| Age | Commit message (Collapse) | Author |
|---|
|
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch rebase the stm32mp1 device tree source from
linux kernel v4.18-rc1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Use new API syscon_node_to_regmap in sysreset_syscon driver
for compatible "syscon-reboot"; that's avoid the need of explicit
syscon binding for "regmap" handle.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
For qemu-x86 the date command produces wrong days of the week:
Date: 2018-07-06 (Saturday) Time: 18:02:03
Date: 2018-07-07 (unknown day) Time: 21:02:06
According to a comment in the Linux driver the mc146818 only updates the
day of the week if the register value is non-zero.
Sunday is 1, saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf).
So let's use our library function to determine the day of the week.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Extend BOOTDELAY help text to cover its additional usage within the
bootmenu command.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
The test for (CONFIG_BOOTDELAY >= 0) has been in U-Boot since the
beginning, but the meaning of it has changed over time. Allow the
default to be set for any value, including -ve ones. This allows
(for example) CONFIG_ENV_IS_NOWHERE to have values for bootdelay in
its compiled in environment.
The only thing this changes is where the default for bootdelay can be
fetched from; before this change you get a compiled in default, after
you'll pull it from the default value in the environment, but both values
will be the same. Also if there's a value set in the environment then
that will take precedence (as before).
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
The comparison
logical > item->logical + item->length
in btrfs_map_logical_to_physical is wrong and should be instead
logical >= item->logical + item->length
For example, if
item->logical = 4096
item->length = 4096
and we are looking for logical = 8192, it is not part of item (item is
[4096, 8191]). But the comparison is false and we think we have found
the correct item, although we should be searing in the right subtree.
This fixes some bugs I encountered.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
|
|
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
RAW mode ARGS sector doesn't have to be used for all falcon boot. Skip
loading ARGS sectors if not defined.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This is needed for having access to the devices below this bus, most
important is uart and boot-device (spi, mmc, ...) in SPL stage.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
On other OS, not one provided by B&R, it is not guaranteed that there
are factory-settings within a devicetree. So we must not treat the
absence of them as error.
Further we've the fact that on different version of the device-tree
files there are different namings of the factory-settings, we consider
this with searching for an alternative name.
changing things as following:
- don't treat as error if the bootloader version cannot written into
devicetree.
- since the naming of the factory-settings are different in different
versions of the provided device-tree we search for the alternate name
"/fset"
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
If a board-code calls the pmicsetup(u32 mpupll) with a mpupll value
!= 0 it wants to force some frequency with the value provided by mpupll.
Setting up 1 GHz is wrong here.
Nobody did take notice about that yet, since every board calls this
function with zero.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This interface names may vary over different products, to consider this
fact we replace the interface label "IF1" and "IF2" on the summary
screen with some more generic wording "MAC1" and "MAC2".
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
Since we're going to drop LCD-support on brppt1 boards, we have to make
this stuff here optional and remove the #error path.
We also move out the ft_board_setup(...) from this #ifdef because
there's no relationship with the LCD-code and on the other hand this is
still needed in future even with LCD-support off.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
The linux systems running on the brppt1 targets are using modern DRM
drivers since long time ago. Further we are going to drop the LCD
support completely on this board, so the simple-framebuffer setup
becomes obsolete.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
Add basic smem sandbox testing.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add Sandbox driver for SMEM. mostly stub operations.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Added necessary nodes for Qualcomm smem driver.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Added necessary nodes for Qualcomm smem driver.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
EFI image handle and system table are not used in _relocate().
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
|
|
EFI image handle and system table are not used in _relocate().
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
|
|
EFI image handle and system table are not used in _relocate().
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
|
|
Current implementation of find_next_zero_bit() is incompatible with arm64.
Hence fix it by using BITS_PER_LONG define instead of constants and
use generic ffz() implementation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
Fix typos and update the supported devices for all Amlogic boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In case of phy are provided from a PHY provider nodes as following:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <1>;
};
};
and PHY are called as following:
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc_clk USBH>;
resets = <&rcc_rst USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
companion = <&usbh_ohci>;
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
If FIT image is used, CONFIG_SYS_FDT_BASE is not needed.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Add support of loading FIT image from NOR flash.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The function set_default_vars() in common.c adds H_INTERACTIVE to the
h_import() flag, but the function has no way of telling if the command
actually was user directed like this flag suggest. The flag should be
set by the calling function do_env_default() in nvedit.c instead, where
the command is certainty user directed.
Move the H_INTERACTIVE flag from set_default_vars() to do_env_default().
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The env_flag in do_env_default() doesn't get propagated and therefore
gets ignored by himport_r(). This breaks to ability to "forcibly" reset
variables to their default values using the environment command.
Scenario example of the problem:
# setenv kernel uImage
# setenv .flags kernel:so
# env default -f kernel
## Error: Can't overwrite "kernel"
himport_r: can't insert "kernel=zImage" into hash table
Change the call path so it will pass the flag correctly.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The naming convention for flags in nvedit.c is:
* The hashtable flag (defined in search.h) is named "env_flag"
* The command flag argument (defined in command.h) is named "flag"
This convention is kept in functions like do_env_print(), do_env_set()
and do_env_delete(), but not in do_env_default().
Rename the hashtable flag in do_env_default() from "flag" to "env_flag".
Rename the command flag in do_env_default() from "__flag" to "flag".
No functional change.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
When sourcing a FIT format script, if we've not been told the unit name
to use, look for a default property at the root of /images to work out
which unit we should use.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add ut_assertnull macro to include/test/ut.h
For testing of functions that returns NULL on errors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Xilinx changes for v2018.09
clk:
- Fix zynqmp clock driver
common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return macros in cmd_process_error
- Fix duplication of CONFIG_SYS_PROMPT_HUSH_PS2
- Support watchdog in usb_kbd.c
- Fix name usage in usb_kbd.c
- Support systems with non zero memory start initialized from DT only
gpio:
- Add support for manual relocation in uclass
- zynq - use live tree
- zynq - fix match data reading
- zynq - setup bank name
- xilinx - convert driver to DM
microblaze:
- Use generic iounmap/ioremap implementations
- Redesign reset logic with sysreset features
- Use watchdog and gpio over DM
- Remove unused macros and fix some checkpatch issues
- Fix timer initialization not to be called twice
serial:
- zynq - Use platdata intead of priv data
sysreset:
- Add support for manual relocation in uclass
- Add gpio-restart driver
- Add microblaze soft reset driver
watchdog:
- Add support for aliases in uclass
- Add support for manual relocation in uclass
- Convert xilinx driver to DM
- cadence - update info in the driver and not stop wdt in probe
xilinx:
- Enable LED gpio for some targets with gpio-leds DT node
- Setup variables via Kconfig
zynq:
- Add support for watchdog aliases
- Add support for mini nand/nor configurations
- Wire FPGA initalization in SPL
zynqmp:
- Enable mass storage for zcu100
- Handle external pmufw files
- Add support for secure images
- Some Kconfig movements and alignments
- Add support for watchdog aliases
- Use subcommands style for platform command
- Add mmio_read/write platform commands
- DT updates
- Add support for mini qspi configuration
|
|
commit 4aba5fb857c1 ("arm: zynq: Rework FPGA initialization")
moved FPGA initialization from board_init() to arch_early_init_r(),
which is not called as part of the SPL
Fix this by calling arch_early_init_r() in the spl_board_init()
function, so the FPGA is correctly initialized
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Disable the use of function zynq_loadfs when compiling
the driver for the SPL, as the following filesystem
functions are not found by the linker:
- fs_set_blk_dev
- fs_read
- fs_set_blk_dev
- fs_read
- fs_read
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
