summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-04-11i2c: fsl: Add option to get clock from DTMario Six
Add an option to get the clock speed from the device tree, hence adding compatibility with DM clock drivers. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-11i2c: fsl: Use dev_read_addrMario Six
Since bus translations are now fully supported, use a plain "dev_read_addr" to get the device address from the device tree. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-11i2c: ihs_i2c: Use new fpgamap interfaceMario Six
The fpgamap interface has been switched to a "single function + data size" interface. Reflect this change in the IHS I2C driver. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-11dm: i2c: implement gpio-based I2C deblockAlexander Kochetkov
The commit implement a gpio-based software deblocking. The code extract I2C pins description from device tree, switch pins to GPIO mode, toggle SCL until slave release SDA, send I2C stop and switch I2C pins back to I2C mode. Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
2018-04-11dm: i2c: dts: Add gpios and pinctrl device tree propertiesAlexander Kochetkov
The commit describe usage of gpios and pinctrl device tree properties in order to enable gpio-based software deblocking. Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
2018-04-09Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.05-rc2 - Various DT changes and sync with mainline kernel - Various defconfig updates - Add SPL init for zcu102 revA - Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX and zc1751-dc3 - Net fixes - xlnx,phy-type - 64bit axi ethernet support - arasan: Fix nand write issue - fpga fixes - Maintainer file updates
2018-04-09Merge tag 'signed-efi-next' of git://github.com/agraf/u-bootTom Rini
Patch queue for efi - 2018-04-09 Highlights this time around: - Lots of minor spec compliance fixes - Support full range of GOP BLT commands - More fine grained error checking - Network fixes (init, DP) - Lots of other bug fixes...
2018-04-09arm64: zynqmp: Add support for Xilinx zcu111-revAMichal Simek
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for Xilinx zcu106-revAMichal Simek
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu104 customer boardMichal Simek
Xilinx zcu104 is another customer board. It is sort of zcu102 clone with some differences. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc12xx boardsMichal Simek
Add support for zc12xx boards. All of them are internal boards for silicon validation and share very similar base platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc1751 dc3Michal Simek
zc1751 is based board with dc3 extenstion card which is used for silicon validation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu100 aka Ultra96 boardMichal Simek
Add support for Xilinx zcu100. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Get 200MHz clock early for MMCMichal Simek
SPL MMC boot requires to have clock early. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove pinctrl settingsMichal Simek
This part hasn't been pushed to mainline yet that's why remove it. The patch can be reverted in future when this is pushed there. Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-04-09arm64: zynqmp: Remove power domain descriptionMichal Simek
This part hasn't been pushed to mainline yet that's why remove it. The patch can be reverted in future when this is pushed there. Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-04-09arm64: zynqmp: Add low level initialization for zc1751Michal Simek
Add psu init for zc1751 dc cards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add low level initialization for zcu102-revAMichal Simek
Add psu init for zcu102-revA. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable Fixed link supportMichal Simek
This patch enables the fixed link support for all ZynqMP boards. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable mac address randomization for zc1751 dc5Michal Simek
There is no memory which stores mac address that's why generate it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable ethernet phys for zc1751 dc5Michal Simek
Enable ethernet phys for zc1751 dc5. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable booting to ATFLuca Ceresoli
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which pass control to full u-boot(EL2). This has been tested on zcu106, so enable it in this defconfig. To generate an image that triggers this booting flow, you need to pass '-O arm-trusted-firmware' to mkimage. Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable pxe and dhcp if commands are enabledMichal Simek
Targets without net can't use pxe or dhcp boot methods. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09net: phy: xilinx_phy: Read phytype using property xlnx,phy-typeSiva Durga Prasad Paladugu
This patch reads phytype from property "xlnx,phy-type" instead od simply looking for "phy-type". This is to be inline with Linux and also fixes the issue of detecting it wrongly in u-boot. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09axi: ethernet: Added support for 64 bit addressing for axi-ethernetVipul Kumar
This patch uses writeq() function to enable greater than 32 bit addressing of axi-ethernet for the ZynqMP devices. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09nand: arasan_nfc: Fixed NAND write issueVipul Kumar
In commit 2453c695185f ("arm64: zynqmp: nand: Fixed NAND erase issue for size 1GiB or more"), ARASAN_NAND_MEM_ADDR1_PAGE_MASK macro changed to 0xFFFF and the same macro is used in nand write and so that getting nand write error. This patch reverted this macro to the 0xFFFF0000 and used ARASAN_NAND_MEM_ADDR1_COL_MASK in the nand erase function which is equal to 0xFFFF. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynq: Add delay after PCFG_PROG_B changeSiva Durga Prasad Paladugu
There is delay needed after PCFG_PROGB change if AES key source is efuse. This fixes the issue of encrypted bitstream loading with AES efuse as key source. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynqmp: Fix the nonsecure bitstream loading issueSiva Durga Prasad Paladugu
Xilfpga library expects the size of bitstream in a pointer but currenly we are passing the size as a value. This patch fixes this issue. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09fpga: zynqmp: Update zynqmp_load() as per latest xilfpgaSiva Durga Prasad Paladugu
Latest xilfpga expects to set BIT5 of flags for nonsecure bitsream and also expects length in bytes instead of words This patch does the same. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09fpga: zynqmp: Add support to get the PCAP status for fpga info commandNitin Jain
This patch adds support for ZynqMP platform to print FPGA PCAP status for "fpga status" command. Signed-off-by: Nitin Jain <nitinj@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09clk: zynqmp: Add new compatible string for clock driverMichal Simek
New and old clk drivers are sharing IDs and descriptions. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Use fixed partitions for spi flash for zc770 xm010Michal Simek
Sync with mainline. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Fix eeprom dt nodesMichal Simek
- Use eeprom for node name - Use atmel compatible string instead of at. - Add missing labels Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09ARM: dts: zynq: Add generic compatible string for I2C EEPROMJavier Martinez Canillas
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Use i2c-mux instead of i2cswitch for pca9548Michal Simek
i2c muxes should described like this. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Sync up licenses with mainline kernelMichal Simek
Use different location for SPDX line. Also update dates for new mainline DTS files. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm: zynq: Remove 0x prefixes from cc108Michal Simek
The patch fixing issues reported by DTC: zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0x400000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0x800000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xc00000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xd00000 unit name should not have leading "0x" zynq-cc108.dtb: Warning (unit_address_format): Node /amba/spi@e000d000/flash@0/partition@0xf00000 unit name should not have leading "0x" Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove double spaces from dts fileMichal Simek
There is no reason to have double spaces for indentation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add silabs prefix to u69 for zcu102Michal Simek
Add vendor prefix to si5341. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove number from clock-generator node nameMichal Simek
There shouldn't be a number appended based on spec. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove u-boot commands from dts filesMichal Simek
U-Boot commands shouldn't be the part of kernel DTS files. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Update sd properties for dc5Srinivas Goud
This patch adds no-1-8-v below properties to sd node for dc5 board dts. Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Enable ttcs for zc1751 dc5Michal Simek
Enable TTCs for this target as is done in Linux kernel. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add eeprom reference to eeprom nodesMichal Simek
eeprom can contain information which can be used by nvmem drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use atmel prefix instead of atMichal Simek
This changes was done in mainline and this patch is just following it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Fix spi flash partition definition for zc1751 dc2Michal Simek
Using different node name and label partitions as data. Also use latest compatible strings based on mainline review. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use s/_/-/g in node name for zcu102 rev1.0Michal Simek
Follow spec for node names. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Use keycode from input/input.hMichal Simek
Instead of hardcoding numbers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Remove additional comments from dts filesMichal Simek
Remove additional comments which were removed as the part of upstreaming. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Sync up license with mainline kernelMichal Simek
Mainline Linux kernel has adopted SPDX header license in a different format then was used before. This patch is syncing it up. Also update years in License text and remove Nathalie's email because it is no longer valid. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-29 15:59:02 +0000