summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-09-18ARM: uniphier: remove redundant pin-muxing for EA24 pin of sLD3 SoCMasahiro Yamada
This is enabled by default for all the supported boot modes. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18ARM: uniphier: select PINCTRL and SPL_PINCTRLMasahiro Yamada
Now all UniPhier SoCs support a pinctrl driver. Select (SPL_)PINCTRL since it is mandatory even for base use. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18ARM: dts: uniphier: add pinctrl device node and pinctrl propertiesMasahiro Yamada
DT-side updates to make pinctrl on sLD3 SoC really available. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18pinctrl: uniphier: add UniPhier sLD3 pinctrl driverMasahiro Yamada
Add pin-mux support for UniPhier sLD3 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18pinctrl: uniphier: support 4bit-width pin-mux register capabilityMasahiro Yamada
On LD4 SoC or later, the pin-mux registers are 8bit wide, while 4bit wide on sLD3 SoC. Support it for the sLD3 pinctrl driver. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-17ARM: uniphier: introduce flags to adjust DRAM timing for LD20/LD21Masahiro Yamada
Unfortunately, this SoC needs per-board adjustment between clock and address/command lines. This flag will be passed to the DRAM init function and used for compensating the difference of DRAM timing parameters. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-17ARM: uniphier: fix DRAM size of LD21 SoC packageMasahiro Yamada
The channel 0 DRAM size of LD21 is half of that of LD20. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: merge board init functions into board_init()Masahiro Yamada
Currently, the UniPhier platform calls several init functions in the following order: [1] spl_board_init() [2] board_early_init_f() [3] board_init() [4] board_early_init_r() [5] board_late_init() The serial console is not ready at the point of [2], so we want to avoid using [2] from the view point of debuggability. Fortunately, all of the initialization in [2] can be delayed until [3]. I see no good reason to split into [3] and [4]. So, merge [2] through [4]. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: use checkboard() instead of misc_init_f()Masahiro Yamada
We can use checkboard() stub to show additional board information, so misc_init_f() should not be used for this purpose. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: remove IECTRL setup code of LD4 SoCMasahiro Yamada
This should be handled by the pinctrl driver. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14pinctrl: uniphier: move register base macros from header to .c fileMasahiro Yamada
These macros are only referenced in pinctrl-uniphier-core.c, so they need not reside in a header file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14pinctrl: uniphier: add System Bus pin-mux settingsMasahiro Yamada
This is needed to get access to UniPhier System Bus (external bus). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14mmc: uniphier-sd: migrate to CONFIG_BLKMasahiro Yamada
This is the state-of-the-art MMC driver implementation. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-14ARM: uniphier: enable Generic EHCI driver for Pro4 SoCMasahiro Yamada
This SoC is equipped with two EHCI cores and two xHCI cores. Enable the generic EHCI driver for the former. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14ARM: uniphier: delete unnecessary xHCI pin-mux settingsMasahiro Yamada
These ad-hoc pinmux settings were used for the legacy xHCI driver, which has gone now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14usb: uniphier: remove UniPhier xHCI driver and select DM_USBMasahiro Yamada
This driver has not been converted to Driver Model, and it is an obstacle to migrate other block device drivers. Remove it for now. The UniPhier SoCs already use a DM-based EHCI driver, so now ARCH_UNIPHIER can select DM_USB. These two changes must be done atomically because removing the legacy driver causes a build error. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
2016-09-14ARM: uniphier: sort select:s alphabeticallyMasahiro Yamada
ARCH_UNIPHIER is having more and more select:s. Sort them in case a select is accidentally duplicated. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-12Prepare v2016.09Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-12sf: fix sf probeCyrille Pitchen
This patch fixes the "sf probe" command. The very first SPI flash probe passes, for instance when u-boot tries to read its environment settings from a (Q)SPI memory but next "sf probe" commands fail because the flash memory node is unbound from the SPI controller children nodes. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-09common, kconfig: move VERSION_VARIABLE to KconfigHeiko Schocher
move VERSION_VARIABLE from board config file into a Kconfig option. Signed-off-by: Heiko Schocher <hs@denx.de>
2016-09-09Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2016-09-09cmd: Rework disk.c usageTom Rini
We only need the function found in cmd/disk.c when we have IDE, SCSI or USB_STORAGE enabled. While the first two are easy to get right, in the 3rd case we assume that the set of cases where we do have USB and do not enable USB_STORAGE are small enough that we can take the small bloat of un-discarded strings on gcc prior to 6.x Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09configs: Migrate CONFIG_USB_STORAGETom Rini
In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09net: asix: Fix AX88772B when used with DriverModelJoshua Scott
A previous patch (net: asix: fix operation without eeprom) added a two-byte shift to the packet buffer when receiving a packet on the AX88772B. This shift was not included when the driver was updated to work with DriverModel. Testing on a Marvell DB-88F6820-ACM showed that the adapter was not functioning correctly (EHCI timeouts). This patch brings the two-byte shift to the DriverModel implementation of ops->recv (asix_eth_recv). Testing on the same board, we were able to TFTP a file over and confirm that the crc32 was correct. Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-09Revert "net: nfs: Correct the reply data buffer size"Joe Hershberger
This reverts commit 6279b49e6c2fdaf8665355d1777bc90cd41fcf90. This caused a bad data crc. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Guillaume GARDET <guillaume.gardet@free.fr>
2016-09-09Revert "net: nfs: Use the tx buffer to construct rpc msgs"Joe Hershberger
This reverts commit 998372b4798fd7ebb666f571950df925b8d80f69. This caused a data abort on some platform. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reported-by: Guillaume GARDET <guillaume.gardet@free.fr>
2016-09-09configs: Resync with savedefconfigTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-09Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-09-07board: ks2: README: Update to add K2G supportLokesh Vutla
Update the README to add support for K2G EVM. Also - Add steps on how to use MMC boot - Fix load address when using CCS - Update build target to u-boot.bin from u-boot-dtb.bin as all ks2 platforms uses DT. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07efi_loader: provide efi_mem_desc versionMian Yousaf Kaukab
Provide version of struct efi_mem_desc in efi_get_memory_map(). EFI_BOOT_SERVICES.GetMemoryMap() in UEFI specification v2.6 defines memory descriptor version to 1. Linux kernel also expects descriptor version to be 1 and prints following warning during boot if its not: Unexpected EFI_MEMORY_DESCRIPTOR version 0 Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@gmail.com>
2016-09-07image-fit: switch ENOLINK to ENOENTJonathan Gray
ENOLINK is not required by POSIX and does not exist on OpenBSD and likely other systems. Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
2016-09-07compiler.h: use system endian macros on OpenBSDJonathan Gray
The u-boot endian macros map directly to system endian macros on OpenBSD. Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
2016-09-07board: am57xx: Fix missing check for beagle_x15Nishanth Menon
When beagleboard-X15 is booted, we see the following log: Unidentified board claims BBRDX15_ in eeprom header This is because of the missing check for x15 (the default) and reports an error for a valid board configuration. Fix the same. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07board: am57xx: MAINTAINERS: Update for current maintainerNishanth Menon
Felipe Balbi has move on from TI and the current email ID is no longer valid. So, replacing with Lokesh. While at it, update missing config file which was untracked. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-07global_data.h: Standardize tabs and alignment for commentsRobert P. J. Day
Line up comments for readibility. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-09-07pxe: Modify README to add the description about FIT imageWenbin Song
Use environment variable "kernel_addr_r" to indicate the location in RAM where FIT image will be stored. Use label command "kernel" to indicate which <path> the FIT image at. Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
2016-09-07pxe: Fix pxe boot with FIT imageYork Sun
When FIT image is used, a single image provides kernel, device tree and optionally ramdisk. Argc and argv need to be adjusted to support this. Test cases: 1. Booting with legacy images 2. Booting with legacy images without initrd 3. Booting with FIT image Test commands: 1. pxe get && pxe boot 2. sysboot Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
2016-09-07common/Kconfig: Fix various innocuous typos.Robert P. J. Day
Correct a small number of spelling mistakes. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-09-07omap3_pandora: Only set bootargs if distro_bootcmd failed to load.Vagrant Cascadian
As bootargs is hard-coded for the default behavior on the omap3_pandora, only set the bootargs if distro_bootcmd fails to load. This leaves distro_bootcmd free to use alternate boot arguments. Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
2016-09-07omap3_pandora: Switch to use config_distro_bootcmd.Vagrant Cascadian
Add support for using distro_bootcmd to the omap3_pandora target, falling back to prior behavior. Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
2016-09-07ARM: am335x: select DM_GPIOMasahiro Yamada
We are supposed to not add config entries with only "default y" in board/SoC Kconfig files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2016-09-07Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROLMasahiro Yamada
If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently not enough. Increase the default to 0x2000 for the case. This will be helpful for shorter defconfigs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-07ARM: armv7: move ARMV7_PSCI_NR_CPUS to KconfigMasahiro Yamada
Move this option to Kconfig and set its default value to 4; this increases the number of supported CPUs for some boards. It consumes 1KB memory per CPU for PSCI stack, but it should not be a big deal, given the amount of memory used for the modern OSes. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: armv7: move CONFIG_ARMV7_PSCI to KconfigMasahiro Yamada
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms can select. Then, move CONFIG_ARMV7_PSCI, which is automatically enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: armv7: guard memory reserve for PSCI with #ifdef CONFIG_ARMV7_PSCIMasahiro Yamada
If CONFIG_ARMV7_NONSEC is enabled, the linker script requires CONFIG_ARMV7_PSCI_NR_CPUS regardless of CONFIG_ARMV7_PSCI. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07ARM: tegra: remove wrong dependency on SPL_BUILDMasahiro Yamada
SPL_BUILD is not a CONFIG in Kconfig, so !SPL_BUILD is always true. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-06omap3_pandora: Switch to using "load" command to load the autoboot script.Vagrant Cascadian
CONFIG_CMD_FS_GENERIC is enabled; use it to load the autoboot script, rather than first attempting with fatload and falling back to ext2load. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Grazvydas Ignotas <notasas@gmail.com>
2016-09-06omap3_pandora: Fix mmc loading of autoboot script to use correct syntax.Vagrant Cascadian
fatload/ext2load both require that the device and partition be specified after specifying the device type. Specify the first partition on mmc device 0, which is the only mmc device currently configured on the pandora. Signed-off-by: Vagrant Cascadian <vagrant@debian.org> Acked-by: Grazvydas Ignotas <notasas@gmail.com>
2016-09-06TI: Rework SRAM definitions and maximumsTom Rini
On all TI platforms the ROM defines a "downloaded image" area at or near the start of SRAM which is followed by a reserved area. As it is at best bad form and at worst possibly harmful in corner cases to write in this reserved area, we stop doing that by adding in the define NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this. At current we define the end of scratch space at 0x228 bytes past the start of scratch space this this gives us a lot of room to grow. As these scratch uses are non-optional today, all targets are modified to respect this boundary. Tested on OMAP4 Pandaboard, OMAP3 Beagle xM Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: "B, Ravi" <ravibabu@ti.com> Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: "Kipisz, Steven" <s-kipisz2@ti.com> Cc: Daniel Allred <d-allred@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
2016-09-06omap3logic: Fix PBIAS BugAdam Ford
The PBIAS fixing is done in the MMC driver, and doing it in the the board file conflicts with the driver causing intermittent hangs on reboot. Remove this from the board file and let the driver do it. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2024-12-29 14:13:25 +0000