summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-09-02Blackfin: cm-bf548: fix device->stdio_dev falloutMike Frysinger
The recent 52cb4d4fb348 commit which renamed device to stdio_dev missed the cm-bf548's video board. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: enable 64bit printf for nandMike Frysinger
Since the NAND code now uses 64bit code, make sure we enable support for ADI Blackfin boards in printf to avoid the warning: nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output! Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: use scratch pad for exception stackMike Frysinger
If the memory layout pushes the stack out of the default DCPLB coverage, the exception handler may trigger a double fault by trying to push onto the uncovered stack. So handle the exception stack similar to the kernel by using the top of the scratch pad SRAM. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: increase default console sizeMike Frysinger
The default console size indirectly applies to length of env vars, so a smaller length makes it hard to pass longer command lines to kernels. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: fix debug printf modifiersMike Frysinger
The display_global_data() function generated warnings with pretty much every variable. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: cm-bf537u: new board portHarald Krapfenbauer
The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: change global data register from P5 to P3Robin Getz
Since the Blackfin ABI favors higher scratch registers by default, use the last scratch register (P3) for global data rather than the first (P5). This allows the compiler's register allocator to use higher number scratch P registers, which in turn better matches the Blackfin instruction set, which reduces the size of U-Boot by more than 1024 bytes... Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: enable more network commands for ADI dev boardsRobin Getz
Add dns and ntp to default networking commands, and ask for more dhcp options to better configure the network environment. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: bf537-stamp: comment CF-Flash Card Support betterMichael Hennerich
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-02Blackfin: use +(filesize) to make sure we are only doing what is necessaryRobin Getz
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-08-31Merge branch 'next' of ../nextWolfgang Denk
2009-08-31Prepare 2009.08Wolfgang Denk
Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-31Add common code dir for Matrix Vision boards.Andre Schwarz
This fixes current build failure. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> mvblm7.c: fix warning: implicit declaration of function 'mv_reset_environment' Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-30bugfix CONFIG_SYS_CONSOLE_INFO_QUIETDavid Brownell
The "console: unify printing current devices" patch goofed: CONFIG_SYS_CONSOLE_INFO_QUIET is supposed to *REMOVE* boot time noise, not add it. Said patch changed the #ifndefs to #ifdef; this one restores them to the proper sense. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-08-28fsl: simplify the "mac id" command, improve boot-time informational messageTimur Tabi
The "mac id" command took a 4-character parameter as the identifier string. However, for any given board, only one kind of identifier is acceptable, so it makes no sense to ask the user to type it in. Instead, if the user enters "mac id", the identifier (and also the version, if it's NXID) will automatically be set to the correct value. Improve the message that is displayed when EEPROM is read during boot. It now displays "EEPROM:" and then either an error message or the EEPROM identifier if successful. If the identifier in EEPROM is valid, then always reject a bad CRC, even if the CRC field has not been initialized. Don't force the MAC address count to MAX_NUM_PORTS or less. Forcing the value to be changed resulting in an in-memory copy that does not match what's in hardware, even though the user did not request that change. Finally, always update the CRC value in the in-memory copy after any field is changed, so that the CRC is always correct. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Added PCIe support for P1 P2 RDBPoonam Aggrwal
Call fsl_pci_init_port() to initialize all the PCIe ports on the board. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28driver/fsl_pci: Add fsl_pci_init_port function to initialize a PCI controllerPoonam Aggrwal
fsl_pci_init_port can be called from board specific PCI initialization routines to setup the PCI (or PCIe) controller. This will reduce code redundancy in most of the 85xx/86xx FSL board ports that setup PCI. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Improve MPIC initializationTimur Tabi
The MPIC initialization code for Freescale e500 CPUs was not using I/O accessors, and it was not issuing a read-back to the MPIC after setting mixed mode. This may be the cause of a spurious interrupt on some systems. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Added support for P1011RDB and P2010RDBPoonam Aggrwal
P1011 and P2010 are single core variants of P1010 and P2020 respectively. The board(RDB) will be same. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Added single core members of FSL P1xx/P2xx processors seriesPoonam Aggrwal
P1011 - Single core variant of P1020 P2010 - Single core variant of P2020 Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: P1020RDB Support AddedPoonam Aggrwal
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Added CONFIG_MAX_CPUS for P1020Poonam Aggrwal
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Add L2SRAM Register's macro definitionMingkai Hu
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Fix memory test range on MPC8536DSFelix Radensky
With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END memory test hangs if run without arguments. Set them to sane values, so that all available 512MB of RAM excluding exception vectors at the bottom and u-boot code and stack at the top can be tested. Signed-off-by: Felix Radensky <felix@embedded-sol.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Removed BEDBUG support on P1_P2_RDBKumar Gala
To match all other 85xx platforms we are removing BEDBUG support. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Init pci ethernet cards if we enable any on MPC8572DSKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28xes: Use proper IO access functionsPeter Tyser
Also fix some minor whitespace oddities while we're cleaning up Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Move to a common linker scriptKumar Gala
There are really no differences between all the 85xx linker scripts so we can just move to a single common one. Board code is still able to override the common one if need be. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Added P1020 Processor Support.Poonam Aggrwal
P1020 is another member of QorIQ series of processors which falls in ULE category. It is an e500 based dual core SOC. Being a scaled down version of P2020 it has following differences: - 533MHz - 800MHz core frequency. - 256Kbyte L2 cache - Ethernet controllers with classification capabilities. Also the SOC is pin compatible with P2020 Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Add support for P2020RDB boardPoonam Aggrwal
The code base adds P1 & P2 RDB platforms support. The folder and file names can cater to future SOCs of P1/P2 family. P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series. Tested following on P2020RDB: 1. eTSECs 2. DDR, NAND, NOR, I2C. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-288xxx: Removed CONFIG_NUM_CPUS from 85xx/86xxPoonam Aggrwal
The number of CPUs are getting detected dynamically by checking the processor SVR value. Also removed CONFIG_NUM_CPUS references from all the platforms with 85xx/86xx processors. This can help to use the same u-boot image across the platforms. Also revamped and corrected few Freescale Copyright messages. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-288xxx: Refactored common cpu specific code for 85xx/86xx into one file.Poonam Aggrwal
Removed same code pieces from cpu/mpc85xx/cpu.c and cpu/mpc86xx/cpu.c and moved to cpu/mpc8xxx/cpu.c(new file) Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28stx: create common vendor/board hierarchy for STx boardsAlex Dubov
Move files belonging to the STx boards into common vendor directory and update the Makefile to reflect this. Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Remove unused CONFIG_CLEAR_LAW0 definesPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2886xx: Remove redudant PLATFORM_CPPFLAGSKumar Gala
For historic reasons we had defined some additional PLATFORM_CPPFLAGS like: PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1 PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1 However these are all captured in the config.h and thus redudant. Also moved common 86xx flags into cpu/mpc86xx/config.mk. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Remove redudant PLATFORM_CPPFLAGSKumar Gala
For historic reasons we had defined some additional PLATFORM_CPPFLAGS like: PLATFORM_CPPFLAGS += -DCONFIG_E500=1 PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1 However these are all captured in the config.h and thus redudant. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Add a 36-bit physical configuration for MPC8536DSKumar Gala
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary to allow for larger memory sizes. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-2885xx: Cleanup whitespace in mpc8536ds.cKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28pci/fsl_pci_init: Rework PCI ATMU setup to handle >4G of memoryKumar Gala
The old PCI ATMU setup code would just mimic the PCI regions into the ATMU registers. For simple memory maps in which all memory, MMIO, etc space fit into 4G this works ok. However there are issues with we have >4G of memory as we know can't access all of memory and we need to ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with anything since we can't turn it off. We first setup outbound windows based on what the board code setup in the pci regions for MMIO and IO access. Next we place PCICSRBAR below the MMIO window. After which we try to setup the inbound windows to map as much of memory as possible. On PCIe based controllers we are able to overmap the ATMU setup since RX & TX links are separate but report the proper amount of inbound address space to the region tracking to ensure there is no overlap. On PCI based controllers we use as many inbound windows as available to map as much of the memory as possible. Additionally we changed all the CCSR register access to use proper IO accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some 86xx platforms that didn't have it defined. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28pci/fsl_pci_init: Use PCIe capability to determine if controller is PCIeKumar Gala
Change the code to use the PCIe capabilities register to determine if we are a PCIe controller or not. Additionally cleaned up some white space and formatting in the file. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28pci/fsl_pci_init: Fold fsl_pci_setup_inbound_windows into fsl_pci_initKumar Gala
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows before it calls fsl_pci_init. There isn't any reason to just call it from fsl_pci_init and simplify things a bit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28pci/fsl_pci_init: Fold pci_setup_indirect into fsl_pci_initKumar Gala
Every platform that calls fsl_pci_init calls pci_setup_indirect before it calls fsl_pci_init. There isn't any reason to just call it from fsl_pci_init and simplify things a bit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28Use common code for Matrix Vision boardsAndré Schwarz
Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by using common code. Signed-off-by: André Schwarz <andre.schwarz@matrix-vision.de>
2009-08-28Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into nextWolfgang Denk
2009-08-26mpc83xx: mpc8349itx - accommodate larger kernel sizes & unzero the bootdelayKim Phillips
apparently the ITX was missed last round. Also make bootdelay consistent with other boards, so as to give on the opportunity to fix mistakenly set bootcmd without having checked for an bootdelay zero setting first. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-26mpc83xx: match dtb filename references to their dts equivalents in the linux ↵Kim Phillips
kernel Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-26NAND: DaVinci: V2 Adding 4 BIT ECC supportSandeep Paulraj
This patch adds 4 BIT ECC support in the DaVinci NAND driver. Tested on both the DM355 and DM365. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRSTSandeep Paulraj
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND chips. This ECC mode is similar to NAND_ECC_HW, with the exception of read_page API that first reads the OOB area, reads the data in chunks, feeds the ECC from OOB area to the ECC hw engine and perform any correction on the data as per the ECC status reported by the engine. This patch has been accepted by Andrew Morton and can be found at http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26mxc_nand: add nand driver for MX2/MX3Ilya Yanok
Driver for NFC NAND controller found on Freescale's MX2 and MX3 processors. Ported from Linux. Tested only with i.MX27 but should works with other MX2 and MX3 processors too. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26NAND: ADD page Parameter to all read_page/read_page_raw API'sSandeep Paulraj
This patch adds a new "page" parameter to all NAND read_page/read_page_raw APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the page information to send the READOOB command and read the OOB area before the data area. This patch has been accepted by Andrew Morton and can be found at http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch WE would like this to become part of the u-boot GIT as well Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-25 14:30:39 +0000