summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-16Makefile: Prioritize external dtb if definedMichal Simek
Prioritize external dtb if its passed via EXT_DTB than the dtb that was built in the tree. With this patch it appends the specified external dtb to the u-boot image. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-16arm: zynq: Add an info message about post configSiva Durga Prasad Paladugu
Post configuration cant be run at u-boot as u-boot didn't has any info about the design.So,this patch adds an info message that post config was not run and needs to be run manually if needed. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Add idcode for new RFSoC silicon ZU39DRSiva Durga Prasad Paladugu
This patch adds "zu39dr" to the list of zynqmp devices The zu39DR is the new RFSoC silicon with id value of 0x66. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16ARM: zynq: fix environment command syntaxMelin Tomas
Update EXTRA_ENV_SETTINGS and related commands to use 'setenv' instead of short name 'set' in commands. E.g. in case command setexpr is enabled the short form does not work properly as the name becomes ambigous. Fixes error messages like: U-Boot> set Unknown command 'set' - try 'help' Signed-off-by: Tomas Melin <tomas.melin@vaisala.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16ARM: zynq: Add missing i2c get_rate for fixing i2c SPLHannes Schmelzer
The commit 'f48ef0d81aa837a33020f8d61abb3929ba613774' did break I2C support because requesting the clock for the I2C ip-block isn't supported during SPL. To fixup this we add support requesting clocks for: - i2c0 - i2c1 Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: xilinx: zynqmp: Remove unneeded configsSiva Durga Prasad Paladugu
Remove unneeded configs from mini qspi configuration so that it saves space for this mini configuration. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Define label for flash nodeSiva Durga Prasad Paladugu
Define a label for flash node so that it can be referenced easily as required. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Add spi-flash compatible string to flash nodeSiva Durga Prasad Paladugu
spi-flash compatible string is needed for reading tx and rx bus widths, hence add this compatible string to flash node. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Add debug message about clearing BSSMichal Simek
Just have better view on system. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16ARM: zynq: Check zynq aes & rsa command parameters countT Karthik Reddy
This patch checks for zynq aes & rsa commands max parameters count. Also checks minimum number of parameters count for aes command. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Use zynqmp_mmio_read/write functionsT Karthik Reddy
Changed the return type of reset_reason() to int from u32, because zynqmp_mmio_read/write() returns signed value on error. Replaced readl and writel functions with zynqmp_mmio_read & zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16spi: zynqmp_gqspi: Fix tap delay values at 100MHz and 150MHzSiva Durga Prasad Paladugu
This patch fixes the tap delay values to be set at 100MHz and 150MHz as per TRM by fixing the if condition to use <= instead of <. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Disable WDT for zcu100Michal Simek
Do not enable WDT by default on this target because distributions are not enabling watchdog driver to service it. Feature has been enabled by: "arm64: zynqmp: Enable cadence WDT for zcu100" (sha1: 767afebbcda59f3ccb04f6c94de8cab2fb7905b6) And WDT is still enabled in rebranded Avnet Ultra 96 board support. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16test: py: Extend fpga test with fit image with external dataMichal Simek
Images are created mkimage -f fit.its -E download-fit-external.ub and test expects these entries. env__fpga_under_test = { ... "mkimage_fit_external": download-fit-external.ub", "mkimage_fit_external_size": xxxxx, ... } Test download file and loads it to fpga. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-16fpga: Replace char * with const char * for filenameTien Fong Chee
Ensure the string for filename is always constant, otherwise it can be corrupted by the writing. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16fpga: Add support for getting external data address and lengthTien Fong Chee
This function supports getting both data address and length for existing FPGA subimage and FPGA external data. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-14Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-13Merge tag 'pull-12apr19' of git://git.denx.de/u-boot-dmTom Rini
fdtdec tests and improvements for carve-outs pinctrl race-condition fix various other fixes in sandbox, sound, mkimage, etc.
2019-04-13Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mipsTom Rini
- mt76xx: add USB support, small fixes - ath79: small fixes, add support for QCA9563 SoC and AP152 reference board - mscc: small fixes, add network support for JR2 and ServalT SoCs - bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs - MIPS: fix redundant relocation of initrd images
2019-04-12Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-bootTom Rini
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2019-04-12Merge git://git.denx.de/u-boot-marvellTom Rini
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
2019-04-12Merge branch '2019-04-11-ti-master-imports'Tom Rini
- Improve Keystone 3 SoC support (DMA, TI SCI) - Improve Keystone 2 SoC support (PHY fixes on various platforms) - Improve am335x families (new platforms, more boot mode options in SPL via DM). - General DaVinci, OMAP5 fixes.
2019-04-12mips: mt76xx: linkit-smart-7688: Enable USB and FS supportStefan Roese
This patch enables USB and file-system support on the LinkIt smart MT7688 module for both, the normal and the RAM default config. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12phy: Add USB PHY driver for the MT76x8 (7628/7688) SoCStefan Roese
This driver is derived from this Linux driver: linux/drivers/phy/ralink/phy-ralink-usb.c The driver sets up power and host mode, but also needs to configure PHY registers for the MT7628 and MT7688. I removed the reset controller handling for the USB host and device, as it does not seem to be necessary right now. The soft reset bits for both devices are enabled by default and testing has shown (with hackish reset handling added), that USB related commands work identical with or without the reset handling. Please note that the resulting USB support is tested only very minimal. I was able to detect one of my 3 currently available USB sticks. Perhaps some further work is needed to fully support the EHCI controller integrated in the MT76x8 SoC. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12configs: mscc_servalt: Add network supportHoratiu Vultur
Update default config to use network driver for ServalT SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12net: mscc: servalt: Add ethernet nodes for ServalTHoratiu Vultur
Add ethernet nodes for ServalT SoCs family. Currently there is only one pcb(pcb116) in this family. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12net: Add MSCC ServalT network driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch. It is present on ServalT SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12configs: vcoreiii: Change CONFIG_ENV_SIZEHoratiu Vultur
Shrink the environment size for 3 reasons: - reading the environment it is slow, therefore having a smaller env improves the speed. - usually in the environment there are only few variables, therefore the enviromnent is almost empty. - because the same image can run on different boards which may have different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE can't be change, it is set to least common multiple of the page sizes. Adding this change improves the boot time. Before update for reading the entire environment it took ~850 msec, after the change it takes ~40 msecs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12configs: mscc_jr2: Add network supportHoratiu Vultur
Update default confing to use network driver for Jaguar2 SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12net: mscc: jaguar2: Add ethenet nodes for Jaguar2.Horatiu Vultur
Add ethernet nodes for Jaguar2 SoCs family. There are 3 pcb in this family: pcb110, pcb111 and pcb112. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12board: mscc: jr2: Update MSCC Jaguar2 boardsHoratiu Vultur
In Jaguar2 SoC family there are 3 different pcb. Each of this needs to configure the phys in different ways. Therefore implement the function board_phy_config and based on pcb configure them accordingly. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12net: Add MSCC Jaguar2 network driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch. It is present on Jaguar2 SoCs. Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12bcm963158: enable gpio supportPhilippe Reynes
Enable the gpio support (driver and command) in the configuration of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12dt: bcm963158: enable gpio controllerPhilippe Reynes
Enable all the gpio controllers in the device tree of the board bcm963158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12dt: bcm63158: add gpio controllerPhilippe Reynes
Add 8 gpio controllers in the bcm63158 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: do not include <asm/arch/gpio.h> on ARCH_BCM63158Philippe Reynes
As no gpio.h is defined for this architecture, to avoid a compilation failure, do not include <asm/arch/gpio.h> for arch bcm63158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: bcm6345: allow this driver on ARCH_BCM63158Philippe Reynes
This IP is also used on some arm SoC, so we allow to use this driver on arch bcm63158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12bcm968580xref: enable gpio supportPhilippe Reynes
Enable the gpio support (driver and command) in the configuration of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12dt: bcm968580xref: enable gpio controllerPhilippe Reynes
Enable all the gpio controllers in the device tree of the board bcm968580xref. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12dt: bcm6858: add gpio controllerPhilippe Reynes
Add 8 gpio controllers in the bcm6858 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: do not include <asm/arch/gpio.h> on ARCH_BCM6858Philippe Reynes
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch bcm6858. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: bcm6345: allow this driver on ARCH_BCM6858Philippe Reynes
This IP is also used on some arm SoC, so we allow to use this driver on arch bcm6858. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12bcm968380gerg: enable gpio supportPhilippe Reynes
Enable the gpio support (driver and command) in the configuration of the board bcm968380gerg Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12dt: bcm968380gerg: enable gpio controllerPhilippe Reynes
Enable the gpio controllers in the device tree of the board bcm968380gerg. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12dt: bcm6838: add gpio controllerPhilippe Reynes
Add gpio controllers in bcm6838 device tree. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12gpio: bcm6345: switch to raw I/O functionsPhilippe Reynes
This driver is used on several big endian mips board. So we could use raw I/O function instead of forcing big endian access. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12ag7xxx: add initial support for s17Rosy Song
S17 ethernet support is for QCA8337N, which used on AP152 (QCA9563) board. It is a 7 ports GbE switch. Signed-off-by: Rosy Song <rosysong@rosinson.com> Changes for v2-v3: - add more commit message for s17 Changes for v4-v5: - coding style cleanup
2019-04-12mips: add initial support for qca956x referenced boardRosy Song
QCA9563 is CPU used on AP152 board : Clock speed : 750 MHz , Arch : Mips 74Kc, Eth : SGMII interface, MIMO config : 3 * 3 450M, 2 * USB 2.0, Signed-off-by: Rosy Song <rosysong@rosinson.com> Changes for v2: - coding style cleanup - remove ununsed flash chip in defconfig - enable automatic icache / dcache size in defconfig Changes for v3: - add detailed information for qca956x in commit message Changes for v4: - remove pre-configured network settings in ap152.h Changes for v5: - coding style cleanup
generated by cgit (git 2.34.1) at 2025-01-18 13:20:45 +0000