| Age | Commit message (Collapse) | Author |
|---|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
K3 J721E/AM65X:
- UART boot fixes for J721E
- Enabling debug uart for AM65x
DRA7xx/AM57xx:
- Preveinting boot from Invalid boot configuration for AM57xx
Keysonte2:
- Linux Boot fixes for K2 platforms.
AM33/AM43/Davinci:
- Ethernt boot fixes for AM43XX
- USB Host boot fixes for AM43XX
|
|
- Minor Kconfig fixes
- Ensure we use python3 on all CI in all cases.
- Other minor fixes
|
|
Activate early console functionality on AM65x devices to allow for
early diagnostic messages until the main console is ready
to get activated.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The boot parameter table index memory address for J721E was configured
to an incorrect value which prevented the use of this definition to
determine which boot parameter table is active which is needed to be
able to distinguish between primary and backup boot modes. Fix this
issue by updating the value to the correct one also in alignment with
the J721E Technical Reference Manual (TRM).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Keystone2 u-boot loads the initrd image into non-LPAE addressed memory
but linux kernel is running in LPAE. This causes a conflict as kernel
detects that non-memory address is passed and kernel ignores initrd.
There is an existing fixup logic to modify the address in the proper
configuration, but this is disabled at the moment. Enable the fixup
by setting the env variable for this so that initrd can be used
properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
On am571x-idk there can be following configurations based on Jumper J51
and LCD panel detected.
1) J51 removed (6port): 6 port Ethernet. Disable LCD panel.
2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD.
3) J51 placed (LCD) + Panel not detected/not supported.
Configuration 3 is considered invalid as we can't use display nor ICSS1
ethernet ports due to hardware muxing. Alert the user to fix the
configuration and prevent boot.
Alternative was to allow boot and limit to 4 port Ethernet with no display
but this involved introduction of another DTB for the kernel and was
considered not worth the hassle.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Data manual mentions the new silicon revisions as SR instead of PG. Use
the same nomenclature inside U-Boot as well.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add mmc device partition 0 as the seat of the environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable configs to fix USB Host boot mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Early cons will be used in uart boot. Enable the same for j721e_r5
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
mcu uart will be used during uart boot for loading sysfw.itb. Since
sysfw is not yet available during uart load, power-domain cannot be
enabled. We need to rely on ROM for doing that, so disable power-domains
and clocks for mcu uart. Also fix the mcu uart frequency.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable CONFIG_SPL_ETH_SUPPORT to fix ethernet boot support.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add scm_conf syscon node and its parents as well as the ethernet phy
node to u-boot.dtsi. This enables ethernet boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
When running our tests there are some cases where as part of the Python
2.7 to Python 3.6 migration we didn't force Python 3.6 to be used as
everything wasn't yet migrated. Now that everything is, make sure to
tell virtualenv to use python3. In the case of Travis this is best done
by making the tools test happen after the main tests so that it will
already have been run in all cases, TEST_PY_TOOLS is a subset of
TEST_PY_BD.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
clear_bss is already used by 3 arches (x86, arc, xtensa), so make it generic
and provide a weak nop stub for it. This also removes arch-specific ifdef
duplications around clear_bss.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
|
|
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There is no reason to show RAM_ROCKCHIP_DEBUG entry in other .config files
as I see it for Xilinx ZynqMP.
\# CONFIG_U_QE is not set
\# CONFIG_RAM is not set
CONFIG_RAM_ROCKCHIP_DEBUG=y
Add missing dependency on RAM_ROCKCHIP driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Fix a build error
checking consistency...
/doc/board/rockchip/index.rst:
WARNING: document isn't included in any toctree
Fixes: 338b86c9b305 ("doc: boards: Add rockchip documentation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Avoid errors of like
common/console.c: In function ‘console_record_reset’:
common/console.c:615:16: error: passing argument 1 of ‘membuff_purge’
discards ‘volatile’ qualifier from pointer target type
[-Werror=discarded-qualifiers]
615 | membuff_purge(&gd->console_out);
| ^~~~~~~~~~~~~~~~
by casting to non-volatile.
The volatile property stems from declarations like
arch/arm/include/asm/global_data.h:114:
But there is no need to treat gd->console_out and gd->console_in as
volatile in the context of common/console.c.
Fixes: b612312816ff ("console: Add a function to read a line of the output / eof")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In the first version, the result of malloc is checked
with ut_assertnonnull. But on a fail, this macro exit
the function, so previously malloc are not freed.
So to avoid a memleak, we don't use ut_assertnonnull,
but simply check the return of malloc. If one has failed,
we freed all the allocated memory and quit the function.
Reported-by: Coverity (CID: 284403)
Reported-by: Coverity (CID: 284404)
Reported-by: Coverity (CID: 284405)
Reported-by: Coverity (CID: 284406)
Reported-by: Coverity (CID: 284407)
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Currently the size of pci_addr_t and pci_size_t depends on
CONFIG_SYS_PCI_64BIT. For qemu_arm64_defconfig with 4 GiB RAM this leads
to an error
pci_hose_phys_to_bus: invalid physical address
which is due to the truncation of the bus address in _dm_pci_phys_to_bus.
Defining CONFIG_SYS_PCI_64BIT is not a solution as this results in an error
PCI: Failed autoconfig bar 10
So let's use unsigned long for pci_addr_t and pci_size_t if
CONFIG_SYS_PCI_64BIT is not defined.
Considering that 32bit U-Boot is used to launch some 64bit x86 systems we
cannot do without CONFIG_SYS_PCI_64BIT requiring u64 as type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-arc
As usual a bit late a couple of tiny fixes and improvements for ARC.
1. Switch from ARC UART to a convenient DW UART on ARC
simulation platforms. This became avaialble when nSIM got support
of that much more standard UART (starting from nSIM v2019.06).
FWIW also available now in Free nSIM [1].
This among other things allows us finally to use the same one binary
on all our simulators & FPGA-based emulators.
2. Disable networking support on simulated platforms as there's no
network interface in them.
3. Add Virtio net & block devices for the configuration supported
by QEMU so that we may leverage those virtual peripherals and
in fact it's possible to load uImage from TFTP server and bootm it.
4. Minor fixes for HSDK clocks.
5. Rework of how we chose and use compiler options for ARC-based boards.
In real world ARC-based designs are customized more or less but very
rarely match any of our "templates" thus it makes not much sense to
pretend we have some fixed configs, instead we now will fully reply
on a SoC or even board on getting precise set of compiler options
preferably even extracted from real HW via "tcfgen" utility.
6. Well and finally yet another simplification - switch to generic
written in C accessors which are much more universal and just work
for any target supported by the complier as compared to GAS
implementation which is much more target-dependent.
This one was heavily "inspired" by similar implementation for RISCV
and ARM.
[1] https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
|
|
First of all U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not super
fast as we only being executed once. That in return allows us to be more
universal and support wider variety of devices.
And looking forward that will significantly reduce maintenance and simplify
support of newer architectures.
And while at it we add quad-word accessors like readq(), writeq() etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
HDMI PLL has its own xtal with 27 MHz output but we treat it the same
way as other PLLs with 33.33 MHz input.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Pll bypass has priority over enable/disable.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.
Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is not needed now that we have SDL2 in the docker image. It causes
test failures for tests which need video to work.
This reverts commit af800722eb718bec51c5943cfb69231acf15178f.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
- Regulator fix
- Documentation fix
- Correct LOGLEVEL range
|
|
As LOGLEVEL ranges form 0 to 9 set the limit to 10.
Signed-off-by: Marek Bykowski <marek.bykowski@gmail.com>
|
|
The patch fixes some errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
ofdata_to_platdata
The commit e8e9715df2d4 ("regulator: fixed: Modify enable-active-high behavior")
fixed the regulator driver behavior when 'enable-active-high' is defined.
Unfortunately, this patch used dm_regulator_platdata()'s "boot_on" member
to set GPIOD_IS_OUT_ACTIVE flag and enable the regulator.
The issue here is that regulator_common_ofdata_to_platdata() is called
_before_ regulator_pre_probe() function in which the 'regulator-boot-on'
property is asserted.
As a result the GPIOD_IS_OUT_ACTIVE flag is not set and gpio_request_by_name()
called in the former function is not enabling the regulator.
This is problematic for e.g. i.MX ethernet driver, which then tries to
perform initialization without power (and fails).
The solution here is to explicitly enable regulator in regulator_pre_probe()
callback only when 'regulator-boot-on' property is present in device tree.
The GPIOD_IS_OUT_ACTIVE flag is not set at all, but relevant gpio is
requested.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
|
|
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix Coverity CID 280902 issue in vid_console_color()
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Convert to DM:
- bx50v3, mx53ppd, novena, mx6sabresd
- Fixes for Xea Board
- Toradex im8m Verdin
- Cleanup (warp7, mx6sxsabresd)
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/648131788
|
|
- Fix ax25-ae350.rst document.
- Refine RISC-V linker script and start.S.
- Add option to print more information on exception.
|
|
The add instruction on risc-v can have any three sources and targets, so there
is no need for an intermediate mov.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
OpenSBI build steps are marked as normal text in
AX25-AE350 documentation.
Move them into code-block so-that it can show it
as build steps.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Since commit 04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
`make htmldocs` produces a log of warnings like
doc/board/AndesTech/ax25-ae350.rst:373:
WARNING: Block quote ends without a blank line; unexpected unindent.
doc/board/AndesTech/ax25-ae350.rst:0:
WARNING: Undefined substitution referenced: "_ __ ___ _ __ | (___ | |_) |".
Reformat the problematic passages.
Fixes: 04883bf7acca ("doc: update AX25-AE350 RISC-V documentation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When debugging, it can be helpful to see more information about an
unhandled exception. This patch adds an option to view the registers at
the time of the trap, similar to the linux output on a kernel panic.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Due to the two-instruction sequence needed to access arbitrary memory
locations, the RISC-V linker aggressively optimises memory accesses and
jumps at link-time. This is called "linker relaxation," and is discussed
in this SiFive article
<https://www.sifive.com/blog/all-aboard-part-3-linker-relaxation-in-riscv-toolchain>.
One of the optimizations in place is to assume that the __global_pointer
symbol is placed in the gp register. To quote the article:
"...The magic __global_pointer$ symbol is defined to point 0x800 bytes
past the start of the .sdata section. The 0x800 magic number allows
signed 12-bit offsets from __global_pointer$ to address symbols at the
start of the .sdata section. The linker assumes that if this symbol is
defined, then the gp register contains that value, which it can then use
to relax accesses to global symbols within that 12-bit range. The
compiler treats the gp register as a constant so it doesn't need to be
saved or restored, which means it is generally only written by _start,
the ELF entry point."
However, U-Boot instead keeps the global data pointer in gp. This causes
memory accesses and jumps optimized to use the gp pointer to fail. To
fix this problem, we undefine the __global_pointer symbol.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
Configure `CONFIG_SYS_BOOTMAPSZ' per guidance on u-boot@lists.denx.de.
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Use `test' command to test for file existence instead of relying on the
old functionality of the `ext2load' command (which now reports an error
when attempting to load a zero length file).
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy uart pad and iomux code
Enable DM serial and mxc uart
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
