| Age | Commit message (Expand) | Author |
|---|
| 2012-09-01 | am33xx: Clean up unused DDR defines, prefix more with 'DDR2' | Tom Rini |
| 2012-09-01 | am33xx: Move the call to ddr_pll_config, make it take the frequency | Tom Rini |
| 2012-09-01 | am33xx: Pass to config_ddr the type of memory that is connected | Tom Rini |
| 2012-09-01 | am33xx: Make config_cmd_ctrl / config_ddr_data take const structs | Tom Rini |
| 2012-09-01 | am33xx: Rework DDR2 EMIF initalization slightly | Tom Rini |
| 2012-09-01 | am33xx: Bugfix to config_sdram() | Tom Rini |
| 2012-09-01 | am33xx: Remove extra check in enable_ddr_clocks | Tom Rini |
| 2012-09-01 | am33xx: Convert to using <asm/emif.h> to describe the EMIF | Tom Rini |
| 2012-09-01 | am33xx: Remove DMM_BASE define | Tom Rini |
| 2012-09-01 | am335x_evm: Update config for common usage | Tom Rini |
| 2012-09-01 | am33xx: Enable gpio0 clock | Tom Rini |
| 2012-09-01 | OMAP3: igep00x0: add SPL support for IGEP-based boards | Javier Martinez Canillas |
| 2012-09-01 | OMAP3: mem: Add Numonyx OneNAND 200MHz timing information | Javier Martinez Canillas |
| 2012-09-01 | OMAP3: igep00x0: Add config option to choose flash storage memory | Javier Martinez Canillas |
| 2012-09-01 | am335x_evm: CPSW support | Chandan Nath |
| 2012-09-01 | am335x_evm: read the on-board EEPROM | Ilya Yanok |
| 2012-09-01 | am33xx: pin mux defintions for CPSW switch | Chandan Nath |
| 2012-09-01 | am33xx: CPSW init and definitions | Chandan Nath |
| 2012-09-01 | cpsw: add driver for cpsw ethernet device | Cyril Chemparathy |
| 2012-09-01 | beagle: only call DSS code when #defined CONFIG_VIDEO_OMAP3 | Peter Meerwald |
| 2012-09-01 | serial/ns16550: ns16550 has a different register layout on SOC_DA8XX | Mikhail Kshevetskiy |
| 2012-09-01 | arm/davinci/da850: add uart0 pinmux | Mikhail Kshevetskiy |
| 2012-09-01 | arm/davinci: fix DDR2/mDDR memory controller initialization for Omap L138 | Mikhail Kshevetskiy |
| 2012-09-01 | Revert "arm: armv7: add compile option -mno-unaligned-access if available" | Albert ARIBAUD |
| 2012-09-01 | omap: am335x_evm: enable i2c1 channel | Steve Sakoman |
| 2012-09-01 | beagle: removed unused pr_debug #define | Peter Meerwald |
| 2012-09-01 | beagle: fix termination of buddy env setting | Peter Meerwald |
| 2012-09-01 | beagle: make get_expansion_id(), get_board_revision(), beagle_display_init() ... | Peter Meerwald |
| 2012-09-01 | igep00x0: default mmcrootfstype to EXT4 | Javier Martinez Canillas |
| 2012-09-01 | igep00x0: default to OMAP-specific serial driver | Javier Martinez Canillas |
| 2012-09-01 | da850/omap-l138: add support for direct NOR boot mode | Lad, Prabhakar |
| 2012-09-01 | da850/omap-l138: Add support for NAND SPL | Lad, Prabhakar |
| 2012-09-01 | da850/omap-l138: Fix NAND flash timings | Lad, Prabhakar |
| 2012-09-01 | da850/omap-l138: Add support to read u-boot image from MMC/SD | Lad, Prabhakar |
| 2012-09-01 | da850/omap-l138: Define SPI specific configs for SPL only when SPI is used | Lad, Prabhakar |
| 2012-09-01 | arm, davinci: perform check for initializing global data and serial init | Lad, Prabhakar |
| 2012-09-01 | da850/omap-l138: Make MMC and NOR support mutually exclusive | Rajashekhara, Sudhakar |
| 2012-09-01 | da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM | Rajashekhara, Sudhakar |
| 2012-09-01 | da850/omap-l138: Add MMC support for DA850/OMAP-L138 | Lad, Prabhakar |
| 2012-09-01 | omap: am33xx: enable gpio support | Steve Sakoman |
| 2012-09-01 | omap: am335x_evm: remove unused definitions | Steve Sakoman |
| 2012-09-01 | OMAP3: mcx: read hot-water-button after reset | Stefano Babic |
| 2012-09-01 | OMAP3: mcx: updated default environment | Stefano Babic |
| 2012-09-01 | OMAP3: mcx: set pinmux for uart4 | Stefano Babic |
| 2012-09-01 | mcx: increased buffer for command line | Stefano Babic |
| 2012-09-01 | arm: omap3: cm-t35: minor comment and printf change | Igor Grinberg |
| 2012-09-01 | hawkboard/omapl-138: Add support for generating ais image for hawkboard | Sughosh Ganu |
| 2012-09-01 | omap24xx_i2c: add 2-byte address support | Ilya Yanok |
| 2012-09-01 | CREDITS: Add credits for MCF5249 initialization code | Jeremy Andrus |
| 2012-09-01 | Consolidate bootcount code into drivers/bootcount | Stefan Roese |
