summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-06-14sh: ms7750se: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14sh: ms7722: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14sh: espt_giga: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14arm: socfpga: provide default SPL_SIZE_LIMIT for gen5Simon Goldschmidt
This provides an SPL_SIZE_LIMIT that makes the build check that the SPL binary loaded from flash fits into the SRAM (64 KiB) and leaves enough room for global data, heap and stack (512 bytes assumed stack usage). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-06-14arm: dts: Stratix10: Enable i2cLey Foon Tan
Enable i2c1 in Stratix 10 devkit. SOCFPGA_STRATIX10 # i2c bus Bus 0: i2c@ffc02900 SOCFPGA_STRATIX10 # i2c dev 0 Setting bus to 0 SOCFPGA_STRATIX10 # i2c probe Valid chip addresses: 14 4C 51 68 74 Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-06-14fastboot: Check if partition really exist in getvar_has_slot()Igor Opaniuk
Currently getvar_has_slot() invocation for "boot" and "system" partitions always returns affirmative response regardless the fact of existence of these partitions, which leads to impossibility to flash them on old non-A/B AOSP setups, where _a/_b suffixes aren't used: $ fastboot flash boot boot.img Sending 'boot__a' (11301 KB) OKAY [ 0.451s] Writing 'boot__a' FAILED (remote: 'cannot find partition') fastboot: error: Command failed Although partition layout is: -> part list mmc 0 Partition Map for MMC device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000107ff "boot" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: ea2e2470-db4a-d646-b828-10167f736d63 2 0x00010800 0x000127ff "environment" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 10a819d2-6004-3d48-bd87-114e2a796db9 3 0x00012800 0x0001a7ff "recovery" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 9ea116e4-8a34-0c48-8cf5-2fe9480f56cd 4 0x0001a800 0x0031a7ff "system" attrs: 0x0000000000000000 ...... This patch adds checks of existence for requested partitions on eMMC/NAND. Fixes: f73a7df984a9 ("net: fastboot: Merge AOSP UDP fastboot") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-06-14fastboot: getvar: Refactor fastboot_*_get_part_info() usageSam Protsenko
Extract fastboot_*_get_part_info() usage for MMC and NAND into getvar_get_part_info() function, as it will be needed further in other functions. This way we can avoid code duplication and mess with preprocessor directives across all points of usage. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-06-14fastboot: Use const qualifier for char *part_nameSam Protsenko
In fastboot_*_get_part_info() functions we can use stronger typing by expecting const strings. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-06-14fastboot: Fix slot names reported by getvarSam Protsenko
In commit [1] fastboot tool was changed w.r.t. new A/B specification [2], and now we should report slot names in "a" format instead of "_a". Latter is now considered legacy and we shouldn't rely on that anymore. Due to this one can observe next error with recent fastboot tool: $ fastboot flash boot boot.img Sending 'boot__a' (11301 KB) OKAY [ 0.451s] Writing 'boot__a' FAILED (remote: 'cannot find partition') fastboot: error: Command failed Let's use new slot format in order to fix double underscores "__" and to be in sync with AOSP master. [1] https://android.googlesource.com/platform/system/core/+/8091947847d5e5130b09d2ac0a4bdc900f3b77c5 [2] https://source.android.com/devices/tech/ota/ab/ab_implement#partitions Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-06-14usb: gadget: error out if g_dnl registration failsSjoerd Simons
If g_dnl_register fails return an error rather then stubornly continuing onwards. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2019-06-14spl: dfu: Fix printed variable nameMarek Vasut
The SPL DFU uses dfu_alt_info_N variable name to determine the DFU configuration, where N is the name of the media (e.g. ram). It does not use the plain dfu_alt_info. Print the name of the missing env variable in case of a failure instead of printing dfu_alt_info, which is just the name of the parameter passed to spl_dfu_cmd(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
2019-06-13configs: Disable now unbuildable SPI options for boardsTom Rini
Now that various SPI related options depend on CONFIG_DEPRECATED, in order for platforms to build out of the box they need to disable various other options. Cc: Albert ARIBAUD <albert.aribaud@3adev.fr> Cc: Marek Vasut <marex@denx.de> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13spi: Kconfig: Mark LPC32XX_SSP as DEPRECATEDJagan Teki
Mark LPC32XX_SSP as DEPRECATED, this so the resulting build shows warning for deprecated configuration enabled and associated code will remove in v2019.07 release. Cc: Albert ARIBAUD <albert.aribaud@3adev.fr> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Sylvain Lemieux <slemieux@tycoint.com> [trini: Switch to DEPRECATED] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-13spi: Kconfig: Mark SOFT_SPI as DEPRECATEDJagan Teki
Mark SOFT_SPI as DEPRECATED, this so the resulting build shows warning for deprecated configuration enabled and associated code will remove in v2019.07 release. Cc: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [trini: Switch to DEPRECATED] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-13spi: Kconfig: Mark SH_SPI as DEPRECATEDJagan Teki
Mark SH_SPI as DEPRECATED, this so the resulting build shows warning for a deprecated configuration enabled and associated code will remove in v2019.07 release. Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [trini: Switch to DEPRECATED] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-13spi: Kconfig: Mark MXS_SPI has DEPRECATEDJagan Teki
Mark MXS_SPI as DEPRECATED, this so the resulting build shows warning for broken configuration enabled and associated code will remove in v2019.07 release. Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [trini: Switch to DEPRECATED] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-13Makefile: Trigger a warning for legcay spi driversJagan Teki
We have a warning text for non dm converted spi drivers, but the plan is to mark all these respective drivers with CONFIG_DEPRECATED. So, trigger a warning saying that these driver configurations and associated code will remove in v2019.07 (earlier plan is to remove it from v2019.04) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13Makefile: Trigger a Warning if DEPRECATED is definedJagan Teki
If configured target has deprecated configs enabled, trigger a warning about this. Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [trini: Change from BROKEN to DEPRECATED] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-13Kconfig: Add DEPRECATED optionTom Rini
Add a new option, CONFIG_DEPRECATED, for code that relies on deprecated functionality and has not been converted past the deadline for conversion. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13Kconfig: Add SPI / SPI_FLASH as dependenciesTom Rini
In order to use CMD_SF / CMD_SPI / ENV_IS_IN_SPI_FLASH we need to have the SPI (or SPI_FLASH/DM_SPI_FLASH, for CMD_SF) enabled. Express this in the Kconfigs. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13arm: Remove zipitz2 boardTom Rini
Per discussion on the list, drop this board again. Cc: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-12Merge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogicTom Rini
- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups - pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB - pinctrl: meson: add support for getting pinmux status - pinctrl: meson-g12a: add support for drive-strength-microamp property
2019-06-12Merge tag 'efi-2019-07-rc5' of git://git.denx.de/u-boot-efiTom Rini
Pull request for UEFI sub-system for v2019.07-rc5 This pull request provides fixes for event services.
2019-06-12ARM: bcm283x: Fix definition of MBOX_TAG_TEST_PIXEL_ORDERBerkus Decker
The MBOX_TAG_TEST_PIXEL_ORDER define is incorrect. According to official documentation it has a slightly different numbering. Correct mailbox constants are defined in e.g. linux raspberry-firmware https://code.woboq.org/linux/linux/include/soc/bcm2835/raspberrypi-firmware.h.html#RPI_FIRMWARE_FRAMEBUFFER_TEST_PIXEL_ORDER These are obtained from the bcm2835 documentation e.g. https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface#test-pixel-order Fix the define to get us back in sync with the spec. Signed-off-by: Berkus Decker <berkus+github@metta.systems> [agraf: clarify subject, extend commit message] Signed-off-by: Alexander Graf <agraf@csgraf.de> [mb: updating email of agraf] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-06-12ARM: defconfig: add Raspberry Pi 3 Model B+Heinrich Schuchardt
Provide a defconfig file for the Raspberry Pi 3 Model B+. It is based on the Raspberry Pi 3 file, just changing the device tree. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-06-12fdt: update bcm283x device tree sources to Linux 5.1-rc6 stateHeinrich Schuchardt
Updating the bcm283x device tree sources adds the device trees for - Raspberry Pi 3 Model A+ - Raspberry Pi 3 Model B+ - Raspberry Pi Compute Module IO board rev1 - Raspberry Pi Compute Module 3 IO board V3.0 - Raspberry Pi Zero Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-06-12Fix compilation error if CONFIG_USB is disabledakaher
This patch is to fix the following compilation error when disabling CONFIG_USB for Rpi3: include/config_distro_bootcmd.h:242:2: error: expected ‘}’ before ‘BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB’ BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB Signed-off-by: Ajay Kaher <akaher@vmware.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-06-12pinctrl: meson-gxbb: add hdmi related pinsMaxime Jourdan
The GXBB pinctrl is missing pins related to HDMI, namely hot plug detection (hpd) and I2C (sda + scl). This fixes HDMI support for GXBB in u-boot. Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12pinctrl: meson: g12a: add DS bank valueGuillaume La Roque
add drive-strength bank regiter and bit value for G12A SoC Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12pinctrl: meson: add support of drive-strength-microampGuillaume La Roque
drive-strength-microamp is a new feature needed for G12A SoC. the default DS setting after boot is usually 500uA and it is not enough for many functions. We need to be able to set the drive strength to reliably enable things like MMC, I2C, etc ... Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12dm: pinctrl: Add driver-strength-microamp propertyGuillaume La Roque
Add drive-strength-microamp property support to allow drive strength in uA Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12pinctrl: meson-axg: add support for getting pinmux statusNeil Armstrong
In order to support the "pinmux status" command, use the common functions to get the pins count and names, and add the AXG specific function to get the current function from registers. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12pinctrl: meson-gx: add support for getting pinmux statusNeil Armstrong
In order to support the "pinmux status" command, use the common functions to get the pins count and names, and add the GX specific function to get the current function from registers. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
2019-06-12pinctrl: meson: add common function to get pins nameNeil Armstrong
In order to support the "pinmux status" command, add common function to get pins count and pin name. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-12pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groupsNeil Armstrong
The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_* group names were missing. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-06-11Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-bootTom Rini
- Add Ethernet support for STM32MP1 - Add saveenv support for STM32MP1 - Add STM32MP1 Avenger96 board support - Add SPI driver suport for STM32MP1 - Add watchdog support for STM32MP1 - Update power supply check via USB TYPE-C for STM32MP1 discovery board
2019-06-11Merge tag 'u-boot-imx-20190612' of git://git.denx.de/u-boot-imxTom Rini
u-boot-imx-20190612 -------------------- - Board fixes: - imx6logic - wandboard - mx6sabre boots again - imx8qm_mek - pico-* boards - Toradex apalis / colibri - engicam imx6 (environment) - KP MX53 - opos6ul - Switch to DM: - vining2000 - dh MX6 - Toradex colibri i.MX7 - Novena - Security : fix CSF size for HAB - Other: - imx: fix building for i.mx8 without spl - pcie and switch to DM mx6sabreauto: Enable SPL SDP support
2019-06-11configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORTHeinrich Schuchardt
The SPL for the Tinker Board has to fit into 32 KiB. Currently this limit is exceeded. CONFIG_SPL_I2C_SUPPORT is not needed to move to main U-Boot. So let's disable it. Suggested-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-06-11spl: imx6: Provide a SPL_SIZE_LIMIT defaultFabio Estevam
As explained in include/configs/imx6_spl.h. the i.MX6 SPL size limit is 68KB (4KB header + 64KB max size). Provide such limit for all i.MX6 boards that use SPL to detect SPL size overflow in build time. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-06-11mx6sabreauto: Enable SPL SDP supportSjoerd Simons
To allow loading u-boot over USB enable SDP support in the SPL. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-06-11mx6sabreauto: Remove CONFIG_SPL_DM to decrease the SPL sizeSjoerd Simons
The i.mx6 SPL binary cannot be bigger then 68K, while with the current defconfig for sabreauto it's only about 56K as soon as USB support gets added the size will overflows. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-06-11arm: dts: imx6qdl-u-boot: Alias usb0 to usbotgSjoerd Simons
All i.mx6 boards seems to have moved to DM_USB, however gadget support for mx6 is still pre-DM as CI_UDC isn't converted yet. To make this work the usb otg controller used for gadgets needs to be usb number 0. Add an alias for this directly in the main u-boot mx6qdl dtsi so it doesn't need to be done for each board separately. This fixes regressions wrt. usb gadget functionality in several boards that have gadget functions enabled in their config, but no usb0 alias in their device-tree. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
2019-06-11mx6sabreauto: set SYS_MALLOC_F for videoSjoerd Simons
Sabre Auto boards currently hang with: ``` U-Boot 2019.07-rc3-00057-gc41940c406 (Jun 03 2019 - 14:42:41 +0200) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C)Reset cause: WDOG Model: Freescale i.MX6 Quad Plus SABRE Automotive Board Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28 Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28 Some drivers failed to bind Error binding driver 'generic_simple_bus': -28 Some drivers failed to bind initcall sequence 8ffe00b8 failed at call 1780e93b (err=-28) ``` Set SYS_MALLOC_F_LEN to reserve_video to work. This is similar to the change Peng Fan did for mx6sabresd (9002e735e717) Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-11mx6sabreauto: Select pinctrl driverSjoerd Simons
With the conversion to DM we should select the pinctrl driver. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-11imx8mq_evk: Staticize when appropriateFabio Estevam
Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the following sparse warnings: board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static? board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static? Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-11imx: define ARCH_MXC for i.MX8/8M/7ULPPeng Fan
Without this definition, fsl_esdhc will access reserved registers on i.MX chips, so define ARCH_MXC to fix it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-06-11imx: drop imx-regs.hPeng Fan
imx-regs.h under arch-imx has no user, drop it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-06-11imx8: cpu: get temperature when print cpu descPeng Fan
Read the temperature when print cpu inforation. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-06-11pinctrl: imx: Define imx6_pinctrl_soc_info in .data sectionLukasz Majewski
This commit is necessary to be able to re-use the pinctrl code in early SPL to properly configure pins. The problem is that those "static" structures (without explicit initialization) are placed in the SDRAM area, which corresponds to u-boot proper (not even SPL). Hence, when one wants to configure pins before relocation via DTS/DM, the board hangs (imx6q SoC powered one) as only OCRAM area is available (0x009xxxxx). This commit prevents from this issue by moving the imx6_pinctrl_soc_info structure to data section (from BSS). Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-11net: fec_mxc: not access reserved register on i.MX8Peng Fan
We should not access reserved register on i.MX8, otherwise met SERROR Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
generated by cgit (git 2.34.1) at 2025-02-24 07:47:08 +0000