summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2009-03-24Blackfin: bf533-stamp: rewrite startup LED notificationsMike Frysinger
Again, don't clobber pins that we aren't actually using, and use the common LED framework rather than our own hob-job-but-not-really-working. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24Blackfin: unify common ADI board settingsMike Frysinger
Rather than duplicate the same ADI settings in every ADI board, create a common ADI config header and have all ADI boards start using that. This will also make merging the ~10 boards I have to forward port a lot easier. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Reduce OneNAND IPL common codeKyungmin Park
OneNAND IPL has common codes for RAM init, load data, and jump to 2nd bootloader, but it's common code used about 300~400 bytes. So board specific codes, such as lowlevel_init, can't has enough code. It make a difficult to implement OneNAND IPL. his patch make this common code as small as possible. and give lowlevel_init can have more codes. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Add multi-chip NAND support for the TQM8548 modulesWolfgang Grandegger
This patches configures the NAND UPM-FSL driver with multi-chip support for the Micron MT29F8G08FAB NAND flash memory on the TQM8548 modules. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Add wait flags to support board/chip specific delaysWolfgang Grandegger
The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The corresponding Linux FSL UPM driver uses similar delay points at the same locations. To manage these extra delays in a more general way, I introduced the "wait_flags" field allowing the board-specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Add support for TQM-specific chip select logic to FSL-UPMWolfgang Grandegger
For the NAND chips on the TQM8548 modules, a special chip-select logic is used. It uses dedicated address lines to be set via UPM machine address register (mar). This patch adds such support to the FSL-UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Add multi chip support to the FSL-UPM driverWolfgang Grandegger
This patch adds support for multi-chip NAND devices to the FSL-UPM driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now called with the argument "chip_nr" to allow testing the proper chip select line. The NAND support of the MPC8360ERDK is updated as well. No other boards are currently using the FSL UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Enable multi chip support in the NAND layerWolfgang Grandegger
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer. Multi-chips devices are displayed as shown: Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23Blackfin: put memory into self-refresh before/after programming clocksMike Frysinger
When initializing the core clocks, stick external memory into self-refresh. This gains us a few cool things: - support suspend-to-RAM with Linux - reprogram clocks automatically when doing "go" on u-boot.bin in RAM - make sure settings are stable before flashing new version - finally fully unify initialize startup code path between LDR/non-LDR Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: do not program voltage regulator on parts that do not have oneMike Frysinger
Some newer Blackfins (like the BF51x) do not have an on-chip voltage regulator, so do not attempt to program the memory as if it does. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: setup a sane default EBIU_SDBCTL for SDRAM controllersMike Frysinger
If the board config does not specify an explicit EBIU_SDBCTL value, set it up with sane values based on other configuration options. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: handle reboot anomaly 432Mike Frysinger
Workaround anomaly 432: The bfrom_SysControl() firmware function does not clear the SIC_IWR1 register before executing the PLL programming sequence. Therefore, any interrupt enabled in the SIC_IWR1 register prior to the call to bfrom_SysControl() can prematurely terminate the idle sequence required for the PLL to relock properly. SIC_IWR0 is properly handled. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: kill off LDR jump blockMike Frysinger
The Boot ROM uses EVT1 as the entry point so set that rather than having to use a tiny jump block in the default EVT1 location. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: simplify symbol_lookup() a bitMike Frysinger
No need to skip a byte as the symbol table handles this. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: fix SIC_RVECT definition: it is 16bits, not 32bitsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: drop SPORT_TX read helper macrosMike Frysinger
The SPORT_TX registers cannot be read (the hardware will trigger an error), so drop the read helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: unify duplicate CPU port definitionsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: drop now-unused CONFIG_SYS_BFIN_CMD_XXXMike Frysinger
With the new CONFIG_XXX system and CONFIG_CMD_XXX handling, these defines are no longer used/needed. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: print out Flash: before checking itMike Frysinger
If there is some problem in the flash init/checking code, it's nicer to see the message "Flash:" before crashing. This way the source of the problem is a bit more straightforward. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: safely flush data caches when in writeback modeMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: update lockbox api according to latest documentationMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: mark bfin_reset staticMike Frysinger
The function is only used locally, so mark it static. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: spi: there is no PORTJ_FER MMR on BF537Sonic Zhang
Since the PORTJ on the BF537 is peripheral-only (no GPIO functionality), then there is no PORTJ_FER register for us to worry about. Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: fix jtag console tstcMike Frysinger
The jtag tstc operation was checking the hardware to see if data is available from it (which is fine for the jtag getc operation), but the higher layers need to know whether any data is available. Since we have to read up to 4 bytes at a time from the hardware, the higher layers need to know they can consume the cached bytes as well. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: bf537-stamp: move CONFIG_POST handling to COBJS-$(...)Mike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: unify net-related init codeMike Frysinger
Unify all of the net-related init code in the common Blackfin board init code to clean up the ifdef mess a bit. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: fix SWRST/SYSCR register sizesMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Blackfin: update anomaly listsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23Merge branch 'master' of git://git.denx.de/u-boot-avr32Wolfgang Denk
2009-03-23Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk
2009-03-23Merge branch 'evk1100-prep'Haavard Skinnemoen
2009-03-23Merge branch 'mimc200'Haavard Skinnemoen
2009-03-23avr32: fix cacheflush.h location introducted by d8f2aa3298610bJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-23Make flash protection work, when the environment is in EEPROMEric Schumann
On the pcm030 the environment is located in the onboard EEPROM. But we want to handle flash sector protection in a safe manner. So we must read the unlock environment variable from EEPROM instead from flash. This patch is required as long the evironment is saved into the EEPROM. Stefan: Additional change as suggested by Wolfgang, use bigger char array (instead of 4). Signed-off-by: Eric Schumann <E.Schumann@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-23Add define for mpc5200 CDM_CLK_ENAJon Smirl
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
2009-03-22at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22cmc_pu2: fix implicit declaration of function 'eth_setenv_enetaddr'Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22cmc_pu2: fix misc_init_r prototypeJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9xeek: fix soc nameJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move nand drivers to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22atmel/at91/boards: compile dataflash partition only when dataflash isJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move common macb initialisation to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move common usb host initialisation to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move common led management to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move common spi initialisation to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22at91sam9/at91cap: move common serial initialisation to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-21Merge branch 'next' of ../nextWolfgang Denk
2009-03-21Prepare 2009.03Wolfgang Denk
Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-21Replaced endpoint numbers with appropriate macros in usbtty.c.Vivek Kutal
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-03-20UBIFS: Missing offset relocation for compressor 'none'Michael Lawnick
On systems where U-Boot is linked to another address than it really lays (e.g. backup image), calls via function pointers must be fixed with a '+= gd->reloc_off'. This was not done for none_compr in ubifs_compressors_init() what leads to system crash on ubifsmount command. Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de> Acked-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2025-01-01 02:50:32 +0000