| Age | Commit message (Collapse) | Author |
|---|
|
Indexes of reset signals available in PRCI driver are also
defined in include/dt-bindings/reset/sifive-fu540-prci.h.
So use those instead of defining new ones again within the
fu540-prci driver.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
|
|
Add bit indexes for reset signals within the PRCI module
on FU540-C000 SoC.
The DDR and ethernet sub-system's have reset signals
indicated by these reset indexes.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
|
|
Since commit 7812bbdc3732 ("video: Correctly handle multiple
framebuffers") the vidconsole output is missing on the primary
display on boards with two IPU units (all i.MX6Q/D based boards).
The base address of the allocated framebuffer is not correctly
programmed in the display controller. Fix it.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
|
|
Migration to DM_VIDEO changed the output device name (in stout, stderr)
from 'vga' to 'vidconsole'. This also was adapted in the default environment.
However, existing user defined environments still use 'vga'. Enable this
workaround to map the 'vga' name to 'vidconsole'. So we get HDMI video
output also with existing legacy environments.
Signed-off-by: Soeren Moch <smoch@web.de>
|
|
This patch enables the following options for the Octeon EBB7304 EVB:
- PCI & DM_PCI
- DM_SPI_FLASH & SPI flash device support
- SPI & Octeon SPI driver
- GPIO cmd support
- I2C cmd support
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add the SPI flash DT node for the EBB7304.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add the Octeon SPI DT node to the dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Adds support for SPI controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch adds the DT nodes for the Octeon clock support via the
common clk_ API.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds a simple clock driver for the Marvell Octeon MIPS SoC
family. Its for IO clock rate passing via DT in some of the Octeon
driver, like I2C. So that we don't need to use the non-mainline API
octeon_get_io_clock().
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
|
|
Add I2C DT nodes to the Octeon dts / dtsi files.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add the Octeon GPIO DT node to the dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add support for GPIO controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Correct the make commands for the defconfigs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Before enable _DM_ETH:
Net: FEC [PRIME]
After enable DM_ETH:
Net: eth0: ethernet@2188000
Here is the test commands:
=> dhcp
BOOTP broadcast 1
DHCP client bound to address 10.88.88.152 (146 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=> ping 8.8.8.8
Using ethernet@2188000 device
host 8.8.8.8 is alive
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
|
|
Enlarge CONFIG_SYS_BOOTM_LEN when booting FIT image with AArch32 mode
Linux kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR,
modify the offset of U-boot proper in the SPI NOR, so the
difference in offset matches between SPL and U-boot matches that of
the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI
NOR at an offset of 0x400. Update the README to reflect this
change.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Instead of hang()ing the system and thus disallowing any automated
recovery possibility from a HAB authentication failure, panic() .
The panic() function can be configured to hang() the system after
printing an error message, however the default is to reset the
system instead.
This allows redundant boot to work correctly. In case the primary
or secondary image cannot be authenticated, the system reboots and
bootrom can try to start the other one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
|
|
- ApolloLake: add u64 parameters support for FSP2 bindings
- ApolloLake: add missing parameters to support full configuration of
the latest FSP MR6 release
- Append appropriate suffixes in various assembly codes
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc2
This series comprises error corrections for the UEFI subsystem:
* make the memory size reserved for the U-Boot stack customizable
and reduce it for the MAIX board
* correct build dependencies for UEFI unit test
* enable read-only UEFI variable are enabled with the TEE backend
* add 10 ms wait to sysreset to fix a problem with unit testing
|
|
Assembler is not happy:
arch/x86/cpu/call32.S: Assembler messages:
arch/x86/cpu/call32.S:36: Warning: no instruction mnemonic suffix given and no register operands; using default for `retf'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 6f92ed8f1abf ("x86: Add a way to call 32-bit code from 64-bit mode")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Assembler is not happy:
arch/x86/cpu/sipi_vector.S: Assembler messages:
arch/x86/cpu/sipi_vector.S:134: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
arch/x86/cpu/sipi_vector.S:139: Warning: no instruction mnemonic suffix given and no register operands; using default for `bts'
arch/x86/cpu/sipi_vector.S:157: Warning: no instruction mnemonic suffix given and no register operands; using default for `cmp'
Fix this by adding appropriate suffixes to the assembler commands.
Fixes: 45b5a37836d5 ("x86: Add multi-processor init")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add missing parameters to support full configuration of the latest FSP
MR6 release.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add FSP_UINT64 read support as preparation for FSP-M and FSP-S parameter
update.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Fix some typos in arch/x86/include/asm/irq.h.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Enable these extra PCI ethernet devices, so they can be tested in CI.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Switch r2dplus to DM and DT probing for serial and clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add simple DT and clock bindings to r2dplus DT to permit U-Boot
to bind the SCIF driver via DT probing instead of hard-coded
config options.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The gd->malloc_base must be set before the C runtime if the MALLOC_F_LEN
is non-zero, otherwise we hit assertion in dlmalloc.c initf_malloc(). So
set it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The ethernet on r2dplus is on PCI bus, enumerate the PCI early
to get the ethernet operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Enable DM ethernet support for the board, now that rtl8139 is converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
As both MMC and GPIO driver now supports OF_PLATDATA, enable it in
defconfig in order to reduce the SPL footprint. After applying this
setting the SPL reduction is 5 KB, which partially compensates the
increment due to DM.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Continuing with the approach in commit <addf358bac1d2bd0> rename
additional drivers to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
After enabling OF_PLATDATA support to both MMC and GPIO drivers add the
support for card detection.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Continuing with the OF_PLATADATA support for iMX6 to reduce SPL
footprint, add it to mxc_gpio. Thanks to this, it will be possible to
enable card detection on MMC driver.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
|
|
In order to reduce the footprint of SPL by removing dtb and library
overhead, add OF_PLATDATA support to fsl_esdhc_imx. This initial
approach does not support card detection, which will be enabled after
adding OF_PLATDATA support to GPIO.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As discussed in commit <addf358bac1d2bd0> rename fsl_esdhc_imx
driver to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Do not execute the block device test if CONFIG_DOS_PARTITION=n.
Imply CONFIG_DOS_PARTITION in Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
If CONFIG_NET=n, testing the simple network protocol makes no sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
In our Python tests we expect to see the word "resetting". It may be
truncated if we reset before the serial console buffer is transferred.
Wait for 100 ms between the "resetting ..." message and the actual reset
like we do when powering off.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The K210 has only 8 MiB RAM thereof 2 MiB reserved for AI.
Allow only 1 MiB for the stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The Kconfig symbol CONFIG_STACK_SIZE is used both by ARM and Microblaze
with the same meaning. Move it to menu 'General setup' so that we can use
it for all architectures.
Use the value of CONFIG_STACK_SIZE instead of a hard coded 16 MiB value for
reserving memory in the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Configuration variables should have the same meaning independent of the
architecture. x86 and ARM both use CONFIG_STACK_SIZE:
* x86: U-Boot's runtime stack size during reboot
* ARM: max stack size that can be used by U-Boot
Rename the x86 configuration variable to CONFIG_STACK_SIZE_REBOOT
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
We recently added functions for storing/restoring variables
from a file to a memory backed buffer marked as __efi_runtime_data
commit f1f990a8c958 ("efi_loader: memory buffer for variables")
commit 5f7dcf079de8 ("efi_loader: UEFI variable persistence")
Using the same idea we now can support GetVariable() and GetNextVariable()
on the OP-TEE based variables as well.
So let's re-arrange the code a bit and move the commmon code for
accessing variables out of efi_variable.c. Create common functions for
reading variables from memory that both implementations can use on
run-time. Then just use those functions in the run-time variants of the
OP-TEE based EFI variable implementation and initialize the memory
buffer on ExitBootServices()
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The current code does not trim the output buffer correctly.
In fact it doesn't trim the buffer at all, since it calculates a wrong
value for it, which isn't even applied.
So let's remove the unused temporary size variable and trim the buffer
correctly.
Since we are editing efi_get_next_variable_name_int(), fix an indentation
error along the way.
Fixes: f042e47e8fb43 ("efi_loader: Implement EFI variable handling via OP-TEE")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous conversion to (u8 *) for memcpy argument.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
- Fix EFI selftest to not force setting serial# environment (and also
get the U-Boot prompt dynamically).
- Support for append only environment and other related features.
- Improved ext4 environment support
- Fix the case of fw_setenv being used on flash devices that were not
already locked.
|
|
With current implementation of fw_setenv, it is always locks u-boot-env
region if lock interface is implemented for such mtd device. You can
not control lock of this region with fw_setenv, there is no option for
it in config or in application itself. Because of this situation may
happen problems like in this thread on xilinx forum:
https://forums.xilinx.com/t5/Embedded-Linux/Flash-be-locked-after-use-fw-setenv-from-user-space
/td-p/1027851
A short summary of that link is: some person has issue with some spi
chip which has lock interface but doesn't locks properly which leads to
lock of whole flash memory on lock of u-boot-env region. As resulted
solution hack was added into spi-nor.c driver for this chip with lock
disablement.
Instead fix this problem by adding logic to fw_setenv only lock the
flash if it was already locked when we attempted to use it.
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
|
|
This option marks any U-Boot variable which does not have explicit 'w'
writeable flag set as read-only. This way the environment can be locked
down and only variables explicitly configured to be writeable can ever
be changed by either 'env import', 'env set' or loading user environment
from environment storage.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
