| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Just extend tables with this new device.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
When ARCH_DMA_MINALIGN is greater than header size of the bit file, and buf is
not aligned, new_buf address became greater then buf_start address and the
load_word loop corrupts bit file data.
A work around is to decrease new_buf of ARCH_DMA_MINALIGN, it might corrupt data
before buf but permits to load correctly.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch fix the u-boot shell problem on TRATS2 board.
- If hold the key while booting is in progress,
white spaces are written in u-boot shell.
Set Automatically clears after resetting Rx FIFO.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Because of the list of peripherals is not sequential,
such a routine does not check for valid correctly.
Error check will be done when call the exynos_pinmux_config function.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
|
|
The value of PERIPH_ID_COUNT was wrong, and unnecessary.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Rajehswari Shinde <rajeshwari.s@samsung.com>
|
|
describe a set of default features that distros can rely on being available.
having this common definition means that distros can easily support systems
implementing them.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
|
|
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
|
|
|
|
|
|
|
|
|
|
|
|
People who write (or scripts that auto-generate) extlinux.conf don't
want to know about HW-specific information such as FDT filenames. Create
a new extlinux.conf tag "fdtdir" that specifies only the directory where
FDT files are located, and defer all knowledge of the filename to U-Boot.
The algorithm implemented is:
==========
if $fdt_addr_r is set:
if "fdt" tag was specified in extlinux.conf:
load the FDT from the filename in the tag
else if "fdtdir" tag was specified in extlinux.conf:
if "fdtfile" is set in the environment:
load the FDT from filename in "$fdtfile"
else:
load the FDT from some automatically generated filename
if no FDT file was loaded, and $fdtaddr is set:
# This indicates an FDT packaged with firmware
use the FDT at $fdtaddr
==========
A small part of an example /boot/extlinux.conf might be:
==========
LABEL primary
LINUX zImage
FDTDIR ./
LABEL failsafe
LINUX bkp/zImage
FDTDIR bkp/
==========
... with /boot/tegra20-seaboard.dtb or /boot/bkp/tegra20-seaboard.dtb
being loaded by the sysboot/pxe code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The specification for extlinux.conf[1] states that "fdt" is an alias for
"devicetree". To date, U-Boot only implements "fdt". Rectify that.
[1] http://freedesktop.org/wiki/Specifications/BootLoaderSpec/
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Just to be sure that there is no pending data.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It speeds up writing a lot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Just list one more exception.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
It is nice to see u-boot version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Command provides just dump subcommand for showing clock
frequencies in a soc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Fix the timeout issue after running "bootp" command in U-Boot console.
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.
This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These are fairly complete, and near-clones of Tegra114 Venice, with an
additional I2C port, and MMC address changes for Tegra124.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These files are used by both SPL and main U-Boot.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These files are for code that runs on the CPU (A15) on Tegra124 boards.
At this time, there is no A15-specific code here. The warmboot/LP0 files
aren't included as that code hasn't been ported yet.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This provides SPL support for Tegra124 boards - AVP early init, plus
CPU (A15) init/jump to main U-Boot.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These headers define the Tegra124 hardware. Add them to the usual
place.
Add Tegra124 chip ID/SKU ID definitions to common headers.
There's no real HW change on Tegra124 for 90% of the toys, so it might
make sense for a future patch to unify some of the content of these
files in a common location.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The reg property for node spi@7000d800 was wrong. Fix it to match the
HW. This change was verified against the Linux kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
__pinmux_nand() won't compile if PERIPH_ID_NDFLASH isn't defined.
Prevent this from causing build problems on newer SoCs without NAND
support (or without SW support for NAND yet), but preventing
compilation unless the function will actually be used, i.e. when
CONFIG_TEGRA_NAND is defined.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, rewrote commit description, moved ifdef around whole function
rather than just body]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
There's already an SoC-specific conditional in cpu.h to determine the
PLLP rate. Define the CSITE clock rate inside the same conditional, so
that we can remove a conditional from clock_enable_coresight(). This
means one less place to update the code for new SoCs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This programming sequence is correct per Jimmy Zhang, and makes sense
too!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.
Consequently, we can remove the mask definitions from pmc.h.
Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Use a named constant for the PLL lock bit in enable_cpu_clocks().
Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.
The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured
Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.
The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.
There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Since all code that sets or interprets MASK_BITS_* now uses the enums
to define/compare the values, there is no need for MASK_BITS_* to have
a specific integer value. In fact, having a specific integer value may
encourage people to hard-code those values, or interpret the values in
incorrect ways.
As such, remove the logic that assigns a specific value to the enum
values in order to make it completely clear that it's just an enum, not
something that directly represents some integer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Not all code that set or interpreted "mux_bits" was using the named
macros, but rather some was simply using hard-coded integer constants.
This makes it hard to determine which pieces of code are affected by
changes to those constants.
Replace the integer constants with the equivalent macro definitions so
that everything is nicely tied together.
Note that I'm not convinced all the code was using the correct integer
constants, and hence I'm not convinced that all the code is now using
the desired macros. However, this change is a purely mechanical
replacement and should have no functional change. Fixing any bugs will
come later, separately.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
