summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-04-09arm64: zynqmp: Enable ethernet phys for zc1751 dc5Michal Simek
Enable ethernet phys for zc1751 dc5. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable booting to ATFLuca Ceresoli
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which pass control to full u-boot(EL2). This has been tested on zcu106, so enable it in this defconfig. To generate an image that triggers this booting flow, you need to pass '-O arm-trusted-firmware' to mkimage. Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable pxe and dhcp if commands are enabledMichal Simek
Targets without net can't use pxe or dhcp boot methods. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09net: phy: xilinx_phy: Read phytype using property xlnx,phy-typeSiva Durga Prasad Paladugu
This patch reads phytype from property "xlnx,phy-type" instead od simply looking for "phy-type". This is to be inline with Linux and also fixes the issue of detecting it wrongly in u-boot. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09axi: ethernet: Added support for 64 bit addressing for axi-ethernetVipul Kumar
This patch uses writeq() function to enable greater than 32 bit addressing of axi-ethernet for the ZynqMP devices. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09nand: arasan_nfc: Fixed NAND write issueVipul Kumar
In commit 2453c695185f ("arm64: zynqmp: nand: Fixed NAND erase issue for size 1GiB or more"), ARASAN_NAND_MEM_ADDR1_PAGE_MASK macro changed to 0xFFFF and the same macro is used in nand write and so that getting nand write error. This patch reverted this macro to the 0xFFFF0000 and used ARASAN_NAND_MEM_ADDR1_COL_MASK in the nand erase function which is equal to 0xFFFF. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynq: Add delay after PCFG_PROG_B changeSiva Durga Prasad Paladugu
There is delay needed after PCFG_PROGB change if AES key source is efuse. This fixes the issue of encrypted bitstream loading with AES efuse as key source. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynqmp: Fix the nonsecure bitstream loading issueSiva Durga Prasad Paladugu
Xilfpga library expects the size of bitstream in a pointer but currenly we are passing the size as a value. This patch fixes this issue. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynqmp: Update zynqmp_load() as per latest xilfpgaSiva Durga Prasad Paladugu
Latest xilfpga expects to set BIT5 of flags for nonsecure bitsream and also expects length in bytes instead of words This patch does the same. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09fpga: zynqmp: Add support to get the PCAP status for fpga info commandNitin Jain
This patch adds support for ZynqMP platform to print FPGA PCAP status for "fpga status" command. Signed-off-by: Nitin Jain <nitinj@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09clk: zynqmp: Add new compatible string for clock driverMichal Simek
New and old clk drivers are sharing IDs and descriptions. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Use fixed partitions for spi flash for zc770 xm010Michal Simek
Sync with mainline. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Fix eeprom dt nodesMichal Simek
- Use eeprom for node name - Use atmel compatible string instead of at. - Add missing labels Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Add generic compatible string for I2C EEPROMJavier Martinez Canillas
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Use i2c-mux instead of i2cswitch for pca9548Michal Simek
i2c muxes should described like this. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Sync up licenses with mainline kernelMichal Simek
Use different location for SPDX line. Also update dates for new mainline DTS files. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Remove 0x prefixes from cc108Michal Simek
The patch fixing issues reported by DTC: zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0x400000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0x800000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xc00000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xd00000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xf00000 unit name should not have leading "0x" Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove double spaces from dts fileMichal Simek
There is no reason to have double spaces for indentation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add silabs prefix to u69 for zcu102Michal Simek
Add vendor prefix to si5341. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove number from clock-generator node nameMichal Simek
There shouldn't be a number appended based on spec. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove u-boot commands from dts filesMichal Simek
U-Boot commands shouldn't be the part of kernel DTS files. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Update sd properties for dc5Srinivas Goud
This patch adds no-1-8-v below properties to sd node for dc5 board dts. Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable ttcs for zc1751 dc5Michal Simek
Enable TTCs for this target as is done in Linux kernel. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add eeprom reference to eeprom nodesMichal Simek
eeprom can contain information which can be used by nvmem drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use atmel prefix instead of atMichal Simek
This changes was done in mainline and this patch is just following it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Fix spi flash partition definition for zc1751 dc2Michal Simek
Using different node name and label partitions as data. Also use latest compatible strings based on mainline review. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use s/_/-/g in node name for zcu102 rev1.0Michal Simek
Follow spec for node names. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use keycode from input/input.hMichal Simek
Instead of hardcoding numbers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove additional comments from dts filesMichal Simek
Remove additional comments which were removed as the part of upstreaming. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Sync up license with mainline kernelMichal Simek
Mainline Linux kernel has adopted SPDX header license in a different format then was used before. This patch is syncing it up. Also update years in License text and remove Nathalie's email because it is no longer valid. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use i2c-mux instead of i2cswitch insteadMichal Simek
Based on review from mainline i2c-mux is standard name for i2c switches. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use maxim prefix for all maxim chipsMichal Simek
Use vendor prefix for Maxim chips. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Sync alignment with mainlineMichal Simek
Sync pcie and lpd_dma nodes with mainline version. Incorrect locations are causing diff in statistics that's why synchronizations are needed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09MAINTAINERS: ZYNQMP: correct entriesHeinrich Schuchardt
Replace references to non-existent file. Cc: Michal Simek <michal.simek@xilinx.com> Cc: Michal Simek <monstr@monstr.eu> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09MAINTAINERS: Fix zynqmp clock driver pathMichal Simek
Fix c&p error from Zynq. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Handle ENXIO error return value properlyMichal Simek
zynq_clk_get_rate() is also returning ENXIO which is not handled now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Rename dts for Z-turn boardAnton Gerasimov
Makes naming in line with other Zynq boards. Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Update dts for Z-turn boardAnton Gerasimov
Delete devices implemented in PL, stylistic changes. Signed-off-by: Anton Gerasimov <tossel@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-08treewide: Convert CONFIG_HOSTNAME to a string optionMario Six
CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every use is couched by __stringify(...). Hence, convert it to a proper string option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to KconfigMario Six
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_LAST_STAGE_INIT to KconfigMario Six
Migrate the CONFIG_LAST_STAGE_INIT option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to KconfigMario Six
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_SYS_ALT_MEMTEST to KconfigMario Six
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc> [trini: Re-run migration after also including CMD_MEMTEST] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07configs: Finish migration of CONFIG_ATMEL_SPITom Rini
With the previous temporary reverts, we need to re-complete the migration of CONFIG_ATMEL_SPI here now. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07Revert "spi: atmel: Drop non-dm code"Tom Rini
As we aren't quite able to convert some platforms with a very small size limit in SPL yet, we need to revert this for now. This reverts commit 7b0947787358c6b277431d6b76ce043d8bec641d. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07Revert "spi: atmel: Drop atmel_spi.h"Tom Rini
As we aren't quite able to convert some platforms with a very small size limit in SPL yet, we need to revert this for now. This reverts commit 37434db29be495ef41f204a97b8bf13b1418f97d. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-06cmd: Add command for calculating binary operationsMario Six
This patch adds a command that enables the calculation of bit operations (AND, OR, XOR) on binary data from the command line. Memory locations as well as the contents of environment variables are eligible as sources and destination of the binary data used in the operations. The possible applications are manifold: Setting specific bits in registers using the regular read-OR-write pattern, masking out bits in bit values, implementation of simple OTP encryption using the XOR operation, etc. Signed-off-by: Mario Six <mario.six@gdsys.cc>
generated by cgit (git 2.34.1) at 2025-01-15 05:32:20 +0000