summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-02-22OMAP3: Pandora: Update pin muxDirk Behme
Clock pin must have input enabled for MMC3 to work. Also enable pull-ups for cmd/data lines to be consistent with remaining MMC host pin setup. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2009-02-22OMAP3: Add OMAP3 auto detectionDirk Behme
This patch adds OMAP3 cpu type auto detection based on OMAP3 register and removes hardcoded values. Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22OMAP3: Beagle: Add board revision detectionDirk Behme
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX) which might need different software handling. For this, GPIO pin 171 (GPIO module 6, offset 11) can be used to check for board revision. If this pin is low, we have a rev C board. Else it must be a revision Ax or Bx board. To handle board differences you can call function beagle_get_revision(). E.g.: if (beagle_get_revision()) { /* do special revision C stuff here */ } Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22OMAP3: Overo: Clean up pin mux and GPIO configurationDirk Behme
* Make Overo GPIO114 an input for touchscreen PENDOWN * Make Overo GPIO144-147 readable * Make Overo EHCI pinmux match beagle rev c setup * Adjust pinmux for SMSC911X network chip support * Remove unnecessary GPIO setup * Fix merge error in Makefile Signed-off-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22nmdk8815: fix onenand supportJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22nomadik/nand: fix 'ecc512' discards qualifiers from pointer target typeJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22davinci: fix implicit declaration of function 'davinci_errata_workarounds'Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22arm: add uart dcc supportJean-Christophe PLAGNIOL-VILLARD
Serial driver via the EmbeddedICE macrocell's DCC channel using co-processor 14. It does include a timeout to ensure that the system does not totally freeze when there is nothing connected to read. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22ARM DaVinci: Add common peripherals and modules enable functions.Hugo Villeneuve
Taken all the duplicated code for enabling common modules and apply software workarounds from the board specific code into common functions. Also added comments explaining the workarounds (from TI errata documents) and replaced some numerical bit numbers with more meaningful defines. Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
2009-02-22Enable Ethernet for Nomadik 8815 Evaluation KitAlessandro Rubini
This trivially enables Ethernet support in the debug board by setting up the proper chip select. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22Nand driver for Nomadik SoCAlessandro Rubini
This driver implements the ECC algorithm described in the CPU data sheet and uses the OOB layout chosen in already-released development systems (shipped with a custom-made u-boot 1.3.1). Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22Added nomadik.h headerAlessandro Rubini
Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22Coding Style cleanup; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22Makefile: fix cleanupWolfgang Denk
Commit e4943ec5 moved the ARM boards to a vendor directory but forgot to adapt the cleanup rules in the Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-21Cleanup the comment for m68k linux boot argument passing.Richard Retanubun
This patch clarifies the way m68k passes linux boot argument. The one gotcha here is that the assembly instruction that the compiler uses to jump to the kernel is 'jsr' which pushes the program counter for the instruction after the jsr into the stack pointer. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-21sh: Fix rsk7203 in tree buildPeter Griffin
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
2009-02-21bootm: Reduce the unnecessary memmoveMinkyu Kang
Although load address and image start address are same address, bootm command always does memmove. That is unnecessary memmove and can be taken few milliseconds (about 500 msec to 1000 msec). If skip this memmove, we can reduce the boot time. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-02-21fpga: Fix Spartan III FPGA bootingMatthias Fuchs
This patch does some minor fixing of the Xilinx Spartan III FPGA boot code: - Fixed call order of post configuration callback and success message printing (result of copy-paste?) - remove obsolete comment - minor coding style cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2009-02-21fpga: Fix Spartan II FPGA bootingMatthias Fuchs
This patch does some minor fixing of the Xilinx Spartan II FPGA boot code: - Fixed call order of post configuration callback and success message printing (result of copy-paste?) - relocate post configuration callback only when it is implemented - remove obsolete comment - minor coding style cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2009-02-21drivers/serial/ns16550: move ifdef into Makefile COBJS-$(...)Mike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-21lcd_putc bug fix for tab.Derek Ou
Signed-off-by: Derek Ou <dou@siconix.com>
2009-02-21MIPS: cpu/mips/Makefile: Add a missing START lineShinya Kuribayashi
In the commit 79b51ff8205f0354d5300570614c1d2db499679c ([MIPS] cpu/mips/ Makefile: Split [CS]OBJS onto separate lines), I wrongly deleted a START line. This patch puts it back. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
2009-02-21Enable ext2 support for TQM8xxL/M based boardsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-20ARM:PXA Use new definitions in mmc.hTom Rix
Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20Reduce the scope of PXA's mmc_read/mmc_write/mmc_bread functionsAndy Fleming
These names are being taken over by the new MMC framework. Hopefuly the PXA can be easily ported, and these functions will go away entirely. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20pxa: move mmc drivers to drivers/mmcJean-Christophe PLAGNIOL-VILLARD
introduce new macro CONFIG_PXA_MMC to activate it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20ARM:PXA Remove redefinition of mmc_cid and mmc_csd.Tom Rix
These structures are defined in the common mmc.h This was compile checked on cerf250.
2009-02-20pxa: fixing get_timer to return time in miliseconds.Micha Kalfon
Fixing the get_timer function to return time in miliseconds instead of ticks. Also fixed PXA boards to use the conventional value of 1000 for CONFIG_SYS_HZ. Signed-off-by: Micha Kalfon <smichak.uv@gmail.com>
2009-02-19ARM:OMAP3 Change mmc_init to mmc_legacy_initTom Rix
omap3_mmc.c was changed to define mmc_legacy_init. Remove unused functions. Compile tested on all arm Runtime tested on Zoom1. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-02-1982xx, mgcoge: updates for 2009.03Heiko Schocher
- activate CS4 for accessing the FPGA - activate Rx buf len > 1 on SMC - pram activated - MTDPARTS_DEFAULT defined - update the size of the flashes in the DTS before booting Linux - MONITOR_LEN updated to 384k - added CONFIG_HOSTNAME - added CONFIG_ENV_BUFFER_PRINT - Environment size reduced to 16k Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-198xx, mgsuvd: updates for 2009.03Heiko Schocher
- activate Rx buf len > 1 on SMC - pram activated - MTDPARTS_DEFAULT defined - update the size of the flash in the DTS before booting Linux - MONITOR_LEN updated to 384k - added CONFIG_HOSTNAME - added CONFIG_ENV_BUFFER_PRINT - Environment size reduced to 16k Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19MMC: Don't use new framework code if not enabledDirk Behme
Don't use code of new MMC framework in cmd_mmc if CONFIG_GENERIC_MMC isn't enabled. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-19TQM8xxL: make some room in low memory for future needsWolfgang Denk
THe TQM8xxL use a ahnd-optimized linker script to efficiently use the small boot sectors in the flash. This patch makes some room in the first sector to prepare for a size increase of lib_generic/vsprintf.o by a future patch. Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-19README: remove duplicate entryKim Phillips
it's been around since the original commit (2ad6b513) that added two identical entries. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-19Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2009-02-19Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-02-19Coding style cleanup, update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-19sata_sil3114: fix compiler warningKim Phillips
judging from other printfs in the same file, it seems ata should be postpended with the interface number, not the address of the global port variable. Fixes this for current u-boot-mpc83xx tree: Configuring for MPC8349ITX board... sata_sil3114.c: In function 'sata_bus_softreset': sata_sil3114.c:99: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *' sata_sil3114.c:108: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *' Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-19Create configuration option for restricted ns16550 functionsRon Madrid
This patch will create a configuration option for a minimum configuration for the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new configuration option to the SIMPC8313.h config file in order to fix the NAND bootstrap build error. This option will exclude all functions with exception of NS16550_putc and NS16550_init. This will be used primarily to save space and remove unused code from builds in which space is limited. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
2009-02-19mkconfig: include board config.h before asm/config.hKim Phillips
swapping the include order suppresses warnings for board configs that define their own CONFIG_MAX_MEM_MAPPED: In file included from /home/r1aaha/git/u-boot/include/config.h:5, from /home/r1aaha/git/u-boot/include/common.h:35, from simpc8313.c:26: /home/r1aaha/git/u-boot/include/configs/SIMPC8313.h:81:1: warning: "CONFIG_MAX_MEM_MAPPED" redefined In file included from /home/r1aaha/git/u-boot/include/config.h:4, from /home/r1aaha/git/u-boot/include/common.h:35, from simpc8313.c:26: /home/r1aaha/git/u-boot/include/asm/config.h:28:1: warning: this is the location of the previous definition Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-18Fix build errors after making flash_get_info() non-staticWolfgang Denk
Fix for these build problems: error: static declaration of 'flash_get_info' follows non-static declaration Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-18ppc4xx: PCIe: Change 16GB inbound memory to 4GBStefan Roese
This patch fixes a problem recently seen on some 4xx platforms. For example on Kilauea PCIe slot #0. Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18ppc4xx: Some more PMC405 coding-style cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18ppc4xx: Update PMC405 board supportMatthias Fuchs
This patch prepares the good old PMC405 board support for upcoming PMC405V2 patches. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18ppc4xx: Cleanup PMC405 board supportMatthias Fuchs
This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18qong: changes to Dave/DENX Qong configurationIlya Yanok
1. Changes to the default environment: - "bootcmd" defined as "run flash_self" - "saveenv" command removed from "update" - "uboot" changed to "u-boot" (also in "load") - "addmtd" variable defined (and added to all boot commands) 2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command 3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined 4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem with truncated "bootargs" environment variable. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-02-18common/console: avoid ifdef CONFIG_CONSOLE_MUX when it's possibleJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-18common/console: coding style cleanupJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-18mpc8xx_pcmcia: move CONFIG_8xx out of .c file and into MakefileMike Frysinger
Move the CONFIG_8xx mpc8xx_pcmcia.c protection out of the C file and into the Makefile so we avoid pointless compiling of the file. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18disk: convert part_* files to COBJ-$(CONFIG_XXX) styleMike Frysinger
Move the CONFIG_XXX out of the part_XXX.c file and into Makefile to avoid pointless compiles. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit (git 2.34.1) at 2024-12-28 12:04:59 +0000