summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-07-25net: sun8i_emac: Test the correct phyEmmanuel Vadot
H3/H5 can either use the internal phy or an external one. Before getting clock and resets for the internal phy, test that we are using it because otherwise it break emac when using an external phy. Tested-on: OrangePi PC2 (H5) Fixes: 2348453c41 (net: sun8i_emac: Add EPHY CLK and RESET support) Signed-off-by: Emmanuel Vadot <manu@freebsd.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: davinci_emac: convert to using the driver modelBartosz Golaszewski
Now that we removed all legacy boards selecting TI_EMAC we can completely convert the driver code to using the driver model. This patch also updates all remaining users of davinci_emac. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2019-07-25riscv: sifive: fu540: Sync-up config header with RISC-V QEMU supportAnup Patel
We typically use same set of distro images (yocto, debian, fedora, etc.) on both QEMU RISC-V virt machine and SiFive Unleashed board. With growing kernel and ramdisk images, we need to re-adjust default U-Boot environment variables. The config header for QEMU RISC-V virt machine has been already updated to handle bigger kernel and ramdisk images hence this patch updates SiFive FU540 config header accordingly. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Tested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
2019-07-25net: macb: Fix check for little-endian system in gmac_configure_dma()Anup Patel
Instead of depending on CONFIG_SYS_LITTLE_ENDIAN, we check at runtime whether underlying system is little-endian or big-endian. This way we are not dependent on any U-Boot specific OR compiler specific macro to check system endianness. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: Extend MACB driver for SiFive Unleashed boardAnup Patel
The SiFive MACB ethernet has a custom TX_CLK_SEL register to select different TX clock for 1000mbps vs 10/100mbps. This patch adds SiFive MACB compatible string and extends the MACB ethernet driver to change TX clock using TX_CLK_SEL register for SiFive MACB. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25Add support for the NXP LS1021A-TSN boardJianchao Wang
The LS1021A-TSN is a development board built by VVDN/Argonboards in partnership with NXP. It features the LS1021A SoC and the first-generation SJA1105T Ethernet switch for prototyping implementations of a subset of IEEE 802.1 TSN standards. Supported boot media: microSD card (via SPL), QSPI flash. Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which is 64 MB in size and has an erase sector size of 256KB (therefore, flashing the RCW would erase part of U-Boot). Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which is only 32 MB in size but has an erase sector size of 64KB (therefore the RCW image can be flashed without erasing U-Boot). To avoid the problems above, the U-Boot base address has been selected at 0x100000 (the start of the 5th 256KB erase sector), which works for all board revisions. Actually 0x40000 would have been enough, but 0x100000 is common for all Layerscape devices. eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is disabled. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com> Signed-off-by: Changming Huang <jerry.huang@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> [Vladimir] Code taken from https://github.com/openil/u-boot (which itself is mostly copied from ls1021a-iot) and adapted with the following changes: - Add a008850 errata workaround - Converted eTSEC, MMC to DM to avoid all build warnings - Plugged in distro boot feature, including support for extlinux.conf - Added defconfig for QSPI boot - Added the board/freescale/ls1021atsn/README.rst for initial setup - Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not get overwritten during copying of the u-boot.bin payload from MMC to DDR. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25configs: ls1021atwr: Fix distro_bootcmd for QSPI bootVladimir Oltean
Due to a typo, "run qspi_bootcmd" and "env exists secureboot" got concatenated instead of being separated by a semicolon. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25arm: ls1021atwr: Convert to use driver model TSEC driverBin Meng
Now that we have added driver model support to the TSEC driver, convert ls1021atwr board to use it. This depends on previous DM series for ls1021atwr: http://patchwork.ozlabs.org/patch/561855/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> [Vladimir] Made the following changes: - Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi - Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 - a mistake ported over from Linux. Each SGMII PCS lies on the private MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS). - Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs - Completely removed non-DM_ETH support from ls1021atwr - Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio" and from "fsl,tsec" to "fsl,etsec2" to match Linux
2019-07-25net: tsec: Change compatible strings to match LinuxVladimir Oltean
In the case of the tsec network driver, so far there has been no mainline user of DM_ETH where the DT bindings get used. In the case of the mdio bus, it looks like the "fsl,tsec-mdio" string was made up for the documentation, but there is no mainline code that parses the "compatible" property anyway. In both cases, there are no DT blobs that contain the old strings. So change the documentation to "fsl,etsec2" for the Ethernet ports and "fsl,etsec2-mdio" for the MDIO buses, which are strings that Linux also uses, at least for LS1021A. More compatible strings can be added once other (PowerPC) SoCs are migrated to DM_ETH. The current ls1021a.dtsi doesn't match what was documented for the MDIO buses anyway (the "compatible" is "gianfar" currently). This will be fixed in the next patch. Fixes: 69a00875e3db ("doc: dt-bindings: Describe Freescale TSEC ethernet controller") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: tsec: Common handling of MAC station address for DM_ETHVladimir Oltean
In tsec_init, the MAC address is retrieved from 2 different structures depending on whether DM_ETH is enabled or not. But since the field name is the same inside both structures, we can conditionally define the structure of the correct type and simplify the assignments. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: tsec: Make errors visibleVladimir Oltean
This replaces debug() calls with printf() so that it is immediately obvious from the console that something is wrong. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: tsec: Reverse Christmas tree notationVladimir Oltean
This is a cosmetic patch that reorders variable definitions in the inverse order of their line length, where possible. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: tsec: Fix offset of MDIO registers for DM_ETHVladimir Oltean
By convention, the eTSEC MDIO controller nodes are defined in DT at 0x2d24000 and 0x2d50000, but actually U-Boot does not touch the interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM, MDIO_EMAPM). That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM, MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at the 0x520 offset. So shift the DT-defined register map by the offset of MDIO_MIIMCFG when mapping the MDIO bus registers. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: tsec: Refactor the readout of the tbi-handle propertyVladimir Oltean
The point of this patch is to eliminate the use of the locally-defined "reg" variable (which interferes with next patch) and simplify the fallback to the default CONFIG_SYS_TBIPA_VALUE in case "tbi-handle" is missing. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net/macb: increase RX buffer size for GEMRamon Fried
Macb Ethernet controller requires a RX buffer of 128 bytes. It is highly sub-optimal for Gigabit-capable GEM that is able to use a bigger DMA buffer. Change this constant and associated macros with data stored in the private structure. RX DMA buffer size has to be multiple of 64 bytes as indicated in DMA Configuration Register specification. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: apply sane DMA configurationRamon Fried
DMA configuration was heavily dependent on the HW defaults, add function to properly set the required fields, including the new dma_burst_length. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add dma_burst_length configRamon Fried
GEM support higher DMA burst writes/reads than the default (4). add configuration structure with dma burst length so it could be applied later to DMA configuration. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add support for SGMII phy interfaceRamon Fried
This patch adds support for the sgmii phy interface, available only to DM users, dictated by current driver design. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: use bit access macro from header fileRamon Fried
macb.h provides macros for reading/setting bitfields, in macb registers and descriptors. use that instead of redefining them in the source file. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add support for faster clk ratesRamon Fried
add support for clock rates higher than 2.4Mhz Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: sync header definitions as taken from LinuxRamon Fried
Few registers and bits were added by Cadence and they were not updated in the headers. Take the latest definitions as defined in Linux header (5.1) that also includes some comments about existing registers. One register was improperly named (UR), fix that. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25doc: bindings: Add binding for register driven MDIO muxesAlex Marginean
This binding documents two properties that describe the registers used to perform MUX selection. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25drivers: net: driver for MDIO muxes controlled over I2CAlex Marginean
This driver is used for MDIO muxes driven over I2C. This is currently used on Freescale LS1028A QDS board, on which the physical MDIO MUX is controlled by an on-board FPGA which in turn is configured through I2C. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: designware: use 'phy_connect' instead of open codedSimon Goldschmidt
Using 'phy_connect' instead of 'phy_find_by_mask' and 'phy_connect_dev' both deduplicates code and adds support for 'fixed-link'. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: fsl_enetc: add support for SGMII 2500Alex Marginean
SGMII 2500 as supported on NXP SoCs requires AN to be disabled, handle this case in the enetc sgmii init code. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25configs: ls1028a: enable networking options in rdb, qds defconfigAlex Marginean
Enables ethernet, MDIO, PHY drivers for LS1028A RDB and QDS. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25arm: dts: ls1028a updates for network interfacesAlex Marginean
Defines LS1028A RDB SGMII port, QDS RGMII port. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: apply serdes configuration for ENETC Ethernet interfacesAlex Marginean
Ethernet interfaces using serial protocols go through the serdes block integrated in the SoC. This is accessed over dedicated internal MDIOs which are part of the Ethernet PCI functions. Set up serdes at _start, along with other protocol specific port/MAC configuration. MDIO code is shared with enetc_mdio, read/write functions are exported from fsl_enetc_mdio for this reason. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: add NXP ENETC MDIO driverAlex Marginean
Adds a driver for the MDIO interface currently integrated in LS1028A SoC. This MDIO interface is shared by multiple ethernet interfaces and is presented as a stand-alone PCI function on the SoC ECAM. Ethernet has a functional dependency on MDIO, for simplicity there is a single config option for both. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: add NXP ENETC ethernet driverAlex Marginean
Adds a driver for NXP ENETC ethernet controller currently integrated in LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces are presented as PCI EPs on the SoC ECAM. Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com> Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25include: configs: ls1028a: set SYS_RX_ETH_BUFFER to 8Alex Marginean
LS1028A ethernet interfaces work with at least 8 BDs, set number of buffers to match that. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-24Merge branch '2019-07-24-master-imports'Tom Rini
- Various Android related changes including A/B update and BCB updates - Assorted minor fixes
2019-07-24psci: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: arch/arm/mach-stm32mp/psci.c: warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes] warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes] Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-24distro_bootcmd: refactor virtio to support PCI block devicesDavid Abdurachmanov
Starting libvirt v5.3.0 with QEMU 4.0.0 use of PCI is automatic and thus storage is connected via PCI, which is not visible to U-Boot out-of-the-box. Refactor to do "pci enum" followed by "virtio scan" to see PCI connected storage, and allow bootloader to load kernel and initramfs images. Tested with Fedora/RISCV using releases: libvirt 5.4.0 & 5.5.0, QEMU 4.0.0 and U-Boot 2019.07 RC4. Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
2019-07-24remoteproc: Fix potential build issues with SPL remoteprocSuman Anna
The rproc uclass driver can either be built with SPL_REMOTEPROC or REMOTEPROC, but the function prototypes in remoteproc.h are defined only when CONFIG_REMOTEPROC is defined. This can cause build issues in SPL if CONFIG_REMOTEPROC is not selected. Fix this by replacing the existing precompiler macro usage with CONFIG_IS_ENABLED. Fixes: ddf56bc7e3ef ("drivers: Introduce a simplified remoteproc framework") Signed-off-by: Suman Anna <s-anna@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-24doc: fitImage: Cosmetics break linesMickaël Tansorier
Add missing newline before title and subtitle. Signed-off-by: Mickaël Tansorier <mickael.tansorier@smile.fr>
2019-07-24doc: fitImage: Fix conf number incrementationMickaël Tansorier
Increment conf id to avoid to have two same conf name into one configuration description. Signed-off-by: Mickaël Tansorier <mickael.tansorier@smile.fr>
2019-07-24doc: Add the U-Boot logo to the html docBin Meng
Now we have a logo for U-Boot, we can include it in the Sphinx html doc. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-24doc: Add .gitignore for the Sphinx build output directoryBin Meng
With Sphinx documentation moving from Documentation directory to doc directory, we missed updating .gitignore for the Sphinx build output directory. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-24spl: sata: support U-Boot load from raw sata diskBaruch Siach
Support load of the U-Boot image from raw SATA disk sector. This is equivalent to load from MMC raw sector. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2019-07-24scripts/kernel-doc: fix parsing of function pointersHeinrich Schuchardt
kernel-doc fails to parse function definitions like the one below efi_status_t efi_create_event(uint32_t type, efi_uintn_t notify_tpl, void (EFIAPI *notify_function) ( struct efi_event *event, void *context), void *notify_context, efi_guid_t *group, struct efi_event **event) { due to the "EFIAPI" attribute preceding the function name. cf. https://lkml.org/lkml/2018/9/3/1185 Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-07-24scripts/kernel-doc: update script from Linux 5.2Heinrich Schuchardt
Update the script from Linux 5.2 to avoid some warnings. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-07-24doc: Cope with Sphinx logging deprecationsJonathan Corbet
Recent versions of sphinx will emit messages like: doc/sphinx/kerneldoc.py:103: RemovedInSphinx20Warning: app.warning() is now deprecated. Use sphinx.util.logging instead. Switch to sphinx.util.logging to make this unsightly message go away. Alas, that interface was only added in version 1.6, so we have to add a version check to keep things working with older sphinxes. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Rebased for U-Boot Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-07-24env: am57xx: Implement A/B boot processRuslan Trofymenko
Add support for A/B boot process on AM57xx based boards: 1. Define 'slot_suffix' variable (using 'ab_select' command) 2. Extend 'emmc_android_boot' boot command (add commands for A/B boot process) 'ab_select' command is used to decide which slot should be used for booting up. A/B metadata resides in 'misc' partition. To activate the A/B boot process, the following config options must be set: CONFIG_ANDROID_AB=y CONFIG_CMD_AB_SELECT=y For successful A/B boot, the corresponding A/B infrastructure must be involved on Android side [1] (including mounting system as root), and disk must be partitioned accordingly. When A/B boot is enabled, there are some known limitations currently exist (not related to A/B patches, need to be implemented later): 1. The 'Verified Boot' sequence is not supported 2. dev path to system partition (system_a or system_b) is passed via 'bootargs' as 'root=' argument like 'root=/dev/mmcblk1p12', but further we'll need to rework it with respect to dm-verity requirements [2] In case when A/B partitions are not present in system (and A/B boot is enabled), boot up process will be terminated and next message will be shown: "boot_a(b) partition not found" [1] https://source.android.com/devices/tech/ota/ab [2] https://source.android.com/devices/tech/ota/ab/ab_implement#kernel Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Alistair Strachan <astrachan@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24doc: android: Add simple guide for A/B updatesRuslan Trofymenko
Add a short documentation for A/B enablement and 'ab_select' command usage. Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Alistair Strachan <astrachan@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24test/py: Add base test case for A/B updatesRuslan Trofymenko
Add sandbox test for 'ab_select' command. Test: ./test/py/test.py --bd sandbox --build -k test_ab Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Alistair Strachan <astrachan@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24cmd: Add 'ab_select' commandRuslan Trofymenko
For A/B system update support the Android boot process requires to send 'androidboot.slot_suffix' parameter as a command line argument. This patch implementes 'ab_select' command which allows us to obtain current slot by processing the A/B metadata. The patch was extracted from commit [1] with one modification: the separator for specifying the name of metadata partition was changed from ';' to '#', because ';' is used for commands separation. [1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2 Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Alistair Strachan <astrachan@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24common: Implement A/B metadataRuslan Trofymenko
This patch determines the A/B-specific bootloader message structure that is the basis for implementation of recovery and A/B update functions. A/B metadata is stored in this structure and used to decide which slot should we use to boot the device. Also some basic functions for A/B metadata manipulation are implemented (like slot selection). The patch was extracted from commits [1], [2] with some coding style fixes. [1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729878/2 [2] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2 Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24disk: part: Extend API to get partition infoRuslan Trofymenko
This patch adds part_get_info_by_dev_and_name_or_num() function which allows us to get partition info from its number or name. Partition of interest is specified by string like "device_num:partition_number" or "device_num#partition_name". The patch was extracted from [1]. [1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2 Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com> Reviewed-by: Alistair Strachan <astrachan@google.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-24cmd: bcb: Apply non-functional refinementsEugeniu Rosca
These have been reported by Simon in [1] and fixed in [2]. However, since [1] has already been pushed to u-boot/master, the improvements incorporated in [2] are now extracted and resubmitted. The changes are in the area of coding style and best practices: * s/field/fieldp/, s/size/sizep/, to convey that the variables return an output to the caller * s/err_1/err_read_fail/, s/err_2/err_too_small/, to be more descriptive * Made sure 'static int do_bcb_load' appears on the same line * Placed a `/*` on top of multi-line comment [1] https://patchwork.ozlabs.org/patch/1104244/#2200259 [2] https://patchwork.ozlabs.org/cover/1128661/ ("[v4,0/4] Add 'bcb' command to read/modify/write Android BCB") Fixes: db7b7a05b267 ("cmd: Add 'bcb' command to read/modify/write BCB fields") Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
generated by cgit (git 2.34.1) at 2025-01-13 17:54:17 +0000