summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-07-23Add TQ Systems TQMa6 board supportMarkus Niebel
This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-07-23arm, imx6: add aristainetos boardHeiko Schocher
CPU: Freescale i.MX6DL rev1.1 at 792 MHz Board: aristaitenos I2C: ready DRAM: 1 GiB NAND: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB Display: lb07wv8 (800x480) - UART5 is console - MMC 0 and 1 - USB 0 and 1 - boot from mmc0 and spi nor flash - Splash screen support Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-07-23spi: add config option to enable the WP pin function on st micron flashesHeiko Schocher
enable the W#/Vpp signal to disable writing to the status register on ST MICRON flashes like the N25Q128 thorugh the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-07-23i.MX6: add enable_spi_clk()Heiko Schocher
add enable_spi_clk(), so board code can enable spi clocks. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de>
2014-07-23pwm, imx6: add support for pwm modul on imx6Heiko Schocher
add basic support for the pwm modul found on imx6. Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c Commit "cd3de83f1476 Linux 3.16-rc4" Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2014-07-23i.MX6: define struct pwm_regs and PWMCR_* definesHeiko Schocher
add defines for pwm modul found on imx6. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-07-23imx6: add gpr2 usb_otg_id iomux select control defineHeiko Schocher
add IOMUXC_GPR1_USB_OTG_ID_OFFSET and IOMUXC_GPR1_USB_OTG_ID_SEL_MASK define for the USB_OTG_ID_SEL bit. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23arm: mxs: Scrub useless ifdefMarek Vasut
As a result of 0defddc851edfc34bcf3c3379fe74b11dc01a493 , which did a consolidation of the prompt string, this ifdef became empty. Remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
2014-07-23mx6: Adjust the GPR offset for mx6soloxFabio Estevam
On mx6solox there is an additional 0x4000 offset for the GPR registers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23mx6: Remove duplication of iomuxc structureFabio Estevam
There is no need to keep iomuxc_base_regs structure as it serves the exact same purpose of the iomuxc structure, which is to provide access to the GPR registers. The additional fields of iomuxc_base_regs are not used. Other advantage of 'iomuxc' is that it has a shorter name and the variable declarations can fit into a single line. So remove iomuxc_base_regs structure and use iomuxc instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23mx6sxsabresd: Add PFUZE100 PMIC supportFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-23mx6: soc: Do not apply the PFD erratum for mx6soloxFabio Estevam
The PFD issue is not present on mx6solox, so skip it in this case. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-23embestmx6boards: convert to generic boardIain Paton
Enable CONFIG_SYS_GENERIC_BOARD to remove warning on boot. Signed-off-by: Iain Paton <ipaton0@gmail.com>
2014-07-16Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Conflicts: boards.cfg
2014-07-14Prepare v2014.07Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-07-14socfpga: timer actually counts downPavel Machek
Timer on cyclone5 actually counts down. It took me a while to figure out, as timer counting in wrong direction actually _can_ be used, it just appears to tick at extremely high frequency in u-boot. The bug was introduced in commit 23ab7ee0ffa9d5efd0b4ad830befba306d24a327. Signed-off-by: Pavel Machek <pavel@denx.de> Acked-by: Marek Vasut <marex@denx.de>
2014-07-14ARM: DRA7xx: Update the board_name env variableLokesh Vutla
Update the board_name env variable and accordingly populate the dtb file. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-14boards.cfg: change "<none>" in the board field to "-"Masahiro Yamada
In the previous commit, all the board fields were filled. Now we can use "-" in the board field for a different meaning. Going forward, "-" stands for no board directory as in cpu, soc, vendor fields. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-14boards.cfg: keep it sorted filling the board fieldMasahiro Yamada
The boards.cfg file has allowed to use "-" for the board (= 6th) field if the board name is the same as the 7th field. But I notice one problem. Because tools/reformat.py sorts the lines in the simple alphabetical order (= the order of character code), some entries for the same board are not lined up together. For example, "bf527-ezkit" and "bf527-ezkit-v2" share the same board. But they are located separately because "bf527-ezkit" fills the board field with "-" whereas "bf527-ezkit-v2" specifies it explicitely. The similar things can be seen: - between "trizepsive" and "polaris" - between "RRvision" and "RRvision_LCD" - between "korat" and "korat_perm" - between "lwmon5" and "lcd4_lwmon5" This commit was generated by the following command: awk '$6 == "-" { $6 = $7 } { print }' boards.cfg \ | tools/reformat.py -i -d '-' -s 8 > boards0.cfg; \ mv boards0.cfg boards.cfg Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-11Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-07-10mx6sx: Add initial support for mx6sxsabresd boardFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10mx6: clock: Do not enable sata and ipu clocksFabio Estevam
mx6sx does not have sata nor ipu blocks, so do not handle such clocks. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10mx6sx: Add pin definitionsFabio Estevam
Add the pin definitions for mx6sx. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10mx6: Add support for the mx6solox variantFabio Estevam
mx6solox is the newest member of the mx6 family. Some of the new features on this variants are: - Cortex M4 microcontroller (besides the CortexA9) - Dual Gigabit Ethernet Add the initial support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10i.MX6DL/S: add drive-strength back to pads DISP0_DAT2/DAT10Eric Nelson
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not set in the same way as DISP0_DAT00-23, causing much flicker in parallel RGB displays on Dual-Lite and Solo processors. These settings now match the i.MX6 Dual and Quad core versions. Note that this fixes a regression in commit b47abc3 and that this is the second time we've had a regression on these two pads (See commit e654ddf). Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-07-09usb: phy: omap_usb_phy: implement usb_phy_power() for AM437xFelipe Balbi
Newer AM437x silicon requires us to explicitly power up the USB2 PHY. By implementing usb_phy_power() we can achieve that. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09usb: host: xhci: make sure to power up PHYFelipe Balbi
some boards won't work if the PHY isn't explicitly powered up. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09doc: Add zynq fragment to git-mailrc fileMichal Simek
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-07-09ARM: OMAP4/5: Change omap4_sdp/panda and omap5_uevm maintainerLokesh Vutla
Updating omap4_sdp/panda and omap5_uevm maintainer. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: R Sricharan <r.sricharan@ti.com>
2014-07-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-07-09mx6: soc: Update the comments of set_ldo_voltage()Fabio Estevam
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces set_ldo_voltage() function that can be used to set the voltages of any of the three LDO regulators controlled by the PMU_REG_CORE register. Prior to this commit there was a single set_vddsoc() which only configured the VDDSOC regulator. Update the comments to align with the new set_ldo_voltage() implementation. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-09MX6: Correct calculation of PLL_SYSAndre Renaud
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do the shift after the multiply to avoid rounding errors Signed-off-by: Andre Renaud <andre@bluewatersys.com>
2014-07-09ARM: m53evk: Update default environmentLothar Rubusch
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Lothar Rubusch <lothar@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-07-09ARM: m53evk: Adjust mtdparts settingsMarek Vasut
Adjust the mtdparts settings to allow for alternative boot images and for using UBI. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-07-09ARM: m53evk: add needed commands and optionsMarek Vasut
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-07-09ARM: m28evk: Update default environmentLothar Rubusch
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Lothar Rubusch <lothar@denx.de>
2014-07-09ARM: m28evk: Adjust mtdpartsMarek Vasut
Adjust the mtdparts to also consider factory-programmed config block. Signed-off-by: Marek Vasut <marex@denx.de>
2014-07-09ARM: m28evk: add needed commands and optionsMarek Vasut
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-07-07Merge branch 'tom' of git://git.denx.de/u-boot-x86Tom Rini
2014-07-07TI:omap3: enable CONFIG_CMD_DHCP for omap3_beagleTyler Baker
The following patch re-enables the dhcp functionality on omap3_beagle. It was removed with df4dbb5df6ab1c1d27b3fd4acbaad69b47095daf when omap3_beagle was converted to use ti_omap3_common.h. I have tested beagleboard and beagleboard-xm with this patch and confirmed dhcp is working. Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
2014-07-07kmake: include DTB section into u-boot.bin if CONFIG_OF_EMBED enabledAlexey Ignatov
Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting u-boot.bin, so u-boot was unable to find embedded DTB.
2014-07-07git-mailrc: Add sunxi custodians.Ian Campbell
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-07-07fit: make sha256 support optionalDirk Eibach
sha256 has some beefy memory footprint. Make it optional for constrained systems. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Remove commands to reduce footprintDirk Eibach
Commit "2842c1c fit: add sha256 support" badly increased memory footprint, so some of our boards did not build anymore. Since monitor base must not be changed I removed some commands to save memory. Maybe making sha256 optional for fit would be an option for the future since it really has some beefy footprint. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: iocon: Modify iocon hardware startupDirk Eibach
To avoid peer "ChReceivePathStatus"-messages on iocon startup, initialize PHYs as soon as possible. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Enable scrambling on DP501Dirk Eibach
For proper displayport performance, scrambling has to be enabled, but is turned off on DP501 by default. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Make gdsys osd hardware detection more robustDirk Eibach
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Configure bridge on DP501 to support DDC onlyDirk Eibach
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default. Allow EDID only to avoid I2C address conflicts. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Increase iocon and dlv10g version stringDirk Eibach
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07board: gdsys: Fix dlvision-10g I2C configurationDirk Eibach
PPC4xx config options were not complete. ICS8N3QV01 and SIL1178 needed some more configuration. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
generated by cgit (git 2.34.1) at 2024-12-29 07:19:08 +0000