| Age | Commit message (Collapse) | Author |
|---|
|
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
syscon_regmap_lookup_by_phandle() can be used to get the regmap of a syscon
device from a reference in the DTS. It operates similarly to the linux
version of the namesake function.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This is now required because the PHY operations used by xhci-dwc3 are part
of the dwc3 core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
|
|
The driver will be probed when usb_gadget_initialize() is called.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
usb_gadget_initialize()/_release()/_handle_interrupt()
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.
usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This patch fixes the problem that u-boot will not start unless icache is
enabled early.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
|
|
This patch fixes the problem that "main memory domain AXI secure access
protection error" occurs. Exclude the area (0x43f00000 to 0x47DFFFFF)
set by DBSC from the map area.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
|
|
This patch fixes the problem that "main memory domain AXI secure
access protection error" occurs when booting Cortex-A53. Exclude
the area (0x43f00000 to 0x47DFFFFF) set by DBSC from the map area.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
|
|
This patch synchronizes the am33xx SoC specific files with those from
Linux 4.20.0. Hence all board maintainers of am33xx based boards are
on the cc list.
The main purpose of this patch is to prevent further diverging of the
dts files from U-Boot and those from Linux. It aims to set the stage
for the synchronization of board specific dts files. Example: I'm the
maintainer of the PDU001 board: once this patch is applied successfully
I will make changes to the board specific dts file in Linux only and
then post a patch with a copy of this exact dts file to U-Boot. This
will make U-Boot and Linux remain in sync.
The stumbling block of https://patchwork.ozlabs.org/patch/943627 was
removed by the patch https://patchwork.ozlabs.org/patch/962428 from
Lokesh Vutla (many thanks!). This omap-serial driver allows using the
Linux am33xx.dtsi file in U-Boot.
Other changes to dts and dtsi files made by this patch are mainly to
prevent _new_ warnings during the build process. Especially the warning
at pinmux@800 stating 'unnecessary #address-cells/#size-cells without
"ranges" or child "reg"' was not removed. This warning is a good example
showing the benefit of the synchronization: if it needs to be fixed it
will be fixed in Linux and ported back to U-Boot.
Buildman reports all 46 am33xx SoC based boards to build fine, with
warnings of course. Nevertheless this patch should be tested thoroughly
on as many boards as possible to prevent any collateral damage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
commit d6330064634a ("spl: Add a define for SPL_TPL_PROMPT")
changes the SPL/TPL banner from upper case into lower
case. As SPL and TPL are three-letter acronyms and they
are written in upper case, change it back to upper case.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There has been some natural evolution of the device tree, so
resync with 4.20
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Re-synce the device tree files from Linux 4.20
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Re-sync with 4.20 due some some natural evolution.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Migrate some small device tree fixes from Linux 4.20.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
There have been a few fixes to the device trees, so this
re-syncs the dts/dtsi files with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This patch adds code missing when CONFIG_DEBUG_UART_OMAP is enabled as
early debugging UART. The code is basically copied from the ns16550
driver.
Signed-off-by: Felix Brack <fb@ltec.ch>
|
|
Build tested in Travis, see:
https://travis-ci.org/abrodkin/u-boot/jobs/462808237
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
The DTS file for the AM3517 had the incorrect CD polarity. Resync with
the fixed DTS file from Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Hi,
setting active menuitem currently can be outside of menu which results in invisible selection
attached Patch fixes this
regards Frank
>From 1d9c4cb8b3e2dd9b0a7a6a2d4a21684d0a099dbf Mon Sep 17 00:00:00 2001
From: Frank Wunderlich <frank-w@public-files.de>
Date: Sun, 2 Dec 2018 11:23:53 +0100
Subject: [PATCH] ensure active menuitem is inside menu
if active menuitem is defined via environment var it can be outside the menu (>=menuitem-count)
this patch resets this definition back to 0
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
|
|
Due to gpio holes management, stm32_pinctrl_get_gpio_dev() must
be updated.
stm32_pinctrl_get_gpio_dev() returns from a given pin selectors
the corresponding bank gpio device and the gpio_offset inside this
gpio bank.
Update also all functions which makes usage of stm32_pinctrl_get_gpio_dev.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As all STM32 SoCs supports CONFIG_CLK flag,
it becomes useless in this driver, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
To allow access to this define by other driver, move
it into gpio.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Move gpio_dev list filling outside probe() to speed-up U-boot
boot sequence execution. This list is populated only when needed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001
board. It depends on Patrice Chotard's patch 'power: regulator: denied
disable on always-on regulator' which prevents power cycling the vmmc
supply. Without this patch the board will not boot as vmmc is
unfortunately used by other board components, not just eMMC and micro SD
card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card
detection input' is required to boot from external micro SD card. Without
this patch no SD card will be detected and hence booting will fail.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
|
|
Add a sandbox DMA driver implementation (provider) and corresponding DM
test.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This adds channels support for dma controllers that have multiple channels
which can transfer data to/from different devices (enet, usb...).
DMA channle API:
dma_get_by_index()
dma_get_by_name()
dma_request()
dma_free()
dma_enable()
dma_disable()
dma_prepare_rcv_buf()
dma_receive()
dma_send()
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[grygorii.strashko@ti.com: drop unused dma_get_by_index_platdata(),
add metadata to send/receive ops, add dma_prepare_rcv_buf(),
minor clean up]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move dma_ops to a separate header file, following other uclass
implementations. While doing so, this patch also improves dma_ops
documentation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
UART booting requires YMODEM support. Add this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add test for the SPL binary size and the bss section size.
This will throw an error at build time if the SPL sections
do not fit in the designated RAM area, thus avoiding oversizing the SPL.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
The pin number (first and last) in the bank definition is missing the
pin base offset shifting. This is causing a miscalculation when
retrieving the register and pin offsets in the GPIO driver causing the
'gpio' command to drive the wrong pins / GPIOs in the second GPIO chip
(the AO bank is driven correctly because the shifting is already 0).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Protect configuration registers with a hardware spinlock.
If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add hardware spinlock in the list of the clocks.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Currently k2 spi boot is broken as the image header
is getting copied to an invalid memory location
CONFIG_SYS_TEXT_BASE - sizeof (struct image_size)
which maps to 0xc000000 - 0x40 = 0xbffffc0 being a reserved
location.
We cannot change the CONFIG_SYS_TEXT_BASE address as the single
stage boots like UART boot will need the address to be 0xc000000
hence override the spl_get_load_buffer to have image_header
address as CONFIG_SYS_TEXT_BASE aka 0xc000000
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
In commit e5e06b65ad65 ("clk: Allow clock defaults to be set also
during re-reloc state") the earlier guard against setting clock
defaults in pre-reloc state was removed. While it is easy to filter
'assigned-clocks' properties for SPL using CONFIG_OF_SPL_REMOVE_PROPS,
no such mechanism exists for the pre-reloc stage of the full U-Boot.
With the default defconfig for the RK3399-Q7 (which filter the
'assigned-clocks' property for the DTS used by SPL anyway), this
caused a pause during startup of the full U-Boot stage that lasted for
almost 10s (due to the CPU not having been clocked up yet).
This reintroduces the guard from commit f4fcba5c5baa ("clk: Allow
clock defaults to be set also during re-reloc state") and extends it
to only apply outside of a TPL/SPL build: i.e. clk_set_defaults will
now run in pre-reloc state for SPL, but only after reloc for the full
U-Boot.
References: commit f4fcba5c5baa ("clk: implement clk_set_defaults()")
References: commit e5e06b65ad65 ("clk: Allow clock defaults to be set
also during re-reloc state")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The long name apparently can be accumulated using multiple
13-byte slots. Unfortunately we never checked how many we
can actually fit in the buffer we are reading to.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
|
|
The cluster size specifies how many sectors make up a cluster. A
cluster size of zero makes no sense, as it would mean that the
cluster is made up of no sectors. This will later lead into a
division by zero in sect_to_clust(), so better take care of that
early.
The MAX_CLUSTSIZE define can reduced using a define to make some
room in low-memory system. Unfortunately if the code reads a
filesystem with a bigger cluster size it will overflow the buffer.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
|
