summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-25warp7: Fix dfu_alt_info setting after DM conversionPierre-Jean Texier
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase the "size" of the dfu_alt_info setting. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-04-25dts: imx6ull: add USB aliases to support DMFilip Brozovic
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
2019-04-25imx8qxp_mek: drop warning due to unused variableStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-04-25pico-imx7d: Increase u-boot size for dfu requestJoris Offouga
After DM conversion, the size of U-Boot binary to increase. Previous size is 480K after DM Conversion the new size is 557K So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC. Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-04-25pico-imx7d: Convert DM MMCJoris Offouga
This patch enable convert DM MMC for imx7d-pico board and variant. Before the DM conversion only usdhc3 was enabled and therefore it appeared as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2, which left unattended would drive changes to existing pico-pi bootscripts and environment variables that rely on mmc 0. Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will work unmodified. When converting to DM_MMC it is necessary that SPL initializes eMMC by itself, so move the original eMMC initialization from U-Boot proper to SPL. Signed-off-by: Joris Offouga <offougajoris@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-25board: toradex: tdx-cfg-block: add new skusMarcel Ziswiler
Add all the latest new SKUs: - Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT - Apalis iMX8 QuadMax 4GB IT - Apalis iMX8 QuadPlus 2GB Wi-Fi / BT - Apalis iMX8 QuadPlus 2GB", - Colibri iMX8 QuadXPlus 2GB IT - Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth - Colibri iMX8 DualX 1GB Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25pico-imx7d: defconfig Enable DM gpio pinctrl and pinctrl_imx7Joris Offouga
This patch is necessary for convert this board to dm driver model DM GPIO requires gpio_request() to be called explicitly before doing any gpio operation Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-04-25board: toradex: tdx-cfg-block: clean-up sku handlingMarcel Ziswiler
Clean-up handling of several SKUs. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25pico-imx7d: defconfig: Add DT file hooksJoris Offouga
This patch adds DT file hooks for Pico i.MX7D SOM and variant boards Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-04-25arm: dts: imx8dx: add lpuart1, lpuart2, lpuart3Marcel Ziswiler
Add support for lpuart1, lpuart2 and lpuart3. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25misc: imx8: remove duplicates from scfw apiMarcel Ziswiler
Remove duplicate function declarations from the SCFW API header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25Arm: imx7d-pico: Import all Linux device tree for Pico i.MX7D SOMJoris Offouga
This patch imports the Linux kernel base board imx7d-pico.dtsi, pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts from Linux v5.1-rc1. Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-04-25ARM: dts: colibri-imx6ull: fix uart-has-rtscts propertyMarcel Ziswiler
Remove vendor pre-fix fsl, from uart-has-rtscts property. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate fec to using driver modelMarcel Ziswiler
Migrate Ethernet FEC to using driver model. Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate usb to using driver modelMarcel Ziswiler
Migrate USB to using driver model. Add USBH_PEN GPIO regulator. While at it also add alias e.g. as required for UMS. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate mmc to using driver modelMarcel Ziswiler
Migrate MMC to using driver model. Migrate USDHC to using pinctrl. While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler
Migrate pinctrl and regulators to device tree resp. driver model: Ethernet, NAND and UART. Drop BOARD_EARLY_INIT_F as it is anyway no longer used. Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: configuration clean-upMarcel Ziswiler
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL. Enbale CRC32 verify, USB SDP and EFI loader support. Drop CMD_GPT and disabling RANDOM_UUID. Do savedefconfig which drops USB_FUNCTION_SDP. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25board: imx6ull: Add disable PMIC_STBY_REQPhilippe Schenker
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the SOC to request for a lower voltage during sleep. This is necessary because the voltage is changing too slow for the SOC to wake up properly. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: fix ethernet phy power onMarcel Ziswiler
Just give the new Ethernet PHY power save mode circuitry time to settle. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25apalis/colibri_imx6/imx6ull: make sure loadaddr does not collideStefan Agner
Currently $loadaddr and $fdt_addr_r point to the same address. This might be not ideal for some distro boot scripts which make use of $loadaddr after loading the device tree. Make sure the two variables point to two different addresses. Moving $loadaddr is not entirly trivial since it is defined in mx6_common.h. Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough for scripts. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri-imx6ull: set module variant depending on config blockStefan Agner
Using CPU temperature grading as a discriminator if the Wi-Fi / Bluetooth chip is populated is no longer possible due to upcoming SKUs. Set variant to -wifi only if a valid config block is present and the product id mentions a SKU with Wi-Fi / Bluetooth. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25tdx-cfg-block: simplify i.MX 6 module detectionStefan Agner
Use CONFIG_TARGET_... at compile time to differentiate between Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code duplication by moving question about Wi-Fi / Bluetooth before IT/non-IT decision. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25tdx-cfg-block: add support for new colibri iMX6ull skusGerard Salvatella
Add support for new Colibri iMX6ULL SKUs. While at it also checkpatch fix the whole files. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri_vf: fix tab vs. spacesMarcel Ziswiler
Fix indentation using tab vs. spaces. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri_vf: fix ethernet by adding explicit phy nodeMarcel Ziswiler
The implicit fallback mechanism for searching the whole MDIO bus for at least one PHY has been gone with the following commit b882005a18de ("drivers/net/fec: phy_init: remove redundant logic"). This lead to the Ethernet driver erroring out as follows: Net: Could not get PHY for FEC0: addr -19 eth-1: fec@400d1000 Colibri VFxx # dhcp Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 Could not get PHY for FEC0: addr -19 No ethernet found. Could not get PHY for FEC0: addr -19 Colibri VFxx # This commit adds an explicit PHY node which makes it work again. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25imx: support i.MX8QM MEK boardPeng Fan
Add i.MX8QM MEK board support. Included a basic dts, enabled SPL FIT Boot log as below: U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) Normal Boot Trying to boot from MMC2_2 U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) CPU: NXP i.MX8QM RevB A53 at 142933 MHz Model: Freescale i.MX8QM MEK Board: iMX8QM MEK Build: SCFW 9330215b Boot: SD1 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: Error: ethernet@5b040000 address not set. eth-1: ethernet@5b040000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25misc: imx8: scu: add i.MX8QM supportPeng Fan
According to IMX8QXP/8QM config option, choose the clk/iomuxc compatible. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx8: imx8-pins: add i.MX8QMPeng Fan
Add i.MX8QM entry Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25clk: imx8: add i.MX8QM clk driverPeng Fan
Add i.MX8QM clk driver, SDHC/FEC/UART/I2C supported. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25clk: imx8: split code into common and soc specific partPeng Fan
To make it easy to add new clk driver for i.MX8, split the code into common part and SoC specific part. Make the get/set/enable non static and introduce a num_clks for soc_clk_dump, because the arrays are moved to clk-imx8qxp.c. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx8: add cpu supportPeng Fan
Add cpu type and Kconfig entry Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25arm: dts: introduce dtsi for i.MX8QMPeng Fan
Introduce basic dtsi for i.MX8QM, only support SDHC/FEC/LPUART. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25dt-bindings: clock: dt-bindings: pinctrl: add i.MX8QM clocks definitionPeng Fan
Add i.MX8QM clocks definition Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25dt-bindings: pinctrl: add i.MX8QM pads definitionPeng Fan
Add i.MX8QM pads definition Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25pinctrl: imx8: add i.MX8QM compatiblePeng Fan
Add i.MX8QM compatible Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25boot.src: Provide dsa_core.blacklist bootarg when booting via NFSLukasz Majewski
This setup is a bit special as Linux kernel (4.19) is not supporting in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA) operation. For that reason it was necessary to provide a bootarg to allow userspace enable it afterwards if needed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25Convert CONFIG_USB_EHCI_MX5 to KconfigLukasz Majewski
This converts the following to Kconfig: CONFIG_USB_EHCI_MX5 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: config: Remove not needed CONFIG_MXC_USB_PORT defineLukasz Majewski
After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed anymore and should be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: defconfig: kp_imx53: Enable DM_USB support on HSC|DDC boardsLukasz Majewski
This commit enables the DM_USB on HSC|DDC i.MX53 based boards. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25USB: DM: Convert i.MX5 ehci code to driver modelLukasz Majewski
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB). It is a straightforward conversion (to reuse as much code as possible), based on ehci-mx6.c code. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove EHCI specific code from HSC|DDC board fileLukasz Majewski
As EHCI on i.MX5 has been converted to driver model, the board specific code, necessary for VBUS USB power supply setup is not needed anymore. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Enable USB host support (including regulators) on HSC|DDC boardsLukasz Majewski
This commit enables the support for K&P's HSC|DDC imx53 based boards. It was also necessary to provide device tree description for regulators to avoid board specific code definition. The GPIO pin description responsible for VBUS control has been moved from "hog" group to usbh1 dedicated one. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Provide USB host DTS description for i.MX53 devicesLukasz Majewski
This code has been ported from Linux kernel - tag v5.1-rc2. The difference from the kernel is the removal of: fsl,usbmisc = <&usbmisc 1>; fsl,usbphy = <&usbphy1>; properties, which are not needed for correct u-boot operation (as PHY setup is done in ehci-mx5.c file itself). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: kp_imx53: config: Do not use ${boardtype} to setup update wic fileLukasz Majewski
After unification of the rootfs for both HSC and DDC devices, only one, common wic file is necessary - without the distinction of specific board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove non DM/DTS esdhc3 code from HSC|DDC board related filesLukasz Majewski
After switching to DM/DTS support of esdhc3 - the code in this patch can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: defconfig: Move CONFIG_FSL_ESDHC to KconfigLukasz Majewski
The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in include/configs/kp_imx53.h Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Enable CONFIG_DM_MMC and CONFIG_DM_BLK on HSC and DDC boardsLukasz Majewski
This commit enables DM_MMC and DM_BLK on imx53 based HSC and DDC boards. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25DTS: Add esdhc3 device tree description tuning for HSC|DDC boardsLukasz Majewski
In this commit the esdhc3 controller is enabled as well as it is remaped to mmc0 to not break legacy code. The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file definition. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove HSC|DDC ETH PHY reset code after switching to DM/DTSLukasz Majewski
After commit efd0b791069a ("eth: dm: fec: Add gpio phy reset binding") the in-board file definition of ETH PHY reset can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-30 20:52:21 +0000