summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-08-28TI:am335x: Better comment and organize the networking related optionsTom Rini
While in here, drop CONFIG_BOOTP_DEFAULT as it is unused in the code. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDRTom Rini
After examining both TRMs and doing some experimentation, we can rely on using the start of the download area for CONFIG_SPL_TEXT_BASE and then move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for peripheral boot modes such as UART. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28TI:armv7: Move CONFIG_SPL_LIBDISK_SUPPORT to MMC sectionTom Rini
We only need this library when we're doing "disk" access to MMC/SD. Update comment around the rest of CONFIG_SPL_LIB* to note that the others are always required. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28am33xx: Correct and expand comments on CONFIG_SPL_MAX_SIZETom Rini
We had been allowing the max size to be larger than actually allowed by the ROM. Expand the commentary here to explain why we set these locations. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28ARM: igep00x0.h: Enable raw initrd supportJavier Martinez Canillas
Now that IGEP base boards default environment use the bootz command to boot a zImage instead of a uImage, it makes sense to add support to supply a raw initrd image to the kernel if needed. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
2013-08-28arm: omap3: fix SRAM copy and execution sequenceAlbert ARIBAUD
Fix size calculation in copy of go_to_speed into SRAM. Use SRAM_CLK_CODE in call to SRAM-based go_to_speed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-08-28ARM: OMAP4460: sdp: Limit TPS mux config to 4460Taras Kondratiuk
TPS mux config is 4460 specific, so it should be limited to 4460 only. Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28ARM: OMAP4470: Add Elpida EDB8164B3PF memory configurationLubomir Popov
OMAP4470 SDP SoM has EDB8164B3PF PoP memory on board. This memory has 4Gb x 2CS = 8Gb configuration. Add configuration for runtime calculation and precalculated cases. Patch is based on a draft Lubomir's patch [1]. [1] http://lists.denx.de/pipermail/u-boot/2013-April/150851.html Signed-off-by: Lubomir Popov <lpopov@mm-sol.com> [taras@ti.com: cleaned up patch and fixed precalculated values] Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28ARM: OMAP4470: Add voltage and dpll dataTaras Kondratiuk
OMAP4470 reference design uses TWL6032 PMIC with a following connection scheme: VDD_CORE = TWL6032 SMPS2 VDD_MPU = TWL6032 SMPS1 VDD_IVA = TWL6032 SMPS5 Set voltage and frequency values according to OMAP4470 Data Manual Operating Condition Addendum v0.7 Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28ARM: OMAP4470: Add OMAP4470 identificationTaras Kondratiuk
Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28sdp4430: Initialize board id using CONFIG_MACH_TYPEOleksandr Tyshchenko
Use CONFIG_MACH_TYPE generic macro to set the machine type number in the common arm code instead of setting it in the board code. Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
2013-08-27omap5: Correct include order, drop CONFIG_SYS_PROMPT defineTom Rini
With the new include structure for TI platforms, we need to not define our own CONFIG_SYS_PROMPT and also need to include <configs/omap5_common.h> much sooner, so do both of these. Also drop the unused CONFIG_NET_MULTI Signed-off-by: Tom Rini <trini@ti.com>
2013-08-27Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2013-08-27i2c: fix i2c dev command for not using new frameworkHeiko Schocher
i2c dev command does not work anymore for legacy drivers because a check is executed that is valid only in the new framework. Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Stefano Babic <sbabic@denx.de>
2013-08-26console: usb: kbd: To fix slow TFTP bootingJim Lin
TFTP booting is slow when a USB keyboard is installed and stdin has usbkbd added. This fix is to change Ctrl-C polling for USB keyboard to every second when NET transfer is running. My previous patch is expected to be put into usb_kbd_testc(). But it went into usb_kbd_getc() after applied. This patch is to put change in correct place. Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-08-26console: usb: kbd: To improve TFTP booting performanceJim Lin
TFTP booting is slow when a USB keyboard is installed and stdin has usbkbd added. This fix is to change Ctrl-C polling for USB keyboard to every second when NET transfer is running. Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-08-26NET: Add net_busy_flag if CONFIG_USB_KEYBOARD is definedJim Lin
This flag is to make console aware that NET transfer is running or not. Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-08-26usb: ehci-mx5: Use 'bool' instead of 'unsigned char'Fabio Estevam
The 'enable' argument can be better expressed as boolean. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-26usb: ehci-mx5: Remove unneeded write to cscmr1 registerFabio Estevam
Currently we have the following behavior in ehci_hcd_init() - Read csmr1 register, clear bit 26 and then set bit 26. However a little bit later we call set_usb_phy_clk() which clears bit 26, so let's get rid of the unnecessary code. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-08-26usb:dfu:g_dnl: Refactoring the string definition code for g_dnl driverLukasz Majewski
The manufacturer and product IDs are dynamically assigned when gadget is bind. Now the IDs aren't assigned at struct g_dnl_string_defs definition. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: "Egli, Samuel" <samuel.egli@siemens.com>
2013-08-26usb:dfu:g_dnl: Change number of exported configurations at composite gadgetLukasz Majewski
USB composite gadget (g_dnl) supports only one configuration. Due to that the corresponding field - bConfigurationValue has been changed. Moreover more descriptive names were chosen for relevant fields. Windows XP setup: - Thesyscon USB Descriptor Dumper - zadig_xp program for WinUSB installation (which is required by dfu-util) - dfu-util for windows (version 0.6) - TRATS target connected via USB hub to test Win XP machine. Tested at: Trats - Exynos4210 Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: "Egli, Samuel" <samuel.egli@siemens.com>
2013-08-26dfu, nand, ubi: add partubi alt settings for updating ubi partitionHeiko Schocher
updating an ubi partition needs a completely erased mtd partition, see: http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html So, add partubi alt setting for the dfu_alt_info environment variable to mark this partition as an ubi partition. In case we update an ubi partition, we erase after flashing the image into the partition, the remaining sektors. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@ti.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Scott Wood <scottwood@freescale.com>
2013-08-26usb: Use well-known descriptor sizes when parsing configurationJulius Werner
The existing USB configuration parsing code relies on the descriptors' own length values when reading through the configuration blob. Since the size of those descriptors is always well-defined, we should rather use the known sizes instead of trusting device-provided values to be correct. Also adds some safety to potential out-of-order descriptors. Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090 Signed-off-by: Julius Werner <jwerner@chromium.org>
2013-08-26ARM: OMAP5-uevm: Add usb device reset APIDan Murphy
Add the call back to reset the LAN9730 after the FEAT_POWER has been called. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26USB: usb-hub: Add a weak function for resetting devicesDan Murphy
Add a __weak function that can be overridden to reset devices attached to an ehci devices after the FEAT_POWER has been submitted Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26ARM: OMAP5-uevm: Add USB MAC ethernet addressDan Murphy
Set the usbethaddr based on the OMAP DIE_ID registers which should be unique for each processor. Then set this as the usb ethernet MAC address. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26ARM: OMAP5-uevm: Add USB ehci support for the uEVMDan Murphy
Add the USB ehci support for the OMAP5 uEVM. Configure the uEVM mux data Add the flags to build the appropriate modules Add the usb call backs to initialize the EHCI controller Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26ARM: OMAP: USB: Fix linker error when ULPI is not definedDan Murphy
Fix the linker error for missing ulpi_reset when ulpi is not defined in the board config. Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Marek Vasut <marex@denx.de>
2013-08-26ARM: OMAP5: USB: Add OMAP5 common USB EHCI informationDan Murphy
* Enable the OMAP5 EHCI host clocks * Add OMAP5 EHCI register definitions * Add OMAP5 ES2 host revision Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26omap5: uevm: Change the board name to correct nameDan Murphy
Change the board name for the sys info to 5432 uEVM Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Marek Vasut <marex@denx.de>
2013-08-23mmc: mxsmmc: Enable MMC HC supportAmaury Pouly
Enable support for high-capacity eMMC and MMC cards. The MXS MMC driver has no problem with those. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com> Cc: Andy Fleming <afleming@freescale.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-22env_nand.c: support falling back to redundant env when writingPhil Sutter
Without this patch, when the currently chosen environment to be written has bad blocks, saveenv fails completely. Instead, when there is redundant environment fall back to the other copy. Environment reading needs no adjustment, as the fallback logic for incomplete writes applies to this case as well. Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
2013-08-22nand_util: delete a useless variableMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: Do not show usage when scrub is abortedMasahiro Yamada
When executing nand scrub, the user gets the prompt: Really scrub this NAND flash? <y/N> We do not want the annoying usage displayed when saying N here. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: slight optimization of nand_dump functionMasahiro Yamada
If a non-zero value is given to only_oob argument, printing the main area is skipped. With a little modification, we can skip the whole while loop. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: fix a memory leak in nand_dump functionMasahiro Yamada
If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize); succeeds and oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize); fails, nand_dump function should free databuf. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22arm: atmel: cpux9k2: board update and enhancementJens Scharsig (BuS Elektronik)
- fix adresses in env settings in config header - add missing CONFIG_STANDALONE_LOAD_ADDR to eb_cpux9k2 config header - remove jffs2 support, board doesn't use this anymore - add ubifs support - change sizes and start for partitions Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: add copyright and remove error header infoBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Jens Scharsig <js_at_ng@scharsoft.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: add gpio common API supportBo Shen
add gpio common API support for gpio command Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix unnecessary cast] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: fix code to use pointer for pio portBo Shen
fix code to use pointer for pio port as the warning message suggested remove the warning message Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: remove the config.mk fileBo Shen
remove the config.mk file move text base define to board config file for following boards - at91sam9m10g45ek - at91sam9x5ek Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: sama5d3: fix typo error for CONFIG_ENV_IS_NOWHEREBo Shen
fix typo error for CONFIG_ENV_IS_NOWHERE from CONIG_ENV_IS_NOWHERE Signed-off-by: Bo Shen <voice.shen@gmail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: sama5d3: remove unused defineBo Shen
The CONFIG_MAX_NAND_CHIPS never used, remove it No where define LCD_TEST_PATTERN, so no need undefine Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: sama5d3: fix smc cs related registers offsetBo Shen
the smc cs related registers start at 0x600 and loop with 5 registers so the reserved register should be in at91_smc structure while no in at91_cs structure. So fix it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: atmel_nand: add code to check the ONFI parameter ECC requirementWu, Josh
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's ecc minimum requirement in ONFI parameter. a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it. Driver will display a WARNING if the values are different from ONFI parameters. b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use the value from ONFI parameters. * If ONFI ECC parameters are in ONFI extended parameter page, since we are not support it, so assume the minimum ecc requirement is 2 bits in 512 bytes. * For non-ONFI support nand flash, also assume the minimum ecc requirement is 2 bits in 512 bytes. 2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP and CONFIG_PMECC_SECTOR_SIZE. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22mtd: atmel_nand: alloc memory instead of use static array for pmecc dataWu, Josh
In this way, the pmecc corraction capbility can change in run time. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22linux/compat.h: move dev_err, dev_info and dev_dbg from usb driver to compat.hWu, Josh
Since kernel code current use many dev_xxx() instead of using printk. To compatible, move those dev_xxx from usb driver to linux/compat.h. Then all driver code can use dev_err, dev_info and dev_vdbg. This patch also removed duplicated macro definitions in usb driver. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: sama5d3: remove unused definition about PMECC alpha table offsetWu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: atmel_nand: pmecc driver will select the galois table by sector sizeWu, Josh
Define the galois index table offset in chip head file. So user do not need to set by himself. Driver will set it correctly according to sector_size. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> [rebased on master] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: add nand trimffs subcommand for at91sam9n12 and at91sam9x5Bo Shen
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot to flash the rootfs, in order to avoid flash one sector with all 0xff into NAND, so use nand trimffs subcommand to avoid it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
generated by cgit (git 2.34.1) at 2024-12-28 12:59:33 +0000