summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-08ARM: dts: at91: sam9x60ek: add onewire supportEugen Hristev
Add support for onewire memory. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: dts: at91: sam9x60: add onewire nodeEugen Hristev
Add onewire node for w1 support. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08configs: Add sam9x60ek_qspiflash_defconfigTudor Ambarus
Boot from QSPI nor flash. The at91bootstrap, u-boot, u-boot env redundant, u-boot env, device tree and kernel will reside in the QSPI nor flash. The rootfs will reside in the NAND flash. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08ARM: dts: at91: sam9x60ek: Enable qspi nodeTudor Ambarus
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register access, the other for the qspi core and phy. Both are mandatory. Enable the qspi node together with the SST26VF064B qspi nor flash memory. Booting from the QSPI NOR flash is now possible. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08configs: sam9x60ek: Add QSPI_BOOT definesTudor Ambarus
Cope with the offsets defined at: https://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections/demo_nandflash_map_lnx4sam6x.png The environment starts at 0x140000 and it's of size 0x20000. The device tree starts at 0x180000 and it's of size 0x80000. The zImage starts at 0x200000 and it's of size 0x600000. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08configs: Add sam9x60ek_nandflash_defconfigTudor Ambarus
Boot from nand flash. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08board: sam9x60ek: Add NAND flash supportTudor Ambarus
- EBI Chip Select Register is now in SFR, - the pins are set to default values, - timings are matching MT29F4G08BABWP's nand flash requirements. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08ARM: at91: Add SFR definitionsTudor Ambarus
sama5's SFR has at offset 0x04 the DDR Configuration Register, while sam9x60's SFR contains the EBI Chip Select Register. Add a union to reconcile both boards. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08ARM: at91: Rename sama5_sfr.h to at91_sfr.hTudor Ambarus
The Special Function Registers (SFR) are present in sam9x5 and sam9x60 too, rename sama5_sfr to at91_sfr.h. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08configs: Add sam9x60ek_mmc_defconfigSandeep Sheriker Mallikarjun
add sam9x60ek_mmc_defconfig and for now only supports booting from sdcard. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [nicolas.ferre@microchip.com: split patch, add Ethernet controller, phy and tools] [claudiu.beznea@microchip.com: add CONFIG_OF_LIBFDT_OVERLAY] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> [tudor.ambarus@microchip.com: Fix number of DRAM banks: One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks] Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08board: atmel: Add sam9x60ek boardSandeep Sheriker Mallikarjun
Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> [tudor.ambarus@microchip.com: - fix number of DRAM banks: One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks] - drop SPL related macros - drop memtest macros - drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros - drop inclusion of asm/arch/at91sam9_smc.h] Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08ARM: dts: at91: sam9x60: Add macb0 Ethernet controllerNicolas Ferre
Add Ethernet controller to dtsi file and enable it on sam9x60ek platform connected with rmii. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
2019-10-08ARM: dts: Add dts files for sam9x60ekSandeep Sheriker Mallikarjun
add device tree files for sam9x60ek board with below changes. - Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit) - Add the reg property for the pinctrl node. - Add the "u-boot,dm-pre-reloc" property to determine which nodes are used by the board_init_f stage. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> [prasanthi.chellakumar@microchip.com: fix style/whitespace issues] Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com> [nicolas.ferre@microchip.com: - fix gclk, - fix pio/pinctrl controller definition and allow to have more than only PIOA for this SoC, - removing pinctrl address] Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [claudiu.beznea@microchip.com: - use SAM9X60's compatible for pinctrl - add drive strength and slew rate options for SDMMC0 pins.] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> [tudor.ambarus@microchip.com: - u-boot,dm-pre-reloc property in dedicated file, - fix pit len, starts from 0xFFFFFE40 and it is of len 0x10] Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08ARM: at91: Add sam9x60 socSandeep Sheriker Mallikarjun
Add new Microchip sam9x60 SoC based on an ARM926. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> [tudor.ambarus@microchip.com: fix SFR definition] Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-10-08mmc: atmel_sdhci: Add sam9x60-sdhci compatibility stringSandeep Sheriker Mallikarjun
Add new compatibility string for matching sam9x60 product. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2019-10-08net: macb: Add sam9x60-macb compatibility stringNicolas Ferre
Add this new compatibility string for matching sam9x60 product macb. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
2019-10-08board: atmel: sama5d27_wlsom1_ek: fix SPL OFFS on SPIEugen Hristev
Fixes redefinition of CONFIG_SYS_SPI_U_BOOT_OFFS This is now a Kconfig Fixes: e40a9ba6d2d5 ("board: atmel: sama5d2_wlsom1_ek: add qspi support and qspi boot config") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08configs: sama5d27_wlsom1_ek: add CONFIG_SPL_AT91_MCK_BYPASSEugen Hristev
This board has an external oscillator as MCK that does not need driving. Bypass the driving for the main oscillator in SPL. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: common: remove year from print messageEugen Hristev
Remove 2017 from being printed at boot video console. This is outdated. To avoid this situation, remove the year completely. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: dts: at91: sama5d27_wlsom1: add hlcdc nodeEugen Hristev
Add node for hlcld for u-boot logo display at boot. This is compatible with the Precision Design Associates (PDA) TM5000 screen. Timings are compatible with simple panel from Linux, panel name is pda_91_00156_a0 Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: sama5d27_wlsom1_ek: start green led in SPLEugen Hristev
When SPL boots, enable green led on the board. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: sama5d2_wlsom1_ek: add qspi support and qspi boot configEugen Hristev
Add support for qspi memory on board. Created boot support for QSPI for both u-boot proper and SPL. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: dts: at91: sama5d27_wlsom1_ek: add support for qspiEugen Hristev
Add node for qspi1 memory connected on the wlsom Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: dts: at91: sama5d2: add seq for qspi1Eugen Hristev
qspi1 does not have an alias/seq number. This is required for SPL default SF bus booting for the boards that have this SoC Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: sama5d2_wlsom1_ek: add SPL supportEugen Hristev
Add support for SPL for this board: DRAM initialization, PMC initialization, MMC boot. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: at91: mpddrc: add lpddr2 initialization procedureEugen Hristev
Implement the lpddr2 initialization procedure for at91 mpddrc multi-port ddram controller. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: laird: wb50n: use configure_ddrcfg_input_buffersEugen Hristev
Replace code with new function configure_ddrcfg_input_buffers from SFR mach driver. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: at91: sfr: implement DDR input buffers open functionEugen Hristev
Add a function in SFR implementation that will open the DDR input buffers. This can be called at DRAM initialization time. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: at91: sfr: convert to KconfigEugen Hristev
This converts the at91 sfr to Kconfig Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08board: atmel: add sama5d27_wlsom1_ek boardNicolas Ferre
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> [eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10 Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-08ARM: at91: Add the chip ID for SAMA5D2 LPDDR2 SiPNicolas Ferre
The SAMA5D2 LPDDR2 SiP (System in Package) is added for SoC identification. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
2019-10-07Prepare v2019.10Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-07NET: DW: fix regression for ARC boardsEugeniy Paltsev
The commit 642b80d256e ("net: designware: drop compatible altr, socfpga-stmmac") breaks designware ethernet for all ARC boards. It removes "altr, socfpga-stmmac" compatible from "drivers/net/designware.c" without changing compatible in the boards which use it. Fix that by adding "snps,arc-dwmac-3.70a" compatible string to "drivers/net/designware.c" and using it in ARC boards device tree. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
2019-10-06Merge branch '2019-10-06-master-imports'Tom Rini
- Regression work-around on SoCFPGA by disabling WDT in some cases. - Fix seg fault on 'host info' in some cases.
2019-10-06cmd: host: fix seg fault at "host info"AKASHI Takahiro
With the patch below applied, host_block_dev structure was switched to be placed in platdata rather than priv. The command "host info" must be aligned with this change. Otherwise, we will see "Segmentation Fault." Fixes: 8f994c860d91 ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-06MAINTAINERS: Update my email addressMaxime Ripard
I'm not at bootlin anymore, and my mail address doesn't work any longer. Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-06arm: socfpga: disable CONFIG_SPL_WDT for gen5 and a10Simon Goldschmidt
These boards don't have a watchdog enabled in SPL, so make sure CONFIG_SPL_WDT is not enabled. Fixes: commit 6874cb72204f ("watchdog: Split WDT from SPL_WDT") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-06gitlab-ci: fix typo 'plaforms'Heinrich Schuchardt
%s/plaforms/platforms/g Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-05Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulator
2019-10-04Merge branch '2019-10-04-master-imports'Tom Rini
- Assorted TI platform fixes - Revert the change that broke environment flag validation - Assorted typo fixes - Assorted Kconfig dependency fixes - Other minor bug fixes
2019-10-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- dm: core: Correct low cell in ofnode_read_pci_addr() - dm: core: Correct bad cast in ofnode_get_addr_size_index()
2019-10-04Revert "env: solve compilation error in SPL"Tom Rini
This reverts commit 7d4776545b0f8a8827e5d061206faf61c9ba6ea9. The changes here break environment validation and furthermore do not seem to be required. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-04ARM: dts: imx6q-logicpd: Add missing imx6q-logicpd-u-boot for SPLAdam Ford
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file which will enable these functions so SPL can properly setup UART, detect microSD card, and startup. Fixes: 8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled, remove MMC init") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-10-04initcall.h: initcall_run_list(): Improve debug outputOvidiu Panait
Existing debug output is mixed with the function name: initcall_run_list() initcall: 25263initcall_run_list() (relocated to 425263) Turn it to: initcall_run_list() initcall: 25263 (relocated to 425263) Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
2019-10-04Kconfig: fix a typo in the description of bmp command.Andrius Štikonas
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
2019-10-04Kconfig: Migrate CONFIG_BOOTM_* optionsTom Rini
Migrate all of the existing OS support options that are under CONFIG_BOOTM_* to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-04cmd: part: number: return hexadecimal valueRoman Stratiienko
At this point we are using part number sub-command to retrieve UUID of the partition using it's name. e.g.: part number mmc $mmcdev system_a system_a_index part uuid mmc $mmcdev:${system_a_index} system_a_uuid Since 'part uuid' sub-command expects partition index in hex format and 'part number' returns decimal value, 'part uuid' command will provide wrong UUID or fail. Fixes: be683756f62034 ("cmd: part: Add 'number' sub-command") Cc: Dirk Behme <dirk.behme@de.bosch.com> Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com> Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-10-04ARM: keystone2: update the default addresses of the secure monitorJean-Jacques Hiblot
To accommodate the growth of u-boot, we need to shift the location of the secure monitor. Moving it 64kB further. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-04board: ti: am654: Disable TRNG node for HS devicesAndrew F. Davis
On HS devices the access to TRNG is restricted on the non-secure ARM side, disable the node in DT to prevent firewall violations. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-04autoboot: add necessary dependency at AUTOBOOT_MENU_SHOWAKASHI Takahiro
Otherwise, menu_show() will be undefined in bootdelay_process(). Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
generated by cgit (git 2.34.1) at 2025-01-09 06:43:38 +0000