off-by: Yunfeng Ding <yunfeng.ding@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03armv8: fsl-layerscape: avoid DT fixup warningLaurentiu Tudor
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node from the device tree. This causes this warning to be issued when doing the device tree fixup: WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND. Fix it by excluding the device tree fixup for the JR reserved by sec_firmware. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03armv8: fsl-layerscape: fix SEC QI ICID setupLaurentiu Tudor
The SEC QI ICID setup in the QIIC_LS register is actually an offset that is being added to the ICID coming from the qman portal. Setting it with a non-zero value breaks SMMU setup as the resulting ICID is not known. On top of that, the SEC QI ICID must match the qman portal ICIDs in order to share the isolation context. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03fsl_sec: fix register layout on Layerscape architecturesLaurentiu Tudor
On Layerscape architectures the SEC memory map is 1MB and the register blocks contained in it are 64KB aligned, not 4KB as the ccsr_sec structure currently assumes. Fix the layout of the structure for these architectures. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1046qds: Enable PPA for secure bootPrabhakar Kushwaha
Re-organize defconfig and enabled PPA for secure boot Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03configs: fsl: move DDR specific defines to KconfigRajesh Bhagat
Moves below DDR specific defines to Kconfig: CONFIG_FSL_DDR_BIST CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE CONFIG_FSL_DDR_INTERACTIVE CONFIG_FSL_DDR_SYNC_REFRESH Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1043a: use default scan_dev_for_bootMian Yousaf Kaukab
Default environment variable is more complete. Also scans for efi binaries for example. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1043a: enable dhcp bootMian Yousaf Kaukab
dhcp boot is a useful feature and works out-of-the-box on these platforms. Enable it as a boot source. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1043a: enable EFI_LOADER_BOUNCE_BUFFERMian Yousaf Kaukab
EFI applications need bounce buffers to work properly on these platforms. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1046a: use default scan_dev_for_bootMian Yousaf Kaukab
Default environment variable is more complete. Also scans for efi binaries for example. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1046a: enable dhcp bootMian Yousaf Kaukab
dhcp boot is a useful feature and works out-of-the-box on these platforms. Enable it as a boot source. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1046a: enable EFI_LOADER_BOUNCE_BUFFERMian Yousaf Kaukab
EFI applications need bounce buffers to work properly on these platforms. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls2080ardb: use default scan_dev_for_bootMian Yousaf Kaukab
Default environment variable is more complete. Also scans for efi binaries for example. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03Revert "ls2080ardb: remove dhcp function from env as boot source"Mian Yousaf Kaukab
dhcp boot is a useful feature and works out-of-the-box for ls2088a platforms. Moreover, no solid reason is given for disabling it. Revert the patch to re-enable it. This reverts commit aea5cd75e63c20de4c00ce24a93eeee8542f923e. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1088ardb: use default scan_dev_for_bootMian Yousaf Kaukab
Default environment variable is more complete. Also scans for efi binaries for example. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03Revert "ls1088a: remove dhcp function from u-boot env as boot source"Mian Yousaf Kaukab
dhcp boot is a useful feature and works out-of-the-box for ls1088a platforms. Moreover, no solid reason is given for disabling it. Revert the patch to re-enable it. This reverts commit 863e42e8b1f9e97d87919e20e34a7b98089f7522. Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1088a: fix fsl-mc search pathMian Yousaf Kaukab
Path for fsl-mc node in kernel device-tree is /soc/fsl-mc whereas in u-boot it is /fsl-mc. Fix the incorrect search path to fix following error: fdt_fixup_board_enet: ERROR: fsl-mc node not found in device tree (error -1) Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1088a: fix dppa exit when using efi bootMian Yousaf Kaukab
Same issue for ls2080a was fixed by following patch: b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03Merge git://git.denx.de/u-boot-mpc85xxTom Rini
2019-03-02powerpc: t104xrdb: Add support of MTA9ADF1G72AZ DDRPeng Ma
T1040RDB has been upgraded to support new DDR ie. MTA9ADF1G72AZ-3G2, 8GB. So adding support of new DDR part by updating board_specific_parameters udimm0. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-02powerpc: enabled building with CONFIG_DM=yHeinrich Schuchardt
Moving to the driver model requires CONFIG_DM to be enabled. Currently several boards like kmeter1_defconfig produce a build error when CONFIG_DM is enabled: In file included from include/common.h:35, from ./arch/powerpc/include/asm/fsl_lbc.h:10, from include/mpc83xx.h:10, from ./arch/powerpc/include/asm/ppc.h:27, from ./arch/powerpc/include/asm/u-boot.h:18, from include/dm/of.h:10, from include/dm/ofnode.h:12, from include/dm/device.h:13, from include/linux/mtd/mtd.h:26, from drivers/mtd/mtdconcat.c:25: include/image.h: In function ‘image_check_target_arch’: include/image.h:846:3: error: #error "please define IH_ARCH_DEFAULT in your arch asm/u-boot.h" # error "please define IH_ARCH_DEFAULT in your arch asm/u-boot.h" ^~~~~ include/image.h:848:31: error: ‘IH_ARCH_DEFAULT’ undeclared (first use in this function); did you mean ‘IH_ARCH_COUNT’? return image_check_arch(hdr, IH_ARCH_DEFAULT); The error can be avoided by moving the definition of IH_ARCH_DEFAULT before #include <asm/ppc.h> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-28Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- SoCFPGA cache/gpio fixes
2019-02-28Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Gen2/Gen3 fixes for warnings and sdhi
2019-02-28Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- Various Bananapi fixes
2019-02-28Merge branch '2019-02-29-master-imports'Tom Rini
- Assorted BSP fixes - Kbuild fix
2019-02-28spl: add debug print for early malloc usageSimon Goldschmidt
To find out how big the early malloc heap must be in SPL, add a debug print statement that dumps its usage before switching to relocated heap in spl_relocate_stack_gd() via CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-02-28kbuild: fix DTB .cmd source variableStephen Warren
*.dts are processed using a custom command, then the C pre-processor is run on them, then they are compiled using dtc. Thus, the dependency files generated by both cpp and dtc reference a temporary file name rather than the actual source file. While this information isn't used for any purpose by the build system, and hence this causes no functional issue, it does cause the dependency files to contain invalid and confusing data, which is unhelpful while debugging build problems. Fix this using sed. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-28kbuild: make arch-dtbs target PHONYStephen Warren
Without this, the arch-dtbs target only gets evaluated when building U-Boot the first time, not when re-building (incrementally building) U-Boot. Thus incremental builds ignore changes to DTB files. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-28doc: binding: rename directory ram to memory-controllerPatrick Delaunay
Alignment with kernel directory name as it have already bindings for DDR controllers in the directory: Documentation/devicetree/bindings/memory-controller PS: the drivers using RAM u-class should be associated with this binding directory Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-28fs: fat: fix link error when building with DEBUG=1Heinrich Schuchardt
When compiling with DEBUG=1 an error fs/fat/fat_write.c:831: undefined reference to `__aeabi_ldivmod' occurred. We should use do_div() instead of the modulus operator. filesize and cur_pos cannot be negative. So let's use u64 to avoid warnings. Fixes: cb8af8af5ba0 ("fs: fat: support write with non-zero offset") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-02-28arm: pdu001: Fix order of include filesFelix Brack
Fix the order of include files according to U-Boot coding style. Signed-off-by: Felix Brack <fb@ltec.ch>
2019-02-28.gitignore: Ignore regenerated *.dtbo filesMichal Simek
*.dtbo are dt overlays files which should be also ignored as *.dtb. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-28ARM: cache: Fix incorrect bitwise operationMarek Vasut
The loop implemented in the code is supposed to check whether the PL310 operation register has any bit from the mask set. Currently, the code checks whether the PL310 operation register has any bit set AND whether the mask is non-zero, which is incorrect. Fix the conditional. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Tom Rini <trini@konsulko.com> Fixes: 93bc21930a1b ("armv7: add PL310 support to u-boot") Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2019-02-28spi: omap3: fix set_wordlen() reading from incorrect address for CHCONFDavid Rivshin
_omap3_spi_set_wordlen() indexed the regs->channel[] array with the old wordlen (instead of the chipselect number) when reading the current CHCONF register value. This meant it read from the wrong memory location, modified that value, and then wrote it back to the correct CHCONF register. The end result is that most slave configuration settings would be lost, such as clock divisor, clock/chipselect polarities, etc. Fixes: 77b8d04854f4 ("spi: omap3: Convert to driver model") Signed-off-by: David Rivshin <drivshin@allworx.com>
2019-02-27Merge git://git.denx.de/u-boot-riscvTom Rini
- SiFive FU540 Support
2019-02-27riscv: Enable CONFIG_SYS_BOOT_RAMDISK_HIGH for using initrdAnup Patel
This patch enables CONFIG_SYS_BOOT_RAMDISK_HIGH for RISC-V because bootm will update initrd location in DTB only if CONFIG_SYS_BOOT_RAMDISK_HIGH is enabled. If we don't enable this option then bootm assumes DTB already has initrd details which is not the case most of the time. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-02-27doc: Add a readme guide for SiFive FU540Atish Patra
The readme guide describes the procedure to build, flash and boot Linux using U-Boot on HiFive Unleashed. It also explains the current state of U-boot support and future action items. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-02-27riscv: Add SiFive FU540 board supportAnup Patel
This patch adds SiFive FU540 board support. For now, only SiFive serial, SiFive PRCI, and Cadance MACB drivers are only enabled. The SiFive FU540 defconfig by default builds U-Boot for S-Mode because U-Boot on SiFive FU540 will run in S-Mode as payload of BBL or OpenSBI. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-02-27cpu: Bind timer driver for boot hartAtish Patra
Currently, timer driver is bound only for hart0. There is no mandatory requirement that hart0 should always come up. In fact, HiFive Unleashed SoC hart0 doesn't boot in S-mode because it only has M-mode. The timer driver should be bound for boot hart. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-02-27drivers: serial_sifive: Skip baudrate config if no input clockAtish Patra
It is possible that input clock is not available because clk device was not available and 'clock-frequency' DT property is also not available. In this case, instead of failing we should just skip baudrate config by returning zero. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2019-02-27drivers: serial_sifive: Fix baud rate calculationAtish Patra
Compute the baud rate multipler with more precision. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-02-27clk: Add fixed-factor clock driverAnup Patel
This patch adds fixed-factor clock driver which derives clock rate by dividing (div) and multiplying (mult) fixed factors to a parent clock. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-02-27clk: Add SiFive FU540 PRCI clock driverAnup Patel
Add driver code for the SiFive FU540 PRCI IP block. This IP block handles reset and clock control for the SiFive FU540 device and implements SoC-level clock tree controls and dividers. Based on code written by Wesley Terpstra <wesley@sifive.com> found in commit 999529edf517ed75b56659d456d221b2ee56bb60 of: https://github.com/riscv/riscv-linux Boot and PLL rate change were tested on a SiFive HiFive Unleashed board. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2019-02-27net: macb: Fix GEM hardware detectionAtish Patra
Fix MID bit field check to correctly identify all GEM hardwares. The check is updated as per macb driver in Linux location: <linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259 Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-02-27net: macb: Fix clk API usage for RISC-V systemsAnup Patel
Don't fail in macb_enable_clk() if clk_enable() returns -ENOSYS because we get -ENOSYS for fixed-rate clocks. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-02-27riscv: generic: Ensure that U-Boot runs within 4GB for 64bit systemsAnup Patel
On 64bit systems, the DRAM top can be easily beyond 4GB and U-Boot DMA mapping APIs will generate DMA addresses beyond 4GB. This breaks DMA programming in 32bit DMA capable devices (such as Cadence MACB ethernet). For example, If DRAM is more then 2GB on QEMU sifive_u machine then Cadence MACB ethernet stops working for U-Boot because it is a 32bit DMA capable device. To handle 32bit DMA capable devices on 64bit systems, we provide custom implementation of board_get_usable_ram_top() which ensures that usable ram top is not more then 4GB. This in-turn ensures that U-Boot always runs within 4GB hence DMA addresses generated by DMA mapping APIs will be within 4GB too. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-26 22:22:46 +0000