summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-12-27Use out_be32() and friends to access memory-mapped registers in sequoia.cLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27Use definitions from "asm-ppc/mmu.h" in init.S for SequoiaLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27Cosmetic changes to ECC POST for AMCC Denali coreLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27ppc4xx: Fix compilation problem in 405 cache POST testStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Move virtual address of POST cache test to bigger addressStefan Roese
On Sequoia & LWMON5 the virtual address of the POST cache test is now moved to a bigger address. This enables usage of more memory on those boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Fix problem in 44x cache POST routineStefan Roese
As repoted by Larry Johnson, running "diag run cache" caused a crash in U-Boot. This problem was introduced by a patch that removed the TLB entry for the cache test after the test has completed. Since this TLB was only setup once, a 2nd attempt to run this cache test failed with a crash. Now this TLB entry is created every time the routine is called. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Update Makalu fdt supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Add fdt support to AMCC Katmai eval boardStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: fdt: Cleanup setup of cpu node setupStefan Roese
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is without using the absolute path to the cpu node. This makes it possible to use this U-Boot version with both versions of cpu-node naming "cpu@0" and the former "PowerPC,440EPx@0". Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Fix lwmon5 compilation problemStefan Roese
Now that the 440EPx ECC test is not board specific anymore remove this Makefile. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27Fix ppc4xx clear_bss() codeAnatolij Gustschin
ppc4xx clear_bss() fails if BSS segment size is not divisible by 4 without remainder. This patch provides fix for this problem. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2007-12-27PPC4xx: Minimal changes to add vxWorks supportNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-12-27ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board configMarkus Klotzbücher
When using dhcp/bootp the "netmask" environment variable is not set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is desireable, so the following patch adds this this option to the board config. Signed-off-by: Markus Klotzbuecher <mk@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27Fix/enhance ECC POST for 440EPx/GRxLarry Johnson
This patch allows the ECC POST to be used for different boards with the PPC440 Denali SDRAM controller. Modifications include skipping the test if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization to prevent timing errors. Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27PPC4xx: Move/rename ECC POST for 440EPx/GRxLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27ppc4xx: use correct io accessors for 4xx ethernet POSTMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-27ppc4xx: fix flush + invalidate_dcache_range argumentsMatthias Fuchs
flush + invalidate_dcache_range() expect the start and stop+1 address. So the stop address is the first address behind (!) the range. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-27ppc4xx: fdt: use fdt_fixup_ethernet()Stefan Roese
By using aliases in the dts file, the ethernet node fixup is much easier with the recently added functions. Please note that the dts file needs the aliases for this to work. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27ppc4xx: Bring 4xx fdt support up-to-dateStefan Roese
This patch update the 4xx fdt support. It enabled fdt booting on the AMCC Kilauea and Sequoia for now. More can follow later quite easily. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-11ppc4xx: Correct GPIO offset in gpio_config()Stefan Roese
Thanks to Gary Jennejohn for pointing this out. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-11rtc: Fix merging problemStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-11Merge commit 'u-boot/master' into for-1.3.1Stefan Roese
Conflicts: drivers/rtc/Makefile
2007-12-08ppc4xx: 405EX: Correctly enable USB pinsStefan Roese
This patch selects the USB data pins in the 405EX GPIO and MFC (multi function control) registers. This is done for the AMCC Kilauea and Makalu eval boards. Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-06Release v1.3.1Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-12-06ADS5121 Board: fix compile problem.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-12-06ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boardsStefan Roese
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by setting the FIXD bit in the SDR0_MFR register. Here a description of the symptoms: Problem Description ------------------------------ If a DMA is performed between memory and PCI with the DMA 1 Controller using prefetch, and as a result uses a special purpose buffer selected by the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29), the first part of the transfer sequence is performed twice. The PPC440SPe PCI Controller requests more data than was needed such that in the case of enforce memory protection, a host CPU exception can occur. No data is corrupted, because data transfer is stopped in the PCI Controller. Prefetch enable is specified by setting DMA Configuration Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0. Behavior that may be observed in a running system --------------------------------------------------------------------------- 1. DMA performance is decreased because of the double access on the PCI bus interface. 2. If an illegal access to some address on the PCI bus is detected at the system level, a machine check or similar system error may occur. Workarounds Available ---------------------------------- 1. Do not program prefetch. Note that a prefetch command cannot be programmed without selecting a special purpose buffer. 2. To avoid crossing a physical boundary of the PCI slave device, add 512 bytes of address to the PCI address range. This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com> from AMCC and slighly changed. Signed-off-by: Pravin M. Bathija <pbathija@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-04ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 supportStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-03Prepare for 1.3.1-rc1Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-11-30ppc4xx: Kilauea: Add PCIe reset assertion upon power-upStefan Roese
This manual PCIe reset triggering solves the problem seen with the Intel EPRO/1000 card, which was not detected (link not established) upon power-up reset. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-27ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexingStefan Roese
After an error in the AMCC 405EX users manual now correctly configure IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ usage. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26Merge commit '3deca9d'Wolfgang Denk
Conflicts: Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-11-26Cleanup coding style; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-11-26Merge commit '87ddedd'Wolfgang Denk
2007-11-26MAKEALL: add missing 512x boards in ppcJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-26Makefile : fix tags ctags etags with new drivers organizationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-26ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usageStefan Roese
As suggested by Senao, use a different EBC_PB0AP setup for 400MHz operation. Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-26ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interruptStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-25Makefile : fix tags ctags etags with new drivers organizationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/mtd : move mtd drivers to drivers/mtdJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/misc : move misc drivers to drivers/miscJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/block : move block drivers to drivers/blockJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/rtc : move rtc drivers to drivers/rtcJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/hwmon : move hardware monitor drviers to drivers/hwmonJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/input : move input drivers to drivers/inputJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/usb : move usb drivers to drivers/usbJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/serial : move serial drivers to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/net : move net drivers to drivers/netJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25drivers/video : move video drivers to drivers/videoJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-24drivers/pcmcia : move pcmcia drivers to drivers/pcmciaJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-24drivers/pci : move pci drivers to drivers/pciJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit (git 2.34.1) at 2024-12-29 04:08:13 +0000