summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2008-01-16drivers/net/rtl8139.c: Fix tx timeoutShinya Kuribayashi
"to = (currticks() + RTL_TIMEOUT)" has possibilities to wrap around. If it does, the condition "(currticks() < to)" becomes invalid and immediately leads to tx timeout error. This patch introduces the fine-graded udely(10) loops to ease the impact of wrapping around. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Masami Komiya <mkomiya@sonare.it> Cc: Lucas Jin <lucasjin@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16TSEC: Add the support for RealTek RTL8211B PHYDave Liu
Add the support of RealTek RTL8211B PHY, the RTL8211B PHY only supports RGMII and MII mode. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16Remove annoying debug printout for PHY less boards.Joakim Tjernlund
PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16net: reduce boot latency on QE UEC based boardsKim Phillips
actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16TSEC driver: Change MDIO support to allow access to any PHYs on the MDIO busmichael.firth@bt.com
The current TSEC driver limits MDIO access to the devices that have been configured as attached to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands. Signed-off-by: Michael Firth <michael.firth@bt.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-15QE UEC: Extend number of supported UECs to 4David Saada
This patch extends the number of supported UECs to 4. Note that the problem of QE thread resources exhaustion is resolved by setting the correct number of QE threads according to Ethernet type (GBE or FE). Signed-off-by: David Saada <david.saada@ecitele.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-14Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk
2008-01-14QE: fix compile warningDave Liu
qe.c: In function 'qe_upload_firmware': qe.c:390: warning: pointer targets in passing argument 2 uec.c: In function 'uec_initialize': uec.c:1236: warning: 'uec_info' may be used uninitialized Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-01-14ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bitStefan Roese
Now that bit 29 is the USB PHY reset bit, update the Kilauea port to remove the USB PHY reset after powerup. The CPLD will keep the USB PHY in reset (active low) until the bit is set to 1 in board_early_init_f(). Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-13ARM: update mach-types.h from 2.6.24-rc7 Linux kernel treeWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: Fix typo in ads5121.c, adjust default environmentWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121: MAX slew rate for PATA pinsJohn Rigby
Signed-off-by: John Rigby <jrigby@freescale.com>
2008-01-13Fix Makefile dependency problem with parallel builds.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8544DS: fix board Makefile for silent build (with -s)Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13PMC440 board: fix board Makefile for out-of-tree buildingWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Makalu: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/masterWolfgang Denk
2008-01-13cmd_nand : fix compiler warning.Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-01-13CFI: Fix CONFIG_FLASH_CFI_LEGACY compilationMichael Schwingen
Signed-off-by: Michael Schwingen <michael@schwingen.org> Acked-by: Stefan Roese <sr@denx.de>
2008-01-13Merge branch 'master' of /home/stefan/git/u-boot/u-bootStefan Roese
2008-01-13MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBESWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MPC8xx FEC driver: fix compiler warning.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13Fix Makefile dependencies issues; allow silent buildWolfgang Denk
- get rid of "version" target whichdidn't really work - make autoconf.mk depend on version_autogenerated.h to make sure to rebuild files as needed - add XECHO macro to allow for silent build using "make -s" Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13ADS5121e: fix compile warningWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13MUNICes: fix board Makefile for remote build directoryWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12MPC5200: don't use hardcoded MBAR address in Bestcomm firmwareOliver Weber
Signed-off-by: Oliver Weber <almoeli@gmx.de>
2008-01-12Make bootretry work when command line editing is enabledAndreas Engel
Currently, when CONFIG_CMDLINE_EDITING is set, bootretry doesn't work. This patch fixes the problem. Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-01-12Refactor code for "i2c sdram" commandLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-12Fix "i2c sdram" command for DDR2 DIMMsLarry Johnson
Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the "i2c sdram" command. This patch provides correct alternative interpretations when DDR2 memory is detected. Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-12Fix linker scripts: add NOLOAD atribute to .bss/.sbss sectionsWolfgang Denk
With recent toolchain versions, some boards would not build because or errors like this one (here for ocotea board when building with ELDK 4.2 beta): ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab] For many boards, the .bss section is big enough that it wraps around at the end of the address space (0xFFFFFFFF), so the problem will not be visible unless you use a 64 bit tool chain for development. On some boards however, changes to the code size (due to different optimizations) we bail out with section overlaps like above. The fix is to add the NOLOAD attribute to the .bss and .sbss sections, telling the linker that .bss does not consume any space in the image. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12USB: Add Philips 1561 PCI-OHCI idsTsiChung Liew
(needed for M5475EVB) Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2008-01-12Add MAINTAINERS entries for ids8247, jupiter, municse, sc3 and uc101Wolfgang Denk
boards. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12MPC512X: Cleanup bus clock names.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12MPC512X: Fixed typo in macro name.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12ads5121: Added support for FDT.Grzegorz Bernacki
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2008-01-12Coding Style cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12Fixed syntax error in function init_e300_core() of mpc83xx/start.S ifHeiko Schocher
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12MUNICes: Set the right CFG_DEFAULT_MBAR value.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12added the config File for the MUNICes board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12added basic support for the MUNICes board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Update CHANGELOG and MAINTAINERS files.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12Fix compilation problem in common/cmd_bmp.cAnatolij Gustschin
common/cmd_bmp.c fails to compile if CONFIG_VIDEO_BMP_GZIP isn't defined. This patch fix this. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-01-12Fix defaultconfig for the mgcoge board.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Added support for the mgcoge board from keymile.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Enable SMC microcode relocation patch for SMC1.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Added support for the mgsuvd board from keymile.Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-01-12Fix 64-bit vsprintf.James Yang
There were some size and unsigned problems. Also add support for "ll" size modifier in format string like glibc Signed-off-by: James Yang <James.Yang@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
2008-01-12Remove superfluous preprocessor conditionals from LM73 driverLarry Johnson
(1) Remove unused symbol "CFG_EEPROM_PAGE_WRITE_ENABLE". (2) Use conditional Makefile.o. Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-12Add support for the TK885D baseboard from TELE-DATAGuennadi Liakhovetski
The TK885D board uses a TQM885D module from TQ, this port adds an own configuration file and adds a last_stage_init() method to configure the two PHYs, depending on the phy_auto_nego environment variable. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-01-12Merge branch 'master' of git://www.denx.de/git/u-boot-videoWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-28 07:08:09 +0000