summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-10-02rockchip: rk3188: explicitly set vcc_sd0 pin to gpio on rk3188-radxarockHeiko Stuebner
It is good practice to make the setting of gpio-pinctrls explicitly in the devicetree, and in this case even necessary. Rockchip boards start with iomux settings set to gpio for most pins and while the linux pinctrl driver also implicitly sets the gpio function if a pin is requested as gpio that is not necessarily true for other drivers. The issue in question stems from uboot, where the sdmmc_pwr pin is set to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage loader. The regulator controlled by the pin is active-low though, so when the dwmmc hw-block sets its enabled bit, it actually disables the regulator. By changing the pin back to gpio we fix that behaviour. [picked from the identical linux patch https://patchwork.kernel.org/patch/10609253/] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02rockchip: rk3188: add u-boot-specific mmc propertiesHeiko Stuebner
The dwmmc controllers on rk3188 do not have idma support, so need to use the fifo-mode and it my tests they became confused and stopped working if the frequency was to high. While I only tested in somewhat bigger steps, 32MHz for example hung the controller, while reducing it to 16MHz worked just fine and is reasonably fast to load a kernel from mmc. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02rockchip: dwmmc: add rk2928-dw-mshc compatibleHeiko Stuebner
The rk3188 works nicely with the rockchip mmc driver, so we just need to add the different compatible for it - as used in the Linux kernel. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02mmc: dw_mmc: check fifo status with a timeout in fifo modeHeiko Stuebner
While trying to enable the dw_mmc on rk3188 I managed to confuse and hang the dw_mmc controller into not delivering further data. The fifo state never became ready and the driver was iterating in the while loop reading 0-byte packets forever. So inspired by how other implementations handle this, check the fifo- state beforhand and add a timeout to catch any glaring fifo issues without hanging uboot altogether. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-01Prepare v2018.11-rc1Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-01MAINTAINERS: at91: update entry for at91 boardsEugen Hristev
Updated the maintainership for the at91 boards. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-30Merge git://git.denx.de/u-boot-dmTom Rini
2018-09-30MAINTAINERS: Update some entries for missed boardsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-30fs: btrfs: Fix cache alignment bugsMarek Vasut
The btrfs implementation passes cache-unaligned buffers into the block layer, which triggers cache alignment problems down in the block device drivers. Align the buffers to prevent this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Behun <marek.behun@nic.cz>
2018-09-30usb:ci_udc: don't overwrite configuration on pullupRamon Fried
change writel to writebits32 in ci_pullup() in order to keep phy configuration in tact. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30db410c: automatically launch fastbootRamon Fried
If during boot the key-vol-down press is detected we'll fall back to fastboot. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30DB410c: Enable fastboot supportRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30usb: ehci-msm: Add init_after_reset for CI_UDCRamon Fried
MSM uses the chipidea controller IP, however it requires to reinit the phy after controller reset. in EHCI mode there's a dedicated callback for it. In device mode however there's no such callback. Add implementaion of ci_init_after_reset() to implement the above requirement in case CI_UDC driver is used. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30usb:ci_udc: Introduce init_after_reset phy functionRamon Fried
MSM variant of Chipidea must reinitalize the phy after controller reset. Introduce ci_init_after_reset() weak function that can be used to achieve the above init. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30ehci: msm: use init_type in probeRamon Fried
Change ehci_usb_probe() function to initialize the USB according to the init_type provided. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30ehci: msm: switch to generic PHY uclassRamon Fried
All the underlying USB PHY was handled in the ehci driver. Use the generic phy API instead. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30configs: db410c: Enable USB PHYRamon Fried
Enable USB PHY driver. Also fixed the alphabetically ordering of the config. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30dts: db410c: Add bindings for MSM USB phyRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30phy: db410c: Add MSM USB PHY driverRamon Fried
Add a PHY driver for the Qualcomm dragonboard 410c which allows switching on/off and resetting the phy connected to the EHCI controllers and USBHS controller. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30db410c: serial# env using msm board serialRamon Fried
The serial# environment variable needs to be defined so it will be used by fastboot as serial for the endpoint descriptor. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30dts: db410c: add alias for USBRamon Fried
Alias is required so req-seq will be filled. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30ehci: msm: Add missing platdataRamon Fried
platdata_auto_alloc_size was not initialized in structure. Caused null pointer dereference when configuring device as gadget. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30ehci: Replace board_prepare_usb with board_usb_initRamon Fried
Use standard board_usb_init() instead of the specific board_prepare_usb. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30serial: serial_stm32: Enable uart FIFO for STM32F7xx SoCsPatrice Chotard
Since commit 7b3b74d32127 ("serial: serial_stm32: Enable overrun") on STM32F7xx based boards, the first lines of serial output are missing during boot (we no more see the U-Boot release version, board model and DRAM size). By enabling the uart FIFO on STM32F7, the complete U-boot log can be sent correctly. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-30u-boot: align cache flushes in load_elf_image_shdr to line boundariesNeil Stainton
Prevent cache warning messages when using the 'bootelf' command on an Arm target. Round down each section start address and round up the respective section end to the nearest cache line. Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk> [trini: Manually apply, rework whitespace] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-30kbuild: fix # escaping in appending U-Boot own DTMasahiro Yamada
The escape sequence '\#' does not work for the latest GNU Make from the git tree. Replace it with $(pound) as Linux did. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-30Kbuild: fix # escaping in .cmd files for future MakeRasmus Villemoes
[ commit 9564a8cf422d7b58f6e857e3546d346fa970191e in Linux ] I tried building using a freshly built Make (4.2.1-69-g8a731d1), but already the objtool build broke with orc_dump.c: In function ‘orc_dump’: orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations] if (elf_getshdrnum(elf, &nr_sections)) { Turns out that with that new Make, the backslash was not removed, so cpp didn't see a #include directive, grep found nothing, and -DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS. Now, that new Make behaviour is documented in their NEWS file: * WARNING: Backward-incompatibility! Number signs (#) appearing inside a macro reference or function invocation no longer introduce comments and should not be escaped with backslashes: thus a call such as: foo := $(shell echo '#') is legal. Previously the number sign needed to be escaped, for example: foo := $(shell echo '\#') Now this latter will resolve to "\#". If you want to write makefiles portable to both versions, assign the number sign to a variable: C := \# foo := $(shell echo '$C') This was claimed to be fixed in 3.81, but wasn't, for some reason. To detect this change search for 'nocomment' in the .FEATURES variable. This also fixes up the two make-cmd instances to replace # with $(pound) rather than with \#. There might very well be other places that need similar fixup in preparation for whatever future Make release contains the above change, but at least this builds an x86_64 defconfig with the new make. Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847 Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-30spl: mmc: Report device number when we failAlex Kiernan
If we fail to find the MMC boot device, report the number of the one we were looking for in the error to aid diagnosis. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-09-30clk: Add support for Arm's Versatile Express OSC clock generatorsLiviu Dudau
The Arm Versatile Express and Juno development boards contain an OSC clock generator that can be accessed through the Versatile Express config bus. The generators are quite often being controlled by some MCU and the config bus offers a uniform way of exposing them. Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2018-09-30cmd: env: Fix CRC calculation for 'env export -c -s'Neil Stainton
Fix failure to reimport exported checksummed, size constrained data block. 'env export -c' command ignores optional -s size argument when calculating checksum causing subsequent 'env import -c' to fail. Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
2018-09-29Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-29dm: test: Add "/firmware" node scan testRajan Vaja
Add a test which verifies that all subnodes under "/firmware" nodes are scanned. Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile, updated #if condition in drivers/firmware/firmware-uclass.c: Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29firmware: Add FIRMWARE config prompt stringRajan Vaja
There is no prompt string for FIRMWARE config. Without this, FIRMWARE config cannot be enabled through menuconfing or config file. Fix this by adding prompt summary. Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-29sandbox: Add an explanation of the sandbox variantsSimon Glass
There are quite a few builds of sandbox now. Add information about these to the README. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29buildman: Avoid hanging when the config changesSimon Glass
Something has changed in the last several month such that when buildman builds U-Boot incrementally and a new CONFIG option has been added to the Kconfig, the build hanges waiting for input: Test new config (NEW_CONFIG) [N/y/?] (NEW) Since binamn does not connect the build's stdin to anything this waits on stdin to the build thread, which never comes. Eventually I suspect all the threads end up in this state and the build does not progress. Fix this by passing /dev/null as input to the build. That way, if there is a new CONFIG, the build will stop (and fail): Test new config (NEW_CONFIG) [N/y/?] (NEW) Error in reading or end of file. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29include/dm.h: Remove duplicated include directiveLiviu Dudau
Remove duplicated inclusion of dm/ofnode.h Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Drop period at end of commit subject: Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29include/clk.h: Fix the name of the clock uclass in commentLiviu Dudau
The comment references a structure name that doesn't exist. Use the name of the actual uclass. Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Drop period at end of commit subject: Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29fdt: fdtdec_setup_memory_banksize() use livetreeJens Wiklander
Converts fdtdec_setup_memory_banksize() to use ofnode functions instead. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2018-09-29cmd: clk: Add trivial implementation of clock dump for DMMarek Vasut
Add trivial implementation of the clk dump in case DM is enabled. This implementation just iterates over all the clock registered with the CLK uclass and prints their rate. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-09-29test: Add tests for board uclassMario Six
Add tests for the new board uclass. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-09-29board: Add gazerbeam driverMario Six
Add a board driver for the upcoming gdsys Gazerbeam board. Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-29drivers: Add board uclassMario Six
Since there is no canonical "board device" that can be used in board files, it is difficult to use DM function for board initialization in these cases. Hence, add a uclass that implements a simple "board device", which can hold devices not suitable anywhere else in the device tree, and is also able to read encoded information, e.g. hard-wired GPIOs on a GPIO expander, read-only memory ICs, etc. that carry information about the hardware. The devices of this uclass expose methods to read generic data types (integers, strings, booleans) to encode the information provided by the hardware. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-09-29test: Add tests for dev_{enable, disable}_by_pathMario Six
Add tests for the dev_{enable,disable}_by_path functions. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-09-29core: Add dev_{disable,enable}_by_pathMario Six
We cannot use device structures to disable devices, since getting them with the API functions would bind and activate the device, which would fail if the underlying device does not exist. Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-29test: Add tests for DT-manipulation functionsMario Six
Add tests for the ofnode_set_enabled, ofnode_write_string, and ofnode_write_property functions. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-09-29core: Add functions to set properties in live-treeMario Six
Implement a set of functions to manipulate properties in a live device tree: * ofnode_write_prop() to set generic properties of a node * ofnode_write_string() to set string properties of a node * ofnode_set_enabled() to either enable or disable a node Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-29binman: Allow writing a map file when something goes wrongSimon Glass
When we get a problem like overlapping regions it is sometimes hard to figure what what is going on. At present we don't write the map file in this case. However the file does provide useful information. Catch any packing errors and write a map file (if enabled with -m) to aid debugging. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29binman: Support ELF files for U-Boot and SPLSimon Glass
For sandbox we want to put ELF files in the image since that is what we need to execute. Add support for this. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29binman: Correct fmap output on x86Simon Glass
Normally x86 platforms use the end-at-4gb option. This currently produces an FMAP with positions which have a large offset. The use of end-at-4gb is a useful convenience within binman, but we don't really want to export a map with these offsets. Fix this by subtracting the 'skip at start' parameter. Also put the code which convers names to fmap format, for clarity. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29binman: Record the parent section of each sectionSimon Glass
At present sections have no record of their parent so it is not possible to traverse up the tree to the root and figure out the position of a section within the image. Change the constructor to record this information. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-28 12:42:45 +0000