summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-11-26powerpc/mpc85xx/p1_p2_rdb_pc: clean up memory mapScott Wood
- Sort by address, and fix column alignment - Don't label things as localbus that aren't. Instead, put chipselect info at the end of the description for localbus windows. Note that NAND/NOR have their chipselects swapped when booting from NAND, and CS2 can be either PMC or VSC7385 depending on hwconfig. - Shrink NAND to the 32K that's actually mapped in the localbus - Assign an address and size to L2 SRAM. Remove the similarly named but unintelligible "L2 SDRAM(REV.)". - Remove the untrue comment about L1 stack being mapped with TLB0. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx/p1_p2_rdb_pc: convert from nand_spl to new splScott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/nand: config symbol documentationScott Wood
Document parameters used for specifying the NAND image to be loaded. Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only nand_spl_simple.c, not the entire nand directory. The word "simple" is there for a reason. :-) Signed-off-by: Scott Wood <scottwood@freescale.com> --- v2: updated for makefile changes earlier in patchset
2012-11-26spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.Scott Wood
Some small SPLs do not use nand_base.c, and a subset of those also require a special driver. Some SPLs need software ECC but others can't fit it. All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these symbols added to preserve existing behavior. Signed-off-by: Scott Wood <scottwood@freescale.com> -- v2: use positive logic for including bits of NAND, rather than a MINIMAL symbol that excludes things.
2012-11-26powerpc/mpc85xx/p1_p2_rdb_pc: new SPL supportScott Wood
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/85xx: new SPL supportScott Wood
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once the last mpc85xx nand_spl target is gone. CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't seem right to overload it for meaning SPL as well as nand_spl does. Even if it's somewhat appropriate for the main u-boot, the SPL itself isn't (necessarily) ramboot, and we don't have separate configs for SPL and main u-boot. It was also inconsistent, as other platforms such as mpc83xx didn't use CONFIG_RAMBOOT in this way. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/powerpc: introduce CONFIG_SPL_INIT_MINIMALScott Wood
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific. Signed-off-by: Scott Wood <scottwood@freescale.com> --- v2: factor out START, and change cpu_init_nand.c to spl_minimal.c Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx: consistently use COBJS-yScott Wood
A subsequent patch will conditionalize some of the files that are currently unconditional. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl/mpc85xx: rename cpu_init_nand.c to spl_minimal.cScott Wood
There is nothing really NAND-specific about this file. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26spl: include resetvec and lib8xxxScott Wood
The toplevel makefile hardcodes this stuff, so spl/Makefile needs to as well. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-11-26spl/mpc85xx: move udelay to cpu codeScott Wood
It applies to non-Freescale 85xx boards as well as Freescale boards, so it doesn't belong in board/freescale. Plus, it needs to come out of nand_spl if it's to be used by the new SPL. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc8xxx: move LAW code into arch/powerpc/cpu/mpc8xxxScott Wood
It's arch code and not a driver, so move it where it belongs. When it originally went into drivers/misc there was no 8xxx CPU directory. This will make new-SPL support a little easier since we can keep the CPU stuff together and not need to pull stuff in from drivers/misc. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx: fix TLB alignmentScott Wood
In the RAMBOOT/SPL case we were creating a TLB entry starting at CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly aligned for the TLB entry size. This turned out to not be the case with NAND SPL because the main U-Boot starts at an offset into the image in order to skip the SPL itself. Fix the TLB entry to always start at a proper alignment. We still assume that CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary thus requiring multiple TLB entries. Signed-off-by: Scott Wood <scottwood@frescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc: change .fixup test to a GCC version testScott Wood
This was introduced by commit 244615197469dd6fe75ae082f38424b97c79aeaf, but it fails in a minimal SPL build where the only thing in arch/powerpc/lib is cache.c, which apparently doesn't generate any fixup records. The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer. Patterned after checkthumb as suggested by Tom Rini. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Tom Rini <trini@ti.com> -- v2: test gcc version instead of testing nothing
2012-11-26spl: introduce CONFIG_SPL_TARGETScott Wood
Currently the SPL target is specified in a CPU-specific makefile fragment. While some targets may need something more complicated than a simple target name, targets which don't need this shouldn't have to provide a makefile fragment just for this. Signed-off-by: Scott Wood <scottwood@freescale.com> --- v2: Removed default target as it's been pointed out to me how existing platforms cause the SPL to be built.
2012-11-26spl: rename u-boot-pad.bin to u-boot-with-spl.binScott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-11-26Add u-boot-pad.bin target to the MakefileJosé Miguel Gonçalves
Samsung's S3C24XX SoCs need this in order to generate a binary image with a padded SPL concatenated with U-Boot. Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt> [scottwood@freescale.com: fixed prereq of u-boot.ubl] Signed-off-by: Scott Wood <scottwood@freescale.com> -- v2: Removed spl/ prefix from u-boot.ubl prerequisite.
2012-11-26powerpc/mpc85xx: add comma before "already enabled"Scott Wood
Now outputs like this: L2: 512 KB already enabled, moving to 0xf8f80000 rather than this: L2: 512 KB already enabledmoving to 0xf8f80000 Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@gmail.com>
2012-11-26powerpc/mpc85xx: move debug tlb entry after TLB is in known stateScott Wood
Previously, in many if not all configs we were creating overlapping TLB entries which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL into L2 SRAM. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Andy Fleming <afleming@freescale.com> -- Prabhakar, please test that debug still works.
2012-11-26serial/ns16550: wait for TEMT before initializingScott Wood
TEMT is set when the transmitter is totally empty and all output has finished. This prevents output problems (including a loss of synchronization observed on p2020 that persisted for quite a while) if SPL has output still on its way out. Signed-off-by: Scott Wood <scottwood@freescale.com> -- v2: fixed typo in subject, and explained what the bit does in the changelog
2012-11-26serial/ns16550: don't build serial_ns16550 with MIN_FUNCTIONSScott Wood
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic ns16550 output code without pulling in things not needed by the SPL. This previously only worked with non-MULTI configs. Recently MULTI was made mandatory, and MIN_FUNCTIONS fails like this: drivers/serial/libserial.o: In function `calc_divisor.clone.0': serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq' drivers/serial/libserial.o: In function `_serial_getc': (.text._serial_getc+0x30): undefined reference to `NS16550_getc' drivers/serial/libserial.o: In function `_serial_tstc': (.text._serial_tstc+0x30): undefined reference to `NS16550_tstc' drivers/serial/libserial.o: In function `_serial_setbrg': (.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit' make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1 make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2 With MIN_FUNCTIONS we don't need anything from this file, so don't build it. The conditional needs to be in the file itself rather than the makefile, because the config symbols are only imported to the makefiles once, not separately for the SPL phase of the build. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-11-19Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2012-11-19Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini
2012-11-14cmd_mmc.c: Fix typo, "dislay" -> "display"Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-11-14mx53loco: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan
The inclusion of LCD patch into mx53loco breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14mx51evk: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan
The inclusion of LCD patch into mx51evk breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14fs/fs.c: do_fsload: measure throughputAndreas Bießmann
This patch adds time measurement and throughput calculation for all supported load commands. The output of ext2load changes from ---8<--- 1830666 bytes read --->8--- to ---8<--- 1830666 bytes read in 237 ms (7.4 MiB/s) --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> [agust: rebased and revised commit log] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-14fs: zfs: fix illegal use of fpAlejandro Mery
the upcoming sunxi (allwinner a10/a13) platform enables zfs by default, and using linaro's hf -msoft-float makes the build fail because this u64 division. Signed-off-by: Alejandro Mery <amery@geeks.cl> Acked-by: Stefan Roese <sr@denx.de>
2012-11-14Video: fix compiler warnings in bus_vcxkJens Scharsig (BuS Elektronik)
if a board uses the vcxk driver option CONFIG_SYS_VCXK_DOUBLEBUFFERD, compilier shows warnings. This patch will fix it. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-11-14M68K: eb_cpu5282: general update and enhanced board supportJens Scharsig (BuS Elektronik)
- update clock settings for higher perfomance - change standard baud rate to 115200 - fix flash base address - remove unused defines - add I2C support - switch form board dependent flash to cfi - remove board dependent flash code - use sdram bank 0 instead of bank 1 on boot - enable on board frame buffer instead external - remove fake mac address form config - add watchdog support - add status led support Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> [agust: fixed small style issues and build warning] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-14arm:universal_c210:pmic: Adjust C210 Universal target platform board to new ↵Łukasz Majewski
PMIC framework Move pmic_init() function call from board_init() to power_init_board() to work with new PMIC/POWER framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:goni:pmic: Adjust GONI target platform board to new PMIC frameworkŁukasz Majewski
Move pmic_init() function call from board_init() to power_init_board() to work with new PMIC/POWER framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14power:pmic: Rename CONFIG_DIALOG_PMIC defines to CONFIG_DIALOG_POWERŁukasz Majewski
Rename CONFIG_DIALOG_PMIC to CONFIG_DIALOG_POWER Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14power:pmic: Rename CONFIG_PMIC* defines to CONFIG_POWERŁukasz Majewski
Rename all CONFIG_PMIC* defines to CONFIG_POWER* Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14power:pmic: Rename ./drivers/power/pmic_* to ./drivers/power/power_* filesŁukasz Majewski
Rename pmic/power related files at ./drivers/power directory Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14pmic: Extend PMIC framework to support battery related commandsŁukasz Majewski
Two extra commands: "pmic name bat state" and "pmic name bat charge" has been added to pmic framework. Those provides state display and charge capabilities to named batteries. The pmic_core.c file has been refactored to more consistent name scheme. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14arm:trats:pmic: Support for charging battery at Samsung's TRATS boardŁukasz Majewski
The battery connected to Samsung's Trats development board is now charged when voltage drops below threshold. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Power consumption reduction state for Samsung's TRATS boardŁukasz Majewski
When charging battery is necessary, the development board needs to be turned into low power mode for better efficiency. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14pmic:max8997: Support for MAX8997 internal charger controlŁukasz Majewski
Support for MAX8997 built-in charger. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14arm:trats:pmic: Enable battery support at Samsung's TRATS boardŁukasz Majewski
Support for TRATS battery has been added. It is treated as a "normal" power related device and thereof controlled by pmic/power subsystem. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Enable fuel-gauge (MAX17042) at Samsung's TRATS boardŁukasz Majewski
FG IC built into the MAX8997 device (compliant to MAX17042) is enabled at TRATS. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Enable MUIC (MAX8997) at Samsung's TRATS boardŁukasz Majewski
MUIC IC built into the MAX8997 device is enabled at TRATS. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Default PMIC(MAX8997) initialization for Samsung's TRATS boardŁukasz Majewski
Default PMIC (MAX8997) initialization for Samsung's TRATS development board. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14pmic:max8997: Function for calculating LDO internal register valueŁukasz Majewski
Function for calculating LDO internal register value from passed micro Volt. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14pmic:fuel-gauge: Support for MAX17042 fuel-gaugeŁukasz Majewski
Support for MAX17042 fuel-gauge (FG), which is built into the MAX8997 power management device. Special file - fg_battery_cell_params.h with cells characteristics added. The FG device will work with redesigned PMIC framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14pmic:muic: Support for MUIC built into MAX8997 deviceŁukasz Majewski
Support for MUIC (Micro USB Integrated Circuit) built into the MAX8997 power management device. The MUIC device will work with redesigned PMIC framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14pmic:battery: Support for Trats Battery at PMIC frameworkŁukasz Majewski
Trats battery is now treated in the same way as other power related devices. This approach allows for more unified handling of all devices responsible for power management. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14pmic: Extend struct pmic to support battery and charger related operationsŁukasz Majewski
Now it is possible to provide specific function per PMIC/power device instance. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-11-14pmic: Move pmic related code to ./drivers/power directoryŁukasz Majewski
The PMIC framework has been moved to its more natural place ./drivers/power from ./drivers/misc directory. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-11-14pmic:chrg: Common information about charger and battery (power_chrg.h)Łukasz Majewski
New power_chrg.h file has been added to "bind" together common information about charging battery available in the system. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit (git 2.34.1) at 2024-12-29 02:28:08 +0000