| Age | Commit message (Collapse) | Author |
|---|
|
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This operation may fail. Retry it a few times before giving up and report
a failure.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.
Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This function can also be used for eMMC devices.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
sequence"
This reverts commit 318a7a576bc49aa8b4207e694d3fbd48c663d6ac.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The response type of CMD25 is R1 instead of R1b.
Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Card detect function implemented for SDHCI framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
|
|
- First round of TI Davinci updates
- Some OMAP3 DM updates
- Other misc updates
|
|
This test is currently broken so disable it for now.
Cc: Ramon Fried <ramon.fried@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Fixed regulators don't have a set_value method. Therefore, trying to
set their value will always return -ENOSYS.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The da850.dtsi file had some changes. This patch pulls in the
changes from Kernel 5.1.9
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL). If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away. This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals. This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.
To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
palmas/lp873x/lp87565
Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.
CPU : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
eth0: ethernet@4a100000
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART
- USB (host)
Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")
Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
|
|
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
|
|
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
[...]
CC drivers/usb/gadget/f_mass_storage.o
CC drivers/usb/musb-new/omap2430.o
CC drivers/usb/gadget/f_fastboot.o
CC env/common.o
CC env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
ret = musb_register(&platdata->plat,
^
LD drivers/usb/host/built-in.o
CC drivers/usb/gadget/f_sdp.o
CC fs/ext4/ext4fs.o
[...]
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
add m41t11 support in ds1307 driver. changes:
- add compatible string for m41t11
- check if RTC clock is running, if not
enable the clock
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.
This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
|
|
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
|
|
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using
This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
`if (!strncmp(dev->name, name, strlen(name)))` might find out
the wrong device, it might find out `dram_pll_ref_sel`, when name is
`dram_pll`. So use strcmp to avoid such issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
"keyb" is not the real device name, "keyb@3" is.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
"adc" is not the real device name, "adc@0" is.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert the board to support the USB and video driver model and remove
the unnecessary code.
|
|
Convert the board to support the USB and video driver model and remove
the unnecessary code.
|
|
This fixes the following error message:
U-Boot 2019.07-rc4-00103-g5eea874b5e (Jun 25 2019 - 15:09:31 +0200)
DRAM: 8 MiB
gpio@40021800: dir_output: error: gpio GPIOG14 not reserved
gpio@40021800: dir_output: error: gpio GPIOG13 not reserved
gpio@40021800: set_value: error: gpio GPIOG14 not reserved
Flash: 2 MiB
....
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As compatible string "st,stm32-gpio" is no more used, .ofmatch
callback becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Since pinctrl_stm32 driver update, each gpio bank is now binded
by pinctrl driver. The compatible string "st,stm32-gpio" becomes
useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Update .bind callback in order to bind all pinctrl subnodes
with "gpio-controller" property to gpio_stm32 driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
