summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-03-14igep00x0: fixup FDT according to detected flash typeLadislav Michl
Leave only detected flash type enabled in FTD as otherwise GPMC CS is claimed (and never freed) by Linux, causing 'concurent' flash type not to be probed. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2017-03-14igep00x0: disable environmentLadislav Michl
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we switched to 8bit ECC to fullfill flash specification requirements. However when trying to run U-Boot on board with 1bit ECC'd data on flash, UBI code takes several minutes to pass scan as reading of every block ends with ecc error (which is also printed on console). So, until proper solution is developed, disable environment alltogether. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2017-03-14board: Add STMicroelectronics STiH410-B2260 supportPatrice Chotard
This is a 96Board compliant board based on STiH410 SoC: - 1GB DDR - On-Board USB combo WiFi/Bluetooth RTL8723BU with PCB soldered antenna - Ethernet 1000-BaseT - SATA - HDMI - 2 x USB2.0 type A - 1 x USB2.0 type micro-AB - SD card slot - High speed connector (SD/I2C/USB interfaces) - Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces) Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410-B2260: Add device treePatrice Chotard
This device tree has been extracted from v4.9 kernel Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410: Add STi pinctrl driverPatrice Chotard
Add STMicroelectronics STiH410 pinctrl driver Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410: Add STi SDHCI driverPatrice Chotard
Add SDHCI host controller found on STMicroelectronics SoCs On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live inside a dedicated flashSS sub-system that provides an extend subset of registers that can be used to configure the Arasan MMC/SD Host Controller. This means, that the SDHCI Arasan Controller can be configured to be eMMC4.5 or 4.3 spec compliant. W/o these settings the SDHCI will configure and use the MMC/SD controller with limited features e.g. PIO mode, no DMA, no HS etc. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-03-14gpio: do not include <asm/arch/gpio.h> for ARCH_STIPatrice Chotard
As no gpio.h is defined in arch/arm/include/asm/arch-stih410, to avoid compilation failure, do not include asm/arch/gpio.h. This is needed for example when including sdhci.h, which include asm/gpio.h>. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410: Add STi serial driverPatrice Chotard
This patch adds support to ASC (asynchronous serial controller) driver, which is basically a standard serial driver. This IP is common across other STMicroelectronics SoCs Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410: Add STi sysreset driverPatrice Chotard
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14STiH410: Add STi timer driverPatrice Chotard
Add ARM global timer based timer Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14arm: Add support for STMicroelectronics STiH410 socPatrice Chotard
The STiH410 is an advanced multi-HD AVC processor with 3D graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU part of the STiH407 family. It has wide connectivity including USB 3.0, PCI-e, SATA and gigabit ethernet. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-03-14armv7m: Add SysTick timer driverPhil Edworthy
The SysTick is a 24-bit down counter that is found on all ARM Cortex M3, M4, M7 devices and is always located at a fixed address. The number of reference clock ticks that correspond to 10ms is normally defined in the SysTick Calibration register's TENMS field. However, on some devices this is wrong, so this driver allows the clock rate to be defined using CONFIG_SYS_HZ_CLOCK. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-03-14tools: omapimage: Fix size in headerLokesh Vutla
The size field in GP header that is expected by ROM is size of the image + size of the header. But omapimage generates a gp header only with size of the image as size field. Fix it Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-03-14arm: omap3: Bring back ARM errata workaround 725233Siarhei Siamashka
The workaround for ARM errata 725233 had been lost since commit 45bf05854bc94e (armv7: adapt omap3 to the new cache maintenance framework). Bring it back in order to avoid very difficult to reproduce, but actually encountered in the wild CPU deadlocks when running software rendered X11 desktop on OMAP3530 hardware. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Migrate to Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-14arm: omap3: Compile clock.c with -marm option to unbreak OMAP3530Siarhei Siamashka
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c26d5 ("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)") because it enabled the use of Thumb2 for the SPL. Experiments have shown that the deadlock happens in the prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'. This patch enforces the compilation of clock.c source file in ARM mode and makes the deadlock disappear. We are yet to figure out the root cause of the problem. Still this is somewhat better than having non-bootable boards for years. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-14omap3_overo: Reduce SPL sizeTom Rini
Borrowing from omap3_logic, switch to SPL_SYS_MALLOC_SIMPLE and moving the stack to DDR as soon as we're able. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-14ARM: dts: uniphier: more re-sync DT with LinuxMasahiro Yamada
For better maintainability. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-03-14ARM: dts: uniphier: fix no unit name warningsMasahiro Yamada
Fix warnings reported when built with W=1, by DTC 1.4.2 or later: Node /memory has a reg or ranges property, but no unit name Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-03-14ARM: dts: uniphier: remove skeleton.dtsi inclusionMasahiro Yamada
Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated") declared that skeleton.dtsi was deprecated. Move the memory node below to suppress warnings of FDTGREP. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-03-14ARM: uniphier: set DRAM_SPARSE flag for LD21 boardsMasahiro Yamada
Commit 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from board parameters") accidentally unset the DRAM_SPARSE flag, and changed the physical map of the DRAM channels. Revive the original behavior. Fixes: 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from board parameters") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Shunji Sato <sato.shunji@socionext.com>
2017-03-13Prepare v2017.03Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13scripts/config_whitelist.txt: RegenerateTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-13configs: Re-syncTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-11arm: omap-common: Fix typo in CONFIG_OMAP54XX guardMatthijs van Duin
Some initialization was unintentionally being skipped on omap5. Fixes: f5af0827f276 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX") Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-11tools: binman: change shebang from python into python2Jörg Krause
This tool does not work with Python 3. Change the shebang to make sure the script is run by a Python 2 interpreter. Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-03-11arm: OMAP2+: nandecc: propagate error to command return statusLadislav Michl
Currently nandecc returns zero even if underlaying omap_nand_switch_ecc function fails. Fix that by propagating error returned to command return value. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-09Merge branch 'pmic' of git://git.denx.de/u-boot-mmcTom Rini
2017-03-09ARM: Migrate errata to KconfigTom Rini
This moves all of the current ARM errata from various header files and in to Kconfig. This allows for a minor amount of cleanup as we had some instances where both a general common header file was enabling errata as well as the board config. We now just select these once at the higher level in Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09omap4: Migrate to using implyTom Rini
Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be using imply instead in arch/arm/Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09omap3: Migrate to using implyTom Rini
Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be using imply instead in arch/arm/Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09TI: Migrate board/ti/common/Kconfig to implyTom Rini
The option that we had set in board/ti/common/Kconfig as default y are best done with imply under the appropriate main Kconfig option instead. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09am335x_evm: Switch to using imply keywordTom Rini
These particular SPL options are part of what the ROM provides, but for compatibility with how we have previously used them, move them to being implied by the board being selected. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09kconfiglib.py: Kludge in 'imply' supportTom Rini
Currently upstream does not yet understand the imply keyword. For what we use kconfiglib.py for today, this is OK. We only need to be able to evaluate in order to make boards.cfg and none of those choices will depend on how imply evaluates out. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09do_smhload: fix return codeRyan Harkin
do_smhload was using a ulong to store the return value from smh_load_file. That returns an int, where -1 indicates an error. As a ulong will never be negative, smh_load_file errors were not detected and so_smhload always returned zero. Also, when errors were spotted, do_smhload was returning 1, rather than the enumeration CMD_RET_FAILURE (which is also 1). Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-09Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigsTom Rini
In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09tools: Remove CONFIG_SYS_TEXT_BASE in MakefilePatrick Delaunay
This define is not used in tools sources and can be removed to avoid unnecessary link between tools and defconfig Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-09kbuild: turn of dtc unit address warnings by defaultMasahiro Yamada
DTC 1.4.2 or later checks DT unit-address without reg property and vice-versa, and generates lots of warnings. Fixing DT files will take for a while. Until then, let's turn off the check unless building with W=*. Introduce a new helper dtc-option to check if the option is supported in order to suppress warnings on older versions. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2017-03-09sunxi: power: axp809.c: Fix aldo1-2 being disabled for mvolt != 0Rask Ingemann Lambertsen
The execution flow is currently like this for aldo_num == 1 or 2: int axp_set_aldo(int aldo_num, unsigned int mvolt) { ... if (mvolt == 0) return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1, AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1)); ... return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1, AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1)); } I.e. aldo1 and aldo2 will always be disabled. This patch fixes it by setting (rather than clearing) the enable bit when mvolt != 0. Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk> Fixes: 795857df413a ("sunxi: power: add AXP809 support")
2017-03-08Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2017-03-08Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2017-03-08omap3_logic: Move SPL Stack into SDRAMAdam Ford
A previous patch broke the board. This patch will add missing part from the previous patch and also move the SPL Stack into SDRAM at 0x82000000. Tested with GCC 4.8.2 and GCC 6.2 Fixes: 0959649dc6d9 ("omap3_logic: Switch to simple malloco in SPL") Signed-off-by: Adam Ford <aford173@gmail.com> Changes in V2: - Keep CONFIG_SPL_SYS_MALLOC_SIMPLE - Add CONFIG_SYS_MALLOC_F_LEN=0x2000 (8 MB)
2017-03-07video: cfb_console: fix 32-bit display on 64-bit architecturesAndre Przywara
"unsigned long" is a lousy data type when it comes to match peripheral hardware registers with a fixed size. Just do the obvious and match a 32-bit display format with an "u32" data type for casting. This fixes the logo display on 64-bit architectures, which produced a black line on the right side of the logo with non-black backgrounds. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2017-03-07net: zynq_gem: Fix masking of supported phydev featuresNathan Rossi
When the zynq_gem driver initializes the phy it sets the supported features that the phy can support and advertise. However instead of masking the supported features such that it limits the available features it sets the phy to have the exact supported features of the zynq_gem. This is problematic as it will enable features that a phy does not have or cannot advertise. Specifically this appears as an issue when using a phy that is only capable of 10/100, but the zynq_gem driver will override this and try to enable and advertise 10/100/1000. Reported-by: Arno Steffens <star@gmx.li> Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN") Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Tested-by: Arno Steffens <star@gmx.li> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2017-03-01net: macb: Fix ETH not found when clock not supportWenyou Yang
For the boards such as smartweb on which the clock driver isn't supported, the ethernet fail to be found when booting up with the below log. ---8<--- Net: No ethernet found. --->8--- Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-01armv8: spl: Call spl_relocate_stack_gd for ARMv8Philipp Tomsich
As part of the startup process for boards using the SPL, we need to call spl_relocate_stack_gd. This is needed to set up malloc with its DRAM buffer. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-01armv5te: make 'ret lr' produce iinterworking 'bx lr'Albert ARIBAUD
Current ARM assembler helper for the 'return to caller' pseudo-instruction turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain in its current ARM state even when the routine doing the 'ret' was called from Thumb-1 state, triggering an undefined instruction exception. This causes early run-time failures in all boards compiled using the Thumb-1 instruction set (for instance the Open-RD family). ARMv5TE supports 'bx lr' which properly implements interworking and thus correctly returns to Thumb-1 state from ARM state. This change makes 'ret lr' turn into 'bx lr' for ARMv5TE. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2017-02-27Prepare v2017-rc3Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-27arm: mach-omap2: Flush cache after FIT post-processing imageAndrew F. Davis
After we authenticate/decrypt an image we need to flush the caches as they may still contain bits of the encrypted image. This will cause failures if we attempt to jump to this image. Reported-by: Yogesh Siraswar<yogeshs@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-27drivers/net/Kconfig: Correct use of apostropheTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-27Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini