summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-14arm64: zynqmp: Do not assing MIO34 that early on zcu100Michal Simek
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in psu_init() and this pin is assigned to PMU but PMU configuration is not loaded yet. PMU gpio output is high that means board is powered off immediately. The patch is fixing this sequence that MIO34 stays assing to ps gpio IP. PMU config is loaded in SPL and then pin assigned to PMU through psu_post_config_data(). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Add support for OF_SEPARATE with board DTBMichal Simek
OF_BOARD and OF_SEPARATE can use board specific board_fdt_blob_setup(). OF_BOARD option is mostly used for picking up DTB from certain location. OF_SEPARATE option is used when DTB is appended after u-boot binary. This board specific function is aligned with current version in lib/fdtdec.c with checking CONFIG_XILINX_OF_BOARD_DTB_ADDR address first. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Rename fw_dtb variable to fdt_blobMichal Simek
The reason for this change is just get in sync with board_fdt_blob_setup() available at lib/fdtdec.c. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: Enable INIT_SP_RELATIVE by default when POC is enabledMichal Simek
When position-independent pre-relocation code is enable there is also necessary to enable relative early stack pointer not to use origin location pointed by CONFIG_SYS_INIT_SP_ADDR macro. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Do not call bss init and board_init_r from board_init_fMichal Simek
There is no reason to clear bss and call board_init_r() from board_init_f() beca it can be called directly from crt0_64.S with also support for SPL stack relocation to SDRAM. For more information please take a look at arch/arm/lib/crt0_64.S Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14spl: atf: Add missing ndepth initializationMichal Simek
ndepth needs to be initialized before it is used in fdt_next_node(). Uninitialized value is causing that node is found and depth increase but won't pass condition below because initial state wasn't setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14board: xilinx: Add support for user configurable boot script offsetT Karthik Reddy
Currently "script_offset_f" env variable is hardcoded, this variable specifies from which offset of the flash boot.scr should be read/write. As flashes are of different sizes having a fixed offset makes it difficult to load other images into the flash which may overwrite the boot script or cannot utilize the full memory. This current fix creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the offset address, overwrites the "script_offset_f" variable. Also removed existing variable with default values, as the default values are held by CONFIG_BOOT_SCRIPT_OFFSET Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: zynqmp: Fix emmc boot mode boot_target sequenceT Karthik Reddy
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp. Detect mmc alias at run time for setting up proper boot_targets sequence instead of setting boot_targets manually. Removed setting "modeboot" variable as it not longer need as we switched to distro boot. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14arm64: versal: Fix emmc boot mode boot_target issueT Karthik Reddy
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using the dev seq number from the sdhci@f1050000 controller. Dev seq number is setup based on DT aliases that's why needs to be setup at run time. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14mtd: nand: Remove hardcoded base address of nandAshok Reddy Soma
Remove hardcoded base address of nand and replace it with the value taken from device tree. Remove base address from header file too. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14mtd: nand: Move arasan nand driver to driver modelAshok Reddy Soma
Make changes to arasan nand driver to move it to driver model. Select DM_MTD if arasan nand driver is selected. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-11travis: Switch to QEMU v4.2.0 globallyTom Rini
Given our tests in GitLab / Azure we can use QEMU v4.2.0 for all platforms now. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-10gitlab/azure: Update to latest containerTom Rini
- Updated base snapshot - QEMU v4.2.0 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-10Merge branch '2020-01-10-master-imports'Tom Rini
- Android image support enhancements - Assorted ARM fixes and enhancements - m68k update
2020-01-10cmd: adtimg: Refactor usage styleEugeniu Rosca
Trying to extend 'adtimg' functionality [1], we've been severely hit by a major limitation in the command's usage scheme. Specifically, the command's user interface appears to be too centric to getting the DTB/DTBO entry [3] based on the index of the desired DT in the image, which makes it really difficult retrieving the DT entry based on alternative criteria (e.g. filtering by id/rev fields), the latter being demanded by real life customer use-cases [1]. This went to the point of receiving below feedback from Sam [2]: -- snip -- As for 'dtimg' command: after giving it some thought, I think not much people using it yet. So in this particular case I don't have some strong preference, and if you think the 'dtimg' interface is ugly, and it overcomes "don't break interfaces" rule, maybe now is a good time to rework it (before it gets widely used). -- snip -- Given the above, rework the usage pattern from [4] to [5], in order to allow an intuitive enablement of "by id|rev" DT search [6]. [1] https://patchwork.ozlabs.org/cover/1202575/ ("cmd: dtimg: Enhance with --id and --rev options (take #1)") [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 [3] https://source.android.com/devices/architecture/dto/partitions [4] Old usage adtimg dump <addr> - Print image contents adtimg start <addr> <index> <varname> - Get DT address by index adtimg size <addr> <index> <varname> - Get DT size by index [5] New usage adtimg addr <addr> - Set image location to <addr> adtimg dump - Print out image contents adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] - Get DT address/size/index by id|rev fields Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2020-01-10cmd: adtimg: Rename internal symbolsEugeniu Rosca
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming consistency in the internal implementation of 'adtimg.c'. No functional change intended. Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-01-10dtimg/am57xx_evm_defconfig: Rename dtimg to adtimgEugeniu Rosca
Rename the existing 'dtimg' command to 'adtimg', in order to: - Suggest the Android origins and scope - Be consistent with the upcoming 'abootimg' command (naming suggested by Simon [*]) The change in _not_ backward compatible, but its benefits outweigh its downsides, given that we don't expect active users of 'dtimg' today. Perform the rename in several steps: 1. Rename *.c file and Kconfig symbol. This should allow 'git log --follow' to properly track the history of 'adtimg.c' 2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c' ELF comparison [**] before and after shows no functional change. [*] https://patchwork.ozlabs.org/patch/1182212/#2291600 [**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o) Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Glass<sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2020-01-10virtio: fix typo devicdHeinrich Schuchardt
%s/devicd/device Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-01-10arm: cpu: armv8: add support for arm psci reset2.Rajesh Ravi
Current U-Boot has only support for psci reset. Adding support for arm psci reset2 allows passing of reset level and other platform sepcific parameters like strap settings to lowlevel psci implementation. Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
2020-01-10arch: arm: Program GIC LPI configuration tableBharat Kumar Reddy Gooty
Programs the following: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com> Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
2020-01-10mkimage: simplify fit_check_params()Heinrich Schuchardt
fit_check_params() wants at least two of dflag, fflag, and lflag set. Simplify the logical constraint checking this. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-01-10cmd/eeprom.c: prepend 0x to hex numbers in output message formatKlaus H. Sorensen
If the numbers do not happen to contain any digits from [a-f], it's not clear that they are base 16. Signed-off-by: Klaus H. Sorensen <khso@prevas.dk> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
2020-01-10test/cmd_ut.c: fix cmd_ut_categoryPhilippe Reynes
In the function cmd_ut_category, the prefix is used with the function strncmp to know if the prefix should be removed from the test name, even if the prefix is NULL. To avoid this issue, we consider that a prefix NULL mean no prefix. So we only try to remove the prefix from the test_name if the prefix is not NULL, then we avoid to call the function strncmp with a NULL prefix. Reported-by: Coverity CID 281110 Fixes: 4ad4edfe ("cmd_ut: add a parameter prefix to the function cmd_ut_category") Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-01-10gcc-9: silence 'address-of-packed-member' warningAndy Shevchenko
GCC 9.x starts complaining about potential misalignment of the pointer to the array (in this case alignment=2) in the packed (alignment=1) structures. Repeating Linus' Torvalds commit 6f303d60534c in the Linux kernel. Original commit message: We already did this for clang, but now gcc has that warning too. Yes, yes, the address may be unaligned. And that's kind of the point. This in particular hides the warnings like drivers/usb/gadget/composite.c:545:23: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 545 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:550:24: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 550 | collect_langs(sp, s->wData); drivers/usb/gadget/composite.c:555:25: warning: taking address of packed member of ‘struct usb_string_descriptor’ may result in an unaligned pointer value [-Waddress-of-packed-member] 555 | collect_langs(sp, s->wData); Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-10boards/km_arm: enable support for Macronix SPI NOR flashHolger Brunck
The M25P80 and M25P32 SPI flashes from Numonix/Micron will be replaced by Marconix MX25L80 and MX25L32 flashes. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10arm/km: remove board KMCOGE3UNHolger Brunck
This target is out of maintenance and can be removed. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10km/boards: add MAC address offset as argument to ivm_populate_envHolger Brunck
For upcoming SECU board we have different MAC address offsets depending on which functional unit we are running. In this case we need to pass this value to the ivm_populate_env function instead of using the hard coded config option there. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10km/boards: fix typo for MAC address offset config optionHolger Brunck
This patch only fixes a typo. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> CC: Stefan Roese <sr@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-01-10poweroff: add poweroff for mt6323 pmicFrank Wunderlich
this adds poweroff to bananapi r2 / mt7623 / mt6323 pmic Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-01-10rtc: add support for DS3232 deviceHan Nandor
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM. Add an RTC driver for DS3232 device, which provides time and date support. Also read and write functions are provided, which can be used to access the SRAM memory. Signed-off-by: Nandor Han <nandor.han@vaisala.com>
2020-01-10spl: fix stack usage check if gd is not initializedSimon Goldschmidt
Most platforms do not set up gd->start_addr_sp in SPL. Since this is required for CONFIG_SPL_SYS_REPORT_SACK_F_USAGE to work correctly, set up gd->start_addr_sp in SPL to the value passed to board_init_f_init_reserve if it is not set yet. Fixes: d8c0332031 ("spl: implement stack usage check") Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-01-10m68k: Drop CONFIG_MCFPIT supportTom Rini
All platforms currently use the "MCFTMR" DMA timer rather than the PIT timer, so drop the MCFPIT code. Cc: Huan Wang <alison.wang@nxp.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com> Cc: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Angelo Dureghello <angelo@sysam.it>
2020-01-10bootcount: add a DM i2c eeprom backing store for bootcountRobert Beckett
This driver allows the use of i2c eeprom device or partition as backing store for boot counter values with DM enabled. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-10drivers: mcfmii: add dm supportAngelo Durgehello
Add specific dm code, but maintaining this driver as is, so more in the shape of a mii library. Can be moved to dm in a further step. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: fsl_mcdmafec: conversion to dmAngelo Durgehello
Full conversion to dm for all boards, legacy code removed. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: mcffec: conversion to dmAngelo Durgehello
Full conversion to dm for all boards, legacy code removed. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: net: add mcf fec dm Kconfig supportAngelo Durgehello
Add ColdFire fec to Kconfig. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10m68k: add dm fec supportAngelo Durgehello
Add architecture-related code for dm fec support. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10configs: purge unneeded fec definesAngelo Durgehello
Remove unneeded fec-related defines after fec moved as dm. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10configs: add eth dm support for all ColdFire boardsAngelo Durgehello
Add dm eth config options for all involved ColdFire-based boards. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10m68k: add fec fdt overrides to all boardsAngelo Durgehello
Add ethernet controller overrides for all involved boards. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10m68k: add fec base node to devicetreesAngelo Durgehello
Add basic ethernet controller devicetree nodes for all ColdFire families. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-09Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-mpc83xxTom Rini
- A small PR with MC8309 fixes from Rasmus.
2020-01-09Merge tag 'dm-pull-8jan20' of git://git.denx.de/u-boot-dmTom Rini
dm: Increased separation of ofdata_to_platdata() and probe methods
2020-01-09Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- DFU updates
2020-01-08Merge tag 'efi-2020-04-rc1' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc1 This pull request provides: * support for FIT images for UEFI binaries * drivers for hardware random number generators * an implementation of the EFI_RNG_PROTOCOL * a sub-command for efidebug to display configuration tables
2020-01-08Merge tag 'uniphier-v2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier UniPhier SoC updates for v2020.04 - add pinmux nodes for I2C ch5, ch6 - enable SPI driver and command
2020-01-08Merge tag 'u-boot-imx-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx --------------------------------------------------------------------- Add i.MX8MP SoC and EVK board Update README for i.MX8MN EVK and fix mmc env Add pca9450 driver -------------------------------------------------------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/634211885
2020-01-08Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2020-01-08Merge tag 'u-boot-amlogic-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Khadas VIM3L based on Amlogic S905D3 support - Various fixups for amlogic boards - Unnecessary header includes drop into video/meson
generated by cgit (git 2.34.1) at 2025-01-04 07:24:17 +0000