| Age | Commit message (Expand) | Author |
|---|
| 2016-06-10 | configs: ls2080a: Increase load image len in NAND boot | Yuan Yao |
| 2016-06-10 | armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND boot | Yuan Yao |
| 2016-06-10 | dts: ls2080aqds: Add QSPI dts node | Yuan Yao |
| 2016-06-10 | configs: ls2080aqds: Enable QSPI flash support | Yuan Yao |
| 2016-06-10 | armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enable | Yuan Yao |
| 2016-06-10 | configs: ls2080a_common: Remove duplicate NOR configs | Yuan Yao |
| 2016-06-10 | armv8: ls2080aqds: Select QSPI CLK div via SCFG | Yuan Yao |
| 2016-06-10 | drivers: i2c: mxc: Add early init | Yuan Yao |
| 2016-06-10 | board: ls2080a: Add "mcinitcmd" env for MC & DPL deployment | Pratiyush Mohan Srivastava |
| 2016-06-10 | armv8/ls2080a: configure PMU's PCTBENR to enable WDT | Yunhui Cui |
| 2016-06-10 | sunxi: Move the SPL stack top to 0x1A000 on Allwinner A64/A80 | Siarhei Siamashka |
| 2016-06-10 | sunxi: Downclock AHB1 to 100MHz on Allwinner A64 | Siarhei Siamashka |
| 2016-06-10 | spi: pic32_spi: add SPI master driver for PIC32 SoC. | Purna Chandra Mandal |
| 2016-06-10 | MIPS: Make CONFIG_SYS_DCACHE_LINE_SIZE int, not hex | Paul Burton |
| 2016-06-10 | MIPS: Fix invalidate_dcache_range to operate on L1 Dcache | Paul Burton |
| 2016-06-10 | sunxi: musb: Properly turn of musb controller before booting | Hans de Goede |
| 2016-06-10 | sunxi: Add INITIAL_USB_SCAN_DELAY to Mele_A1000G_quad_defconfig | Hans de Goede |
| 2016-06-10 | sunxi: Enable ALDO3 and ALDO4 in Wobo_i5_defconfig | Hans de Goede |
| 2016-06-09 | siemens,am33x: add draco etamin board | Heiko Schocher |
| 2016-06-09 | dfu, nand, ubi: fix erasing after write finish | Heiko Schocher |
| 2016-06-09 | am335x, dxr2: get ECC sType from I2C eeprom | Heiko Schocher |
| 2016-06-09 | mtd: nand: omap: allow to switch to BCH16 | Heiko Schocher |
| 2016-06-09 | nand: add nand mtd concat support | Heiko Schocher |
| 2016-06-09 | ubi: add new ubi command "ubi detach" | Heiko Schocher |
| 2016-06-09 | siemens,am33x: add ubi fastmap support | Samuel Egli |
| 2016-06-09 | am335x, shc: add support for the am335x based bosch shc board | Heiko Schocher |
| 2016-06-09 | doc, spl, am335x: update am335x-network | Heiko Schocher |
| 2016-06-09 | armv7: omap-common: make SPL board_mmc_init() weak | Heiko Schocher |
| 2016-06-09 | mmc: omap_hsmmc: enable 8bit interface for eMMC for AM33xx | Heiko Schocher |
| 2016-06-09 | mmc: revert mmc: Handle switch error status bit in MMC card status | Heiko Schocher |
| 2016-06-09 | bootstage: call show_boot_progress also in SPL | Heiko Schocher |
| 2016-06-09 | arm, am335x: Enable Spread Spectrum for the MPU | Heiko Schocher |
| 2016-06-09 | am335x: add some missing CM_CLKMODE_DPLL_SSC macros | Heiko Schocher |
| 2016-06-09 | arm, am335x: add some missing GPIO register definitions | Heiko Schocher |
| 2016-06-09 | power, tps65217: add some defines | Heiko Schocher |
| 2016-06-09 | tests: py: disable main_signon check for printenv cmd | Heiko Schocher |
| 2016-06-09 | common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option | Heiko Schocher |
| 2016-06-09 | tiny-printf: Correct the snprintf() implementation | Simon Glass |
| 2016-06-09 | ARM: uniphier: insert dsb barrier to ensure visibility of store | Masahiro Yamada |
| 2016-06-09 | ARM: uniphier: do not erase when updating U-Boot image in eMMC device | Masahiro Yamada |
| 2016-06-09 | ARM: uniphier: do not overwrite fdt_file environment | Masahiro Yamada |
| 2016-06-09 | ARM: uniphier: check return code of setenv() | Masahiro Yamada |
| 2016-06-09 | ARM: uniphier: fix boot mode for PH1-LD11 | Masahiro Yamada |
| 2016-06-09 | ARM: uniphier: support eMMC boot for PH1-LD11 and PH1-LD20 | Masahiro Yamada |
| 2016-06-07 | arm: mxs: Remove misleading comments | Michael Heimpold |
| 2016-06-07 | board: ge: bx50v3: add missing partnum variable | Kimmo Surakka |
| 2016-06-07 | board: ge: bx50v3: disable unused features to improve size and boot speed | Andrew Shadura |
| 2016-06-07 | board: ge: bx50v3: make SATA optional and disabled by default | Andrew Shadura |
| 2016-06-07 | board: ge: bx50v3: make network support optional and disabled by default | Andrew Shadura |
| 2016-06-07 | board: ge: bx50v3: make USB support optional and disabled by default | Andrew Shadura |
